Power Amplifiers
-
Product
Clean Power Source
AC1000A
-
The AC1000 achieves its unique price/performance ratio by actively adjusting the incoming mains waveform to produce a clean output. Other suppliers use convertor techniques to completely recreate the output from scratch. Our solution delivers an output which achieves the required THD with the minimum of hardware and expense. It includes the ability to switch the correction in or out so that the original waveform can be observed and measured if required. Overload and thermal protection systems are built-in and produce an audible warning if activated.
-
Product
C-Band Separate Dispersion Compensation Raman Fiber Amplifier
DRA5228/F
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Raman Fiber Amplifier (RFA) utilizes the optic gain in the Stimulated Raman Scattering (SRS) in the optical fiber and realizes the amplification of the signal optic. FRA, with very low equivalent noise and a wide gain scope, can further widen the gain bandwidth by adopting multi-wavelength optical bump, which represents the development direction of the new optical fiber amplifier.
-
Product
10 MHz to 18 GHz USB Wide Dynamic Range Average & Peak Power Sensor
U2062XA
Power Sensor
The Keysight U2062XA is a fast, accurate and wide dynamic range 10 MHz – 18 GHz USB peak power sensor.
-
-
Product
Powered NIM Crate
NIM 6000 Series
-
The WIENER NIM 6000 series combines the technical advantages of the VME 6000 high efficient , low noise switching power supplies with the high reliability CERN spec. conform WIENER NIM chassis. The modular concept of WIENER NIM 6000 series crates allows fan trays and power supplies to be easily inserted and removed without tools.
-
Product
Low Noise Amplifiers
-
LNA amplifier PE15A1000 is rated at 13 Volts DC maximum and 200 mA. Our low noise radio frequency LNA amp is part of over 40,000 RF, microwave and millimeter wave components available from Pasternack. This coaxial millimeter wave low noise amplifier can ship worldwide the same day of the purchase as with our other available RF parts.
-
Product
SWR / Power Meters
SX40C
-
Frequency range:144 to 470MHz. Power display range:15W 150W. Accuracy at full scale:10%AT.FS. Minimum power at SWR measurement:3W
-
Product
Power Utility Industry
-
Major product types include:*Auxiliary and Tripping Relays*Test Blocks*Arc Flash Protection*Utility Grade Protection and Control Relays*Industrial Controls and Pilot Lamps*On Board Railway Relays, CB’s and Panel Meters
-
Product
Three Phase Power Sources
PS3
-
The PS3 three phase power source was designed to provide a stable alternating current and voltage source for three phase electricity meter test equipment.
-
Product
Operational Amplifiers
Op Amps
-
Operational amplifiers, known also as op amps, play a major role in analog signal conditioning applications. Invented by Karl Dale Swartzel Jr. in 1941, these products are largely used in today’s electronic devices.
-
Product
DC Power Supply
◎PW-4063R
-
*Use Toroidal Transformer. Low EMI & High EMS.*Triple output, 0-32V/0-6A X2 and 5V/3A .Max. 400Watts*Tracking operation. Max. output 64V/6A on tracking series or 32V/12A on tracking parallel.*4 display, Green LED shows Voltage and Red LRD shows Current. Easy to read.*Compact design. G.W. 9Kgs only. Easy to handle.*The resolution of PW-4063R as high as 0.01v and 0.001A.*Provide 4Pcs 10turns micro adjust VR for Voltage and Current adjustment. Easy to operate.*Very low Ripple & Noise, less than 0.4mVrms. Very suit for precise measurement.
-
Product
Power Frequency Transducer
PP1S
-
1. Measuring and conversion IEC 6882. Dielectrical strength IEC 688 4 KVac / 1 min.3. Impulse test ANSI C37.90 / 1989 IEC 255-3 5KV ( 1.2 x 50 us ) 3KA ( 8 x 20 us ) - current coil4. Surge test (ring wave) ANSI C37.90 / 1989 ( 3KV - 0.5us / 100KHz ) IEC 255-3 ( 2.5KV - 0.25ms / 1MHz )5. Adaptability for power system VDE 0110 6. Measuring reliability VDE 3540
-
Product
3-Phase AC Power Source
61700 series
-
The Chroma Programmable AC Power Source model 61700 series delivers pure, 5-wire, 3-phase AC power. Unlike the traditional 3-phase AC power source, it includes low power rating models at very low cost. Users can program voltage and frequency, measure the critical characteristics of the output on its LCD display. It delivers the right solution to simulate all kinds of input condition of UUT to be utilized in R&D and QA. It is also suitable for commercial applications from laboratory testing to mass productions. The 61700 supplies the output voltage from 0 to 300VAC and it can be set individually for each phase. Users also can set the phase angle from 0? to 360?. These kinds of function make the 61700 series can simulate unbalance 3-phase power. Because of the wide output frequency from 15 to 1200Hz, it is suitable for avionics, marine and military application. The AC+DC mode extends the output function to simulate abnormal situation when power line contains DC offset.
-
Product
AC Power Sources
400XAC Series
-
Our 400XAC Series AC Power Sources provides both 1Ø and 3Ø AC or DC power in a single box solution. If you need an AC Power Source with superior application flexibility, look no further than the EEC 400XAC. Ideal for both production and laboratory use, this 3 phase AC Power Source provides a unique feature set at a competitive price point. Our exclusive SmartCONFIG feature allows the 400XAC Series to switch from 1 phase to 3 phase power with the push of a button. This flexibility maximizes your investment while providing you the AC and DC power that your application needs. The 400XAC Series AC Power Source includes the following models: 430XAC and 460XAC.
-
Product
DC Power Supplies
XG 850
-
AMETEK Programmable Power, Inc.
The Sorensen XG Series is an 850 Watt, 1U half-rack DC power supply. The XG Series is the new standard for powerful, programmable DC power systems. Designed for test, production, laboratory, OEM and quality assurance applications, the XG Series provides a wealth of features to ensure accuracy and greater efficiency. It puts clean, reliable power at your disposal and delivers stable, variable output voltage and current for a broad range of development, test and system requirements.
-
Product
IFE Integrated Power
-
EmPower® IFE Integrated Seat Power Systems are based on the advanced technology created for the EmPower® AC In-Seat Power Systems with smaller volume and higher efficiency than can be found in non-integrated systems. The Seat Power Box (SPB) is designed to provide both 110V AC power for passenger PEDs and DC power for the IFE, USB charging ports, and other in-seat equipment. The SPB is capable of operating in several modes including AC/DC, AC only, or DC only, and provides dynamic power allocation between AC and DC outputs.
-
Product
FPD Tester Power Module
67393-120-480
Power Module
The 67393-120-480 FPD Tester Power Module is a new generation of small, stable, high reliability AC to DC power supply. It adopts compact mechanical design and uses Chroma FPD Tester for signal input/output that can provide a total solution for testing the signal, control and power of diversified panels.
-
-
Product
VHF Band 1.0 Watt Amplifier With RF Bypass
-
Teledyne RF & Microwave has developed a 35 to 350 MHz custom amplifier with 1 watt output power. The amplifier has 29 dB gain with 3 dB noise figure. The amplifier assembly has a RF switch so that the RF input can be connected directly to the output bypassing the amplifier. The amplifier goes into the "bypass" state when the DC bias is removed from the switch. This unit is one of a series of amplifiers that covers the 1 MHz to 2100 MHz with similar operation.
-
Product
DC Power Supplies
-
High performance and high reliability, is variable DC regulated power supply used in all fields, from research and development and quality control to manufacturing plants.
-
Product
DC Power Analyser
AESPA01 series
-
Aarohi Embedded Systems Pvt. Ltd
The AESPA01 series is the enhanced version of Aarohi’s 2nd generation of compact power meters. The world’s best-selling power meter is the instrument of choice for a wide range of applications in production testing, quality assurance and Research & Development. Aarohi power meters are easy to use, cost effective and accurate for diverse applications such as the testing of electric devices, the development and evaluation of Pump Industries, Motor Industries, home appliances and induction cookers, battery and AC driven device testing, and conformance tests on uninterruptible power supplies.The exceptional low power performance of the AESPA01 and power consumption software enables users to easily test their instruments to Energy Star.
-
Product
Universal AC-DC Power Supplies
PS-RS35-24-0
-
The PS-RS35-24 is a small, convection cooled 35W power supply for embedded systems. It is a universal design that accepts 88 to 264VAC input and generates up to 1.5A of current at 24 volts. The 24 voltage output can be adjusted with an on board trimpot. The PS-RS35-24 is small, measuring only 99 x 82 x 36mm.
-
Product
Single Channel High Voltage Linear Amplifier
A400
-
The A400 is a general purpose broadband linear amplifier having a fixed amplification of 20 times and capable of bipolar high voltage output of 200. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to 10 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
Product
PON Power Meter
PPM-350D
-
The first PON-awareTM power meter to automatically detect and test next-gen and legacy PON technologies. Compatible with GPON and EPON networks (GPON, EPON, XG-PON, XGS-PON, NG-PON2, 10G-EPON). Supports 10G-capable PON networks. Pass-through mode for ONT/ONU verification. Bluetooth and USB connectivity. Supports legacy & next-gen PON technologies, including NG-PON2. Single-layer PON service activation. Multi-layer PON service activation.
-
Product
Converter Signal Amplifier – 0…10 Vdc – DIN Rail
HD978TR4
-
Configurable signal converter amplifier with 0…10Vdc (10…0Vdc) output. Input range -10 ..+60 mVdc. Standard configuration 0…20 mVdc.
-
Product
DC Power Supply
CX-DC30
-
Shenzhen Chuangxin Instruments Co., Ltd.
DC power supplyThis serial single output switch power supply is a kind of DC regulated power supply with high efficiency and stability.
-
Product
Handheld Optical Power Meter
HOPM-3216
-
Hangzhou Huatai Optic Tech. Co., Ltd.
HOPM-3216 Handheld Optical Power Meter is our newly designed fiber optic tester, it aims at fiber network installation, fiber network engineering acceptance and fiber network maintenance. Combined usage with HOMP3116 handheld optical light source, it offers a quick and accurate testing solution on both SM and MM fibers. Compared with usual power meters, the HOPM-3216 has more great functions/features of automatic wavelength identification and switching and intelligent backlight control. Also the HOPM-3216 features good appearance, good touch feeling and considerate humanity design.
-
Product
Benchtop Amplifiers
-
Benchtop, broadband driver amplifiers are designed and manufactured by utilizing the most advanced PHEMT or MMIC devices, thin film technologies, and an improved DC power supply to deliver a high output power and a superior gain flatness and low noise performance. The standard offering focuses on general purpose applications and covers the frequency range of 1 to 110 GHz. However, custom designs are also offered to meet any user’s specific needs.
-
Product
RF Peak Power Sensors
-
These sensors feature real-time processing and hardware triggering with advanced PC software to capture even the most elusive signals. Measure pulsed, bursted, and modulated signals used in commercial and military radar, electronic warfare (EW), wireless communications (e.g., LTE, LTE-A, and 5G), consumer electronics (WLAN and WiFi 6), as well as education and research applications.
-
Product
DC Power Supply
-
A DC power supply is an instrument that produces a pure, stable DC power supply. There are several important parameters when choosing a DC power supply, including the number of channels, total power, output specifications per channel, resolution, and so on. Each indicator is related to the needs and applications we actually test.
