-
product
12-Ch 10A-250VAC RCV Power Distribution Unit
YAVAR438
- Hardware controlled Enable Input- 12 Power relays up to 10A 250VAC/DC and 300W or 2.700VA switching power- 12 10-mOhm shunt resistors.- 6 Switched 2-Pole sense channels- Single phase isolated or 3-Phases non-isolated switching capabilities, to or from the device under test (power or load)- VPC TriPaddle 96 pins connector.- NI LabView & TestStand driver.- .NET, C/C++, VB driver.- Soft Front panel for direct interface.- CAN Control or Ethernet (with Ethernet to CAN Gateway).- Self-test module available.- Form A
-
-
product
PXI Digital I/O Module With Power Distribution - With DC-DC Converter
40-228-001
The 40-228 provides 32 channels of digital input and 32channels of digital output, together with switched +12V,+5V, +3.3V and -12V supply outputs derived from the PXI backplane. The module is available fitted with a DC-DC converter (40-228-001) which provides an additional -5Vsupply output. Alternatively the module can be supplied with an industry standard footprint for a DC-DC converter(40-228-002) allowing the user to fit one of their own specification if required. The 40-228 includes a breadboard area that allows users to add their own circuitry to the module.
-
product
PXI Digital I/O Module With Power Distribution - Without DC-DC Converter
40-228-002
The 40-228 provides 32 channels of digital input and 32 channels of digital output, together with switched +12V, +5V, +3.3V and -12V supply outputs derived from the PXI backplane. The module is available fitted with a DC-DC converter (40-228-001) which provides an additional -5V supply ouput. Alternatively the module can be supplied with an industry standard footprint for a DC-DC converter (40-228-002) allowing the user to fit one of their own specification if required. The 40-228 includes a breadboard area that allows users to add their own circuitry to the module.
-
product
12-Ch 10A RCV Power Distribution Unit
AR438
AR438 module helps with interconnection, power supply and load switching, monophasic and triphasic, adding the current measurement capability up to 10A.Enable input helps for a safe relay disconnection. It is a quick electrical -hardware- disconnection of the relays and is designed to be an auxiliary safety element, so that loads cannot reach the device under test.
-
product
Power Distribution Unit with Switchable Outputs, Soft Start & Integrated Ethernet Switch
PDU-200
The PDU-200 is a power distribution unit for automatic tests equipment (ATE). Its outputs are software controlled to allow power on sequencing and direct interaction form the test sequence. The integrated 24V power supply provides power for additional equipment like relays and sensors. The PDU-200 is intended to use with an external remote-control panel which provides On & Off buttons as well as an E-Stop and acknowledge button. It’s integrated eight port switch simplifies wiring as no additional components are required.
-
product
Aircraft Power Distribution
CorePower® aircraft power distribution systems from Astronics replace traditional mechanical breaker systems with intelligently controlled solid-state switches to provide next-gen reliability and safety.
-
product
Power Distribution Boards
Power distribution systems can be offered in addition to solutions for power supplies. This includes power distribution boards, which take over the power distribution in your system. When developing the system solution, in addition to the technical requirements such as high energy efficiency, simple further processing is decisive. The competence for high-performance circuit boards, enclosure constructions as well as assembly and system tests, which has been developed over the years, enables us to offer you the best possible power supply and distribution.
-
product
Multi-channel USB and Power Distribution Backplane
USBDR-8
Power worldwide with universal AC adapterDC power from 12V to 50V sourceInstall from 1 up to 8 channels per USBDR-8Daisy chain USBDR-8 to control up to 112 channels using just one USB portUSB 2.0 compatible communication Synchronize all USBPxx-S1 operation in tracking or dynamic control applications Operate on table top, wall mount, rack mount or DIN rail mount Optional DIN rail connection kit for mounting the USBDR-8 to DIN rail available Optional 19" aluminum rack mount plate available
-
product
LED Tester0.3m-2m Integrating Sphere
CX-8000
Shenzhen Chuangxin Instruments Co., Ltd.
Measure Luminous Flux, Luminous efficacy, radiant power, Spectral Power Distribution, Chromaticity Coordinate, Correlated Color Temperature, Peak Wavelength, Dominant Wavelength, Spectral Half Width, Color Rendering Index, Colorimetric Purity, red ratio, Standard deviation of color matching(SDCM), voltage, current, power, power factor, harmonics, and etc. It meets the requirements of CIE standards.
-
product
LED Lighting Test Instrument Integrating Sphere
CX-I.5S
Shenzhen Chuangxin Instruments Co., Ltd.
Measure Luminous Flux, Luminous efficacy, radiant power, Spectral Power Distribution, Chromaticity Coordinate, Correlated Color Temperature, Peak Wavelength, Dominant Wavelength, Spectral Half Width, Color Rendering Index, Colorimetric Purity, red ratio, Standard deviation of color matching(SDCM), voltage, current, power, power factor, harmonics, and etc. It meets the requirements of CIE standards.
-
product
1U 2 Slot VME64 Mini Crate
VME8001
The Model VME8001 is a 2 slot VME crate, suitable for 6U x 160mm boards, with VME64 compliant backplane. The Unit is powered by 110 ÷240 Vac, 50 ÷ 60 Hz,. The power distribution is 16A@+5V, 7A@+12V, 0.7A@-12V.
-
product
2U 4 Slot VME64 Mini Crate
VME8004B
The Model VME8004B is a 4 slot VME crate, suitable for 6U x 160mm boards, with VME64 compliant backplane. The Unit is powered by 100 – 240 Vac (50 – 60 Hz). The power distribution is 25A@+5V, 10A@+12V, 10A@-12V. The VME8004B provides automatic daisy chain and supports CBLT data cycles.
-
product
Cable Test And Fault Location Systems
Power outages can cause serious financial and social damage, as they disrupt the normal operation of security and life support systems, destabilise the operation of industrial facilities, transport network, and utilities. Reliable power distribution is ensured by an effective prevention and prompt elimination of cable faults and electrical equipment failures. KharkovEnergoPribor Ltd. offers a range of integrated solutions designed for testing power cables and electrical substation equipment, as well as locating various types of faults in underground utilities.
-
product
Ethernet-based Distributed Systems
DMC-3425
The DMC-3425 is the first product in Galil's new E-Series line designed specifically for Ethernet-based distributed systems. The DMC-3425 provides a highly versatile and powerful form of distributed control where multiple DMC-3425 controllers are linked together. When linked, one DMC-3425 is designated as the master over the other DMC-3425 controllers in the distributed system.
-
product
Surge Power (Joule Rating 342) (10) 5-20R 0U V/H
EPSS-1020-HV
EPSU Power (Basic / Surge / Metered / Value) – rack mountable power distribution, 120V, optional surge suppression, and amp meter
-
product
Emergency Power Supply Units (EPSU) (14) 5-15R 1U/0U V/H
EPS-1415-HV
EPSU Power (Basic / Surge / Metered / Value) – rack mountable power distribution, 120V, optional surge suppression, and amp meter
-
product
Electrosurgery Analyzers
Electrosurgery Analyzer is the ESU tester you can depend on for complete preventive maintenance and electrosurgical device safety to completely test these critical functions:* Measures current, voltage and power output.* Tests RF leakage from output to ensure no hazardous currents are present.* Performs Return Electrode Monitoring (REM) tests.* Measures crest factor.* Performs automatic power distribution curve at a wide range of test loads.
-
product
UNI-T Series
Weshine Electric Manufacturing Co., Ltd
mainly used to measure the wire resistance of cables, the contact resistance ofswitches, connectors, relays, the resistance of coils, motors, transformer windings, and equipment enclosures, lightning protection belts, ground beams, structures, cabinets, steel bars, Test the connection resistance between metal components of water pipes, windows, guardrails, radiators, assembly lines, etc. It is widely used in telecommunications, electric power, meteorology, computer rooms, oil fields, power distribution lines, tower transmission lines, gas stations, factory grounding grids, lightning rods, etc.
-
product
Automatic Power Control system
The Automatic Power Control system cuts the incoming power supply to a traction unit for short periods. This is required where power supplied from one part of a power distribution system in separated from another by a neutral section. Its fitment prevents damage to the power distribution system or the vehicle.
-
product
SPSR-2030 (200-3000nm) Super Pure Spectral Radiation Scanning Analyzer
SPSR-2030
Hangzhou Everfine Photo-E-Info Co., LTD
SPSR-2030 adopts double-monochromator design, which can realize super-pure&fine full-spectrum scanning ( 200-3000nm), the test parameters including but not limited to spectral power distribution, peak wavelength, dominant wavelength, CCT (correlated colour temperature), CRI (color rendering index), SDCM (standard deviation of color matching), color purity, and etc.
-
product
Tap Changer Analyzers & Winding Ohmmeters
Winding resistance test of inductive test objects, such as power transformers, is one of the most effective non-intrusive ways of checking its condition. Due to their advanced design, DV Power winding resistance meters provide high test currents (up to 100 A DC) and high accuracy (up to 0.1%) within light and portable test instruments. In addition to winding resistance measurement, it is also possible to perform simple, quick and reliable transformer on-load tap changer condition assessment by recording the test current during tap changer operation, also known as DVtest. Because of that, problems with a tap changer connection, contacts, and switching procedure can be detected.DV Power winding ohmmeters consist of single-phase RMO-T and three-phase TWA series. Models from the TWA series are designed for six-winding resistance measurement of power and distribution transformers, with only one single-step cable setup. As a result of reducing the total test time, it enables significant saving of time and money.Typical application areas of these instruments are high-voltage substations and industrial environments. They are intended to measure the resistance of:Transformer windingsOn-load tap changersGeneratorsElectrical motorsHigh-current bus bar jointsCable splicesWelding joints
-
product
*Beam Profiling For 266nm To 3000µm
Unlike a power meter that measures average or instantaneous Watts or Joules of the overall laser beam, knowing how the power is distributed within the beam is equally as important. As an example, if you want to cut something the power should generally be focused in the center of the beam to concentrate the power density in a very small area but if you were trying to weld something with all the power in the center you would poke a hole in the weld; requiring the power to be equally distributed as in a top hat profile.
-
product
Metered Power with Audible Alarm (14) 5-15R 1U/0U V/H
EPS-1415-HVA
EPSU Power (Basic / Surge / Metered / Value) – rack mountable power distribution, 120V, optional surge suppression, and amp meter
-
product
Focal Spot Analyzer
Measure your laser beam power distribution and focal spot size of wavelengths from 300 – 1100nm. The average power can be from <1 to 400 Watts and up to 5 kW for FSA-HP, the focal spot can be as small as 34.5μm. The FSA can also be used to measure how the focal spot shifts with power during its critical start-up phase.
-
product
Metered Power with Audible Alarm (14) 5-20R 0U V
EPS-2420-VA60
EPSU Power (Basic / Surge / Metered / Value) – rack mountable power distribution, 120V, optional surge suppression, and amp meter
-
product
7U 21 Slot VME64 Low Cost Crate
VME8011
The Model VME8011 is a 21 slot VME crate, suitable for 6U x160mm boards, with VME64 compliant backplane. A 1U space is reserved for Fan Unit.The Unit is powered by 100÷230 VAC, 50 ÷ 60 Hz. The Mod. VME8011 has a pluggable Power Supply. The power distribution is +5V@60A, -12V@6 A, +12V@8.9A.
-
product
Single-Phase Transformer Winding Resistance Meters
RMO-TT Series
RMO-TT series is perfect for measuring winding resistance of inductive objects such as power and distribution transformers or autotransformers. Additionally, every transformer resistance meter from RMO-TT series can analyze:tap changers,generators,electrical motors,high-current busbar joints,cable splices,and welding joints.Transformer demagnetization can also be performed with all RMO-TT instruments.The series is consisted of 3 models, with maximal test current from 40 A (RMO40TT) to 100 A (RMO100TT). RMO100TT is the only portable transformer resistance meter in the market with 100 A DC output current.The three independent channels enable testing of three windings in series. Consequently, a user can measure winding resistance in every tap position of an on-load tap changer without discharging between the tests.In addition to winding resistance measurement, a user can perform a detailed on-load tap changer analysis by analyzing recorded graphs (10 kHz sampling rate) and by measuring vibrations on an external tap changer tank.All RMO-TT instruments have a built-in tap changer control unit. Because of this, it is possible to remotely control on-load tap changer (OLTC) directly from the device. Also, a user can program DV-Win software to do everything automatically – running winding resistance tests and changing OLTC tap positions.The DV-Win software also enables control and observation of the test process, as well as saving and analyzing the results on a PC. It provides a test report, arranged in a selectable form as an Excel spreadsheet, PDF, Word, or ASCII format. Additionally, DV-Win measures and calculates the OLTC transition time, the ripple and the winding resistance for each tap changing operation. The software can also perform the calculations necessary for the “Heat Run” test.All results can be exported in the report format.
-
product
4U 8 Slot VME64 Mini Crate
VME8008B
The Model VME8008B is a 8 slot VME crate, suitable for 6U x 160mm boards, with VME64 compliant backplane. The Unit is powered by 100 – 240 Vac (50 – 60 Hz). The power distribution is 50A@+5V, 10A@+12V, 10A@-12V. The VME8008 provides Automatic daisy chain and supports Chained Block Transfer (CBLT).
-
product
Off-Line Base Test Platforms
To configure your Base Test Platform, the following parts can be added to the 6TL-19 bare half-rack:– Test Rack Manager, to control the test station.– Power Distribution Unit.– Uninterruptible Power Supply– Industrial PC or NI PXI to control the platform– 19’’ Monitor and keyboard with trackball– VPC Mass Interconnect Receiver (6 or 12 slots)– YAV Modules– Accessories: Beacon, Air inlet Pneumatic kit…– Any 19’ Instrument
