Elemental
of the periodic table.
-
product
Digital Liquid Mass Flow Meters / Controllers
LF-F/LV-F Series
The LF-F and LV-F Series are digital liquid mass flow controllers using a Peltier element which cools the liquid rather than using the more common method of thermal heating. This technique removes the risk of boiling chemicals with a low boiling point, thus allowing for greater chemical control.
-
product
Very Compact Low-Frequency Control Element
750-LFC
The 750-LFC low-frequency-control element’s impressive power-to-size-ratio and versatile features make it the right choice for any application demanding superior low-frequency performance in low-profile systems. It pairs perfectly with ULTRA‑X40 and LINA systems, extending response down to 36 Hz for deeper, richer bass with total control.
-
product
elemental analyzer
SPECTRO XEPOS
SPECTRO Analytical Instruments GmbH
An elemental analyzer designed for demanding applications – the SPECTRO XEPOS energy dispersive X-ray fluorescence (ED-XRF) spectrometer redefines XRF analysis with exceptional new levels of performance
-
product
Class A Ovens
Gruenberg ovens can be designed as Class A ovens to conform to OSHA, NFPA 86A, Factory Mutual (FM) and Factory Insurance Association (FIA) requirements. Class A ovens are equipped with a high exhaust rate: because the heating elements are an ignition source so a high exhaust rate is needed to dilute the volatile vapors below the “lower explosive limits.” As a result, the heating elements’ kW must be sufficiently increased to compensate for the heat loss caused by the above-normal exhaust rate. In addition, for a Class A oven to be energy efficient, the additional kW required must be carefully calculated according to solvent load and operating temperature requirements.
-
product
EtherCAT Slave System
EPS Series
The ADLINK complete EtherCAT solution, from hardware to middleware to software, with every element tailored for dedicated EtherCAT functionality, includes PCIe-833X Series master controllers, EPS slave systems, and remote monitoring and control providers. As well, ADLINK’s Softmotion one-stop control kernel delivers flexible and easy-to-use intelligent platforms for driving next-generation modern Smart Factories. ADLINK's EPS slave system brings the power the flexibility to EtherCAT environments. State-of-the-art modular construction allows the EtherCAT slave to be configured to fulfill the needs of both small local applications and expansive distributed platforms. The EPS system with comprehensive and high-density I/O modules that include DI/O, pulse-chain motion modules. Leveraging ARM and FPGA technologies, the EPS slave is able to monitor and report system integrity via EtherCAT communication, while relay module lifecycle and signal integrity of analog output are monitored cyclically, and hot swappability reduces downtime significantly. Uniquely designed for full operability in conditions from -20°C to 60°C,the EPS slave system is also fully compliant with the EN 60068-2 standard for shock and vibration and EN 61000-6 for heavy industrial EMC protection, as well as emission certification. Corresponding ESI files for each EPS system can be generated thru ADLINK's Windows-based EtherCAT slave utility, LinkMasterPro™.
-
product
Tubular Infrared Carbon and sulfur Analyzer
8510-CS
Wuxi Jinyibo Instrument Technology Co., Ltd.
Determination of elements: carbon and sulfur combined measurementAnalytical principle: tube furnace combustion infrared absorption method detectionAnalysis range: carbon: 0.0010%-10.000% ( expandable to 99.9999%) Carbon: 0.0005%-0.500% ( expandable to 99.9999%)Analysis error: carbon: in line with GB/T223.69-1997 standard sulfur: in line with GB/T223.68-1997 standardAnalysis time: 20-100 seconds adjustableElectronic balance: not quantitatively weighed, weighing range: 210g/0.001g
-
product
HDD-related Products
These products support the elements that read and write information on magnetic disks.
-
product
Laser Power and Targeting
3M
A thin film-based single element thermopile. The highest output detector in our line-up.
-
product
IEC60068-2-75 Ik08 Spring Impact Hammer
CX-IK08
Shenzhen Chuangxin Instruments Co., Ltd.
The spring Hammer consists of three principal parts: the body, the striking element and the release system. It's used to test the mechanical integrity of product enclosures. After applying the impact with the hammer, the product is examined with accessibility probes to determine access to shock, energy, and injury hazards. Built in exact accordance with IEC/EN, UL/CSA and other international standards.
-
product
Web Application Testing Tool
Sahi
Cross browser and Automated Regression Testing Tool: Record and playback any web application on any browser, any operating system. Recording saves time and helps non-technical users contribute to automation. The Sahi Controller helps easily identify and experiment with elements on any browser. The same script works on all browsers.
-
product
Ultrasonic Thickness Gauge
MMX-6
The MMX-6 is a simple to use hand-held Ultrasonic Thickness Gauge with the ability to measure through paint and coatings and eliminate the thickness of the paint or coating. The MMX-6 uses a dual element style transducer. With the single press of a button, the MMX-6 can be switched between pit or flaw mode ( pulse-echo), and through paint/coatings mode (echo-echo) for maximum inspection efficiency. The MMX-6 is equipped with a bundle of features to make your job easier: Alarm mode, high speed scanning, and data send are the main features of the MMX-6. The MMX-6 comes as a complete kit, ready to use, and is backed by Dakota Ultrasonics 5 year limited warranty.
-
product
Virtual Access Router
Access router is a sort of shorthand term for an Internet access router or wide area network (WAN) access router. When deployed by an organization this network element is often called an enterprise router, and is traditionally implemented as a dedicated hardware appliance on the subscriber premise. However, the access router functionality may be virtualized. Virtualization means the software is separated or de-coupled, from the customer premise equipment (CPE) hardware. Such virtualization results in a virtualized network function (VNF), which may also be called a software access router or virtual access router.
-
product
Ka-Band Silicon 5G Quad Core IC
AWMF-0108
The AWMF-0108 is a highly integrated silicon quad core IC intended for 5G phased array applications. The device supports four Tx/Rx radiating elements, includes 5 bit phase and 5 bit gain control for analog RF beam steering, and operates in half duplex fashion to enable a single antenna to support both Tx and Rx operation. The device provides 26 dB gain and +9 dBm output power during transmit mode and 28 dB coherent gain, 5.0 dB NF, and -28 dBm IIP3 during receive mode. Additional features include gain compensation over temperature, temperature reporting, Tx power telemetry, and fast beam switching using eight on-chip beam weight storage registers. The device features ESD protection on all pins, operates from a +1.8 V supply, and is packaged in a 48 lead 6x6 mm QFN for easy installation in planar phased array antennas.
-
product
Salt Spray Chambers
Dongguan Amade Instruments Technology Co., Ltd
Salt spray chamber is intended to use method of salt-spray corrosion to evaluate the performance of corrosion resistance of specimens to salt fog under the specified conditions. It is capable of simulating a locally salt mist environment in which the test piece is placed. There are different types of salt fog chambers including microprocessor digital version, touch-screen control version and compound version featuring temperature&humidity control and adjustment. widely applied to components and parts, electronics elements, metal materials etc.
-
product
Hall Motor Tester
Shanghai Aoboor Electric Co., Ltd.
Applicable to no-load test and any DC motor with internal hall elements.
-
product
HIGH VOLTAGE SCR CONTROLLED POWER SUPPLY
xPS Series
High Voltage SCR Controlled Power Supply, P/N 18278PS Power Rating: 350 KW. Input: 480 VAC, 3 PH, 60 Hz Output: 0 to 5000 VDC, 70 Amps max Ripple: 2 % approximately at maximum rated voltage Configuration: 12 pulse externally SCR controlled rectifier system Protection Devices: Input contactors Overload relay shutoff Input surge suppressor Thermal switches Output current limiting resistor (made with 5 Ohm Kanthal heating element) Emergency power shutoff Cooling: Each 6 pulse rectifier assembly is cooled by three 10” fans Interface: 4/20 ma converter interface for output voltage and output current to SCR controller. Enclosure: The overall dimension of the unit is (78”H x 38”W x 53”D). It is comprised of two separate enclosures each with dimensions of (78” H x 38” W x 26” D) which are integrated together to form a single enclosure. Each half enclosure has one 6 pulse transformer and one 6 pulse high voltage rectifier. Weight: Approx. 5000 lbs. SCR Controller: The 12 pulse SCR controller is supplied by the customer. We were responsible for the 12 pulses Transformer and 12 pulses Rectifier section. Portability: Unit can be lifted up with a fork lift. It can also be moved around with a 5000 lb pallet jack. Transformer: Two 200 KVA transformers are used to step 480 VAC to 3750 VAC each in a 12 pulse configuration Rectifiers: Two 6 pulse rectifier assemblies capable for 5000 VDC and 60 Amps output were used. The high voltage rectifier assemblies are isolated and protected in a fiberglass plenum within the enclosure. Blocking Diode: Each diode of the 6 pulse rectifier consists of 10 diodes in series to offer a blocking voltage of 12000 V (PIV)
-
product
Multi-angle Polarized Light Scattering Measurements
LISST-VSF
In-situ measurements of P 11, P12 and P22 elements of scattering Mueller matrix, (P11 is VSF) from 15-150º.VSF (P11) only at small angles, 0.05 to 10º in 32 logarithmic steps in angles.Only two detectors employed with absolute radiant sensitivity (A/W) calibration.Beam attenuation measured with optics similar to our LISST-100X.Roving Eyeball™ optics permit 1-degree resolution in angles between 15 -150º.Sampling rate at 3 seconds per measurement set (involves 3 turns of Roving Eyeball with unpolarized, vertical, and horizontal polarized laser).Daylight rejection by laser modulation.Dynamic range in VSF measurements extended via laser power modulation.Data from small and large angles in a single data stream, including depth and temperature.
-
product
Imaging X-Ray Photoelectron Spectrometer
AXIS Supra+
X-ray photoelectron spectroscopy (XPS) is unique in providing quantitative elemental and chemical state information from the uppermost 10 nm of a materials surface. The AXIS Supra+ (also known as Kratos Ultra 2+ in Japan) is a market leading X-ray photoelectron spectrometer combining state-of-the-art spectroscopic and imaging capabilities with the highest level of automation currently available. Unrivalled large area spectroscopic performance allows photoelectron spectra to be acquired from all types of materials including metals, semi-conductors and insulators. Fast, high spatial resolution XPS imaging reveals the lateral distribution of surface chemistry and aids further characterisation with selected small area analysis.
-
product
Inductive Sensors
In general, inductive proximity switches consist of four basic elements: a coil, an oscillator, a threshold switch and an output stage with short-circuit protection.The oscillator generates a high frequency, electromagnetic alternating field which is emitted from the active face of the coil.Eddy currents are induced in a metal object that enters this field. These eddy currents draw energy from both the electromagnetic field and from the oscillator which is consequently attenuated.The more energy taken the closer the metal object moves towards the active face. The threshold switch switches on the output stage at a defined attenuation value.In proximity switches with a DC voltage supply, this switch is designed as an NPN transistor which switches the connected load to the negative pole or as a PNP transistor which switches the load to the positive pole. The output stage is a thyristor or a triac in AC voltage switches.
-
product
X-Band Silicon Radar Quad Core IC
AWS-0103
The AWS-0103 is a highly integrated silicon quad core IC intended for radar and 5G phased array applications. The device supports four radiating elements, single beam transmit, and dual beam receive and includes all requisite beam steering controls for 6 bit phase and gain control. The device provides 21 dB gain and +15 dBm output power during transmit mode and 7 dB gain and +7 dBm IIP3 during receive mode. Additional features include gain compensation over temperature, temperature reporting, and fast beam switching using eight on-chip beam weight storage registers. The device features ESD protection on all pins, operates from a +1.8V supply, and is packaged in a 56 lead 7x7 mm QFN for easy installation in planar phased array antennas.
-
-
product
Hydrophone
RESON TC 4032
The TC4032 general purpose hydrophone offers a high sensitivity, low noise and a flat frequency response over a wide frequency range. The high sensitivity and acoustic characteristics makes TC4032 capable of producing absolute sound measurements and detecting even very weak signals at levels below “Sea State 0”. The TC4032 incorporates an electrostatically shielded highly sensitive piezoelectric element connected to an integral low-noise 10dB preamplifier. The TC4032 preamplifier is capable of driving long cables of more than 1.000 meters, and the preamplifier features an insert calibration facility.
-
product
Magnetostrictive Sensors
Linear position sensors with a profile design are contact-free and absolute measurement systems for the precise detection of one or more positions. They deliver convincing performance in harsh environments, for example in presses, injection molding machines or gantry robots, because they are made of an hermetically sealed IP67 aluminum housing. The magnets of the position encoder act on the measurement element through the wall of the profile.
-
product
FlexVPX Backplane
FlexVPX provides system designers with the flexibility and performance required for the most demanding applications. The ability to interconnect 2 and 3-slot 3U VPX compliant backplanes allows for custom system configurations using COTS hardware. Backplanes are equipped with PCI Express bridges that ensure fast and high-throughput for point-to-point communication between different elements in the system.
-
product
2-MGEM Optical Anisotropy Factor Measurement System
The 2-MGEM Optical Anisotropy Factor Measurement System is a normal-incidence polarization reflection microscope designed to measure the sample Mueller matrix and is a 2008 R&D 100 Award Winner. This system is designed specifically to evaluate the Optical Anisotropy Factor (OPTAF) of cross sections of TRISO nuclear fuel pyrocarbon layers. Other possible material characterizations include measuring Mueller matrix elements of other crystals, carbon compounds, and thin film coatings (e.g. surfacedeposition films) at normal incidence. The 2-MGEM can also measure retardation (d), circular diattenuation (CD) and the polarization factor (ß). These parameters are not measurable using older techniques, since those techniques do not incorporate a compensating optical element.
-
product
Analytical Reference Materials & Standards
Agilent, now with former Ultra Scientific, offers a comprehensive portfolio of analytical standards, reference materials and certified reference materials for environmental, food safety, elemental analysis, instrument calibration, tuning mixes, and more.Reference materials and certified reference materials are substances that are tested to be homogenous and have fixed values of its concentrations. These standards are a critical component of your application workflow - from sample prep, instruments, columns, supplies, and services. The success of your analysis depends upon the quality of your reference material. All Agilent standard reference materials have been manufactured to the highest quality in an ISO 9001, ISO 17025 and 17034 accredited facilities to ensure the accuracy of your analyses.If you need a custom reference material, partner with us to design and develop a custom standard to your specifications.
-
product
On-line Crossbelt Analyzers
CNA Range
CNA online elemental analyzers are available in three models:*CNA³: This cross belt analyzer is designed for minerals applications that feature wide conveyor belts with deep loads and large material size. It is an open analyzer that is installed below the belt with both the neutron source and the detectors below. *CNA Pentos Cement: This cross belt analyzer is used primarily in cement and related industries. It is a closed analyzer that encircles the conveyor belt with the neutron source below the belt.*CNA Nickel: This cross belt analyzer offers real-time quality control for the nickel ore mining industry.
-
product
Carbon / Sulfur Analyzer
ELEMENTRAC CHS‑r
The ELEMENTRAC CHS-r elemental analyzer determines the elements carbon, sulfur and hydrogen by combustion of the sample in an oxygen stream and subsequent measurement of the combustion gases CO2, SO2 and H2O in selective infrared measuring cells. A high sample weight of up to 500 mg ensures excellent reproducibility of the measurement results, even for heterogeneous samples.
-
product
Test Slave For The LIN Bus With Various I/Os
PLIN slave
The PLIN slave is an evaluation board with an interface for a LIN 2.0 bus. The device also offers comprehensive I/O functionality, which is accessible via operating and display elements.
-
product
Primary Test Equipment
LET-1000-RD
It allows to perform with sufficient power, all the primary current injections to test the proper function and wiring of all the elements that compose the protection and measuring section in a substation.The regulation system is based on a continuously variable autotransformer (Variac) that supplies to a power transformer that delivers the high current outputs and isolate the main supply from the load. A built-in ammeter and a timer gives the information about the current value and the operation time of the relay or breaker under test.
