Strain Gages
measure of displaced surface elements.
See Also: Strain Gauges, Strain Gage Amplifiers, Strain Gage Signal Conditioners, Strain
-
Product
Through Hole/ Donut Load Cell (3.00 O.D.) Compression Only
THD SERIES
-
Our THD Series through hole donut load cells offer an outside diameter of 3.00 inches and up to nine different through hole diameter options per capacity range. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial Environments.
-
Product
Force Load Cells
-
TE Connectivity (TE) offers load cell assemblies for test and measurement applications that require high performance or unique packaging. Our broad range of packaged load cells feature foil strain gages enabling OEM's to measure force with low cost and high reliability. The gages produce a high level of output signal for a low operating stain using inorganic materials to offer long term stability. Load cells are gaged in a variety of materials from high strength stainless steel to special alloys.
-
Product
PTI/PMAC/USB Sensor System Examples
-
*System for any strain gage based sensor*Compatible with every sensor is this catalog*Process monitoring*Process control*Portable datalogging*Portable, compact, and lightweight
-
Product
NI-9236, 10 kS/s/channel, 350 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module
785996-01
Strain/Bridge Input Module
10 kS/s/channel, 350 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module - The NI‑9236 measures dynamic strain on all channels simultaneously, allowing for synchronized, high-speed measurements. This capability is important for applications, such as impact tests, that require comparison across many channels at a particular instant in time. The NI‑9236 includes built-in voltage excitation for quarter-bridge sensors. It also has 60 VDC isolation and 1,000 V rms transient isolation, providing high‑common‑mode noise rejection and increased safety.
-
Product
Socket Wrench Torque Sensor Rotating Type
RSS SERIES
-
Our RSS Series rotating socket wrench torque sensors are available in ranges from 10 ft-lbs. through 250 ft-lbs. and provide accurate measurements of bolt or nut wrenching torques. These sensors are bi-directional so both tightening and break-away torques can be measured. Unlimited rotation of the ball bearing supported sensor shaft allows monitoring of the total fastening cycle. The sensing element incorporates bonded foil strain gages of the highest quality, along with coined silver slip rings and two silver graphite brushes per ring for data transmission.
-
Product
Mini Load Column Load Cell Compression Only with Mounting
MLC SERIES
-
The MLC Series is our miniature high capacity compression only load cell/force sensor, featuring low profile compact size for a wide range of portable and dedicated applications up to 30,000 lb The load diameter is slightly convex for accurate load distribution. Low deflection through design results in ultra fast frequency response. The MLCs are designed to be mounted in a shallow machined flat pocket or smooth flat surface, either free or fastened via a bottom 6-32 tapped hole. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial Environments.
-
Product
Strain sensors
SG-01
-
The Strain Gage SG-01 is the fibre optic equivalent of an electrical strain gage. The Strain Gage SG-01 can be mounted directly on the surface of a structure by means of an adhesive. In this way, the fibre sensor makes direct contact with the surface and therefore measures directly the strain at the surface.
-
Product
DMS Transmitter
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Transmitter for load cells and the evaluation of strain gages in 6 mm housing with calibrated range selection.Detection signals from sensors for physical variables such as displacement, angle, pressure or force. Functional safety up to SIL 2, SIL 3 redundant to parameterization via interface or intuitively, directly on the device. Universal use with 24 V DC or AC power supply.
-
Product
High Temperature Diametral Extensometers (1000 C)
Model 3580
-
Jinan Testing Equipment IE Corporation
This model is for diametral strain measurement with furnace and induction heating systems. Quartz rods and water-cooling allow the unit to be used for high temperature testing of metals, ceramics and composites. With induction heating, this model often can be used without water-cooling. When used in furnaces, the extensometer is often mounted directly to the furnace side cut-out. Optional load frame mounting brackets are available for supporting the extensometer in cases where furnace mounting is not possible. These optional mounts are used with induction heating or furnace systems. The Model 3580 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
Data Acquisition Conditioner
D4
-
The Model D4 Data Acquisition Conditioner is a portable, USB-powered precision instrument for use with resistive strain gages and strain gage-based transducers.
-
Product
Full Bridge Thin Beam Force Sensors
TBS SERIES
-
The TBS Series thin beam force sensors many different parameters found in medical instrumentation, home appliances, process control, robotics, and automotive are exceptionally suited for small load measurements. They are designed to measure and many other high volume applications. A specially developed integrated strain gage includes all balancing, compensating and conductive elements and is laminated to the beam to provide excellent stability and reliability.
-
Product
Fracture Mechanics Clip-On Gages
Model 3541
-
Jinan Testing Equipment IE Corporation
The Model 3541 is designed for determination of fracture mechanics parameters such as JIC, KIC, R-curve, fatigue crack growth rate (da/dN), and testing to standards such as E1820, E399, E647, etc. These COD gages conform to the requirements of E1820 (the replacement for E813 and E1737) for JIC and R-curve determination. Special configurations are available to meet the requirements of ASTM E399 for fracture toughness (please consult the factory for these configurations). In addition, the modified groove design complies with E1820 tests where greater stability and accuracy results from the sharper groove root. Clip-on gages are used for a variety of fracture mechanics tests, including compact tension, arc shaped, disk shaped, bend specimens or other specimen geometries in compliance with ASTM and other standards organization’s test methods. Clip-on gages can be used directly on test specimens where the knife edges are integral with the test specimen or, alternately, with optional bolt-on knife edges mounted on the test specimen.The Model 3541 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
Sensor Placement & FEA Analysis
GageMap - GM
-
APEX Turbine Testing Technologies
Apply strain gages and accelerometers to your finite elementmodel independent of the mesh anywhere you want, or letGagemap do it for you.
-
Product
Rosette Strain Gauges
-
Rosette Strain Gages have three measuring grids arranged at an angle of 0°/45°/90° or 0°/60°/120°
-
Product
High Temperature Furnace COD Gages (1200 C or 1600 C)
Model 3548COD
-
Jinan Testing Equipment IE Corporation
These COD gages mount on a water-cooled bracket, which is mounted on the furnace side cut-out or with optional load frame support brackets. The standard temperature version (to 1200℃) is supplied with high purity alumina rods. The high temperature option is furnished with alpha grade silicon carbide rods. Rods are made to order to the length required for your furnace. Mounting brackets may be integrated with the furnace cut-out. Epsilon can also provide optional load frame mounting brackets to fit your test frame. Contact edges on the test sample should be somewhat rounded (not sharp knife edges) for best performance with this model. The Model 3548COD extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
Torque Transducers
-
The technology behind our torque sensors are strain gages. These gages are arranged into a Wheatstone Bridge circuit, which converts the physical, mechanical force into an electrical signal that can be filtered, displayed, and recorded for further processing. This very accurate radiometric electrical signal is proportional to the applied mechanical force.
-
Product
Through Hole/ Donut Load Cell Compression Only
THA SERIES
-
Our THA Series through hole donut load cells offer an outside diameter of 1.00 inches and up to two different through hole diameter options per capacity range. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
Product
NI-9236, 10 kS/s/channel, 350 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module
779994-02
Strain/Bridge Input Module
10 kS/s/channel, 350 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module - The NI‑9236 measures dynamic strain on all channels simultaneously, allowing for synchronized, high-speed measurements. This capability is important for applications, such as impact tests, that require comparison across many channels at a particular instant in time. The NI‑9236 includes built-in voltage excitation for quarter-bridge sensors. It also has 60 VDC isolation and 1,000 V rms transient isolation, providing high‑common‑mode noise rejection and increased safety.
-
Product
Prop Shaft Torque Measurement Systems
-
Advanced Telemetrics International
ATi Telemetry Systems are typically used to transmit data from rotating shafts or machinery to a stationary receiver. The Miniature Strain Gage Transmitter can be attached to strain gages adhered to your shaft in order to transmit shaft torque and thrust while the system is running.
-
Product
Mini Load Cells
-
Interface Mini™ load cells are designed for light touch, light weight, and compact applications. Our miniature load cells provide exceedingly accurate measurements similar to our LowProfile load cells that have our proprietary strain gages. All our miniature beam load cells, load buttons, load washers, rod end load cells, S-type load cells, and platform scale load cells can all be ordered in range of different sizes. Capacities are available as low as 0.11 lbf (0.5 N) and as high as 1,124K lbf (5,000kN). A variety of our miniature load cells are designed for off-the-shelf and OEM applications. Our engineers can also work with you to design custom load cells to fit your exact specifications and requirements.
-
Product
Miniature Axial Extensometers
Model 3442
-
Jinan Testing Equipment IE Corporation
Weighing as little as 8 grams, these miniature extensometers are designed to have very low operating force with minimal specimen influence. All use an improved version of Epsilon’s dual flexure design which makes them very rugged for their size. With a module height of 15.2 mm (0.6 inches), they will fit in the limited space between grips that is typical with small test samples. Gauge lengths can be as short as 3 mm or as long as 50 mm. A newly designed gage setting pin and assembly allows the gauge length to be set accurately and repeatably to ASTM and ISO requirements for all gauge lengths. Reengineered quick attach wire forms provide simple and secure specimen attachment. Wire forms for round and flat specimens are included, as well as flat, 3-point, and vee knife edges. The wire forms may be removed to enable mounting using elastic bands or springs. A tethering attachment point provides fall protection and enables counterbalancing of the extensometer’s weight when testing delicate specimens.Model 3442 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller and Epsilon will equip the extensometer with a compatible connector wired to plug directly into the controller. For systems lacking the required electronics, Epsilon can provide a variety of solutions for signal conditioning and connection to data acquisition systems, chart recorders, or other equipment.
-
Product
T-Rosette Strain Gauges
-
Tee Rosette Strain Gages are for measuring orthogonal strains when the principle directions of stress are known. All patterns have two grids oriented at 0° and 90° angles.
-
Product
Rugged, Long Gauge Length Extensometers
Model 3543
-
Jinan Testing Equipment IE Corporation
With over 15 years of proven reliability in the world’s most demanding testing environments, the Model 3543 extensometer is designed to survive in those applications where standard axial extensometers would not. Designed by Epsilon, the Model 3543 was created to survive specimen failure by separating into two halves, thus preventing permanent damage to the module body. During operation, the upper half of the extensometer pulls out of the main body. Tapered measuring beams activate strain gaged flexures within the unit. This unique design allows long measuring ranges, yet retains compatibility with electronics for strain gaged transducers. These models offer high accuracy and are light weight but rugged, with low operating force. They are tension only units.The units have hardened tool steel knife edges. Standard quick attach wires provided with the extensometer work on flat specimens up to 12 x 31 mm (0.5 x 1.25 inch) and on rounds up to 25 mm (1 inch) diameter. Optional quick attach kit wire forms are available for use on larger samples. See Model 3542L for long gauge lengths with smaller measuring ranges.The Model 3543 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
Half Shaft Torque Measurement Systems
-
Advanced Telemetrics International
ATi’s Half Shaft Telemetry System transmits torque signals from rotating shafts to a stationary telemetry receiver. It connects directly to strain gages adhered to the shaft converting it into a torque sensor allowing it to transmit shaft torque while the vehicle is operating. This system is a testing tool used by automotive and racing engineers to obtain real-time torque measurements from vehicle drivelines.
-
Product
Press Force Load Cell
6000 Series
-
Press Force Load Cells are strain gage based transducers for press-force monitoring. This type offers capacities up to 100 kN with compensated temperature performances. Cable is contained within a stainless steel spring for strain relief purposes for additional protection.
-
Product
NI-9219, 100 S/s/channel, 4-Channel C Series Universal Analog Input Module
779781-02
Analog Input Module
100 S/s/channel, 4-Channel C Series Universal Analog Input Module - The NI‑9219 is designed for multipurpose testing. With the NI‑9219, you can measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors, as well as make quarter-bridge, half-bridge, and full-bridge current measurements, with built-in voltage and current excitation. Each channel is individually selectable, so you can perform a different measurement type on each channel.
-
Product
Signal Conditioning Instrumentation
-
Columbia Research Laboratories
Columbia offers a wide variety of Signal Conditioning Instrumentation for a variety of Sensor types. These range from Laboratory as well as Airborne Charge Amplifiers, Differential Charge Amplifiers, In-Line Charge Converters, Constant Current Power Supplies and ICP Compliant Amplifiers all in support of Columbia's extensive Piezoelectric product line. Additionally Columbia offers unique Strain Gage Instrumentation Amplifiers which provide built in auto zeroing of gage offset voltages which can increase typical measurement accuracies. These robust Signal Conditioning products have been flight qualified on many current military aircraft and missile programs and are now available for your distinctive program needs.
-
Product
Button Load Cell
3000 Series
-
Button Load Cells are strain gage based transducers with temperature compensation and excellent overall performance. This type provides a range of capacities up to 150 kN or 30 klb with better than ±0.5% (full scale) non-linearity. Three tapped holes are provided on the underside for ease of mounting. Fully welded cover, amplified and digitised versions are available on request.
-
Product
Miniature Dual Axis Wireless Sensor
-
Advanced Telemetrics International
This custom, miniature, dual axis wireless sensor measures both torque and thrust (axial force). Two super miniature strain gage transmitters, housed within the sensor body, are powered inductively. Onboard sensor excitation and signal conditioning is also contained within the transmitters.
-
Product
Strain Gauge Measuring Instruments
-
It is a Strain Gage Indicator and also function as a Strain Gage Transducer Indicator.As a Strain Gage Indicator, it can support 10 types of bridges and dummies. While if used as a Strain Gage Transducer Indicator, there are 24 bits A/D converts to make the measurement.
