Switch Matrices
See Also: Switch Matrix, Crossbar
-
product
PXI Automotive Switch Simulator Modules
Pickering's Switch Simulator Modules are designed for automotive test applications. These modules simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. They allow automotive I/O devices to be tested for correct operation under adverse conditions.
-
product
Multiport Calibrated Measurements With Switch Instruments
S95553B
This application provides a macro which enables full multiport error correction and measurement capabilities using external switch instruments such as the M9164A/B or M9165A/B PXI Solid-state Switch Matrix. The software includes an easy-to-use measurement wizard that simplifies measurement procedures and reduces the setup time of complicated multiport measurements. The VNA displays measured multiport S-parameters.With the combination of M980xA PXIe VNAs and M916xA/B switch matrix, up to 66 ports (2 VNAs (4 ports and 6 ports M980xA), plus 4 modules of 2x16 M9164A/B) can be configured and supported. Measurement specification is supported when using the M9164B/M9165B 9 GHz switch modules.
-
product
Flexible Data/Analog Switching System
S6025DE
Universal Switching Corporation
Designed for parallel switching of RS-232 data or other similar types of data, the S6025DE delivers compact solid-state switching in an expandable configuration. The unit can start as a smaller size and be expanded later to a full 60x60 array with 25 levels, perfect for switching RS-232 type data. It provides a choice or a combination of remote control including RS-232C, RS-422A, RS-485, GPIB (IEEE-488) and Ethernet (10base-T).
-
product
6U High-Density PXI Matrices
High-density matrices suitable for signal switching in ATE and data acquisition systems.
-
product
Switch Fabric Modules
Switched fabrics provide the interprocess communication backbone for OpenVPX systems - and these modules enable you to achieve the maximum benefit.
-
product
Development Switch
TTESwitch Lab Space
The TTESwitch Lab Space supports laboratory testing efforts of Time-Triggered Ethernet applications; user development costs can be reduced by using the internal TTESwitch Controller HiRel ASIC that is also used in flight equipment. With advanced features like speeds of up to 1 Gbit/s, flexible physical layer configuration and three supported traffic classes, it is the optimal switching solution for a large variety of application areas. TTEthernet is a fault-tolerant, real-time communication protocol for safety-relevant systems integrating Ethernet and TTEthernet data flows onto one physical infrastructure.
-
product
Snap / Toggle Switches
Panasonic Industrial Devices Sales Company of America
A Snap/Toggle Switch is an Operational Switch that is manually operated and can be used to select between ON-OFF states. Snap/Toggle switches are used when an engineer would like a manual circuit control that has simple and reliable operation. Panasonic Snap/Toggle Switches are capable of high capacity switching in a small package size. Panasonic has a variety of Sealed Types for use in different environments with both Rocker and Push-button Actuators available. The terminals are constructed for easy implementation..
-
product
4x2 HDMI Matrix Switch with RS232 Control
HSM-04-02
4x2 HDMI matrix switch with RS232 control. Supports HDCP, deep color, multi-channel digital audio (up to 7.1 channels), and may be used with any combination of DVI (PC) or HDMI (HDTV) sources and displays.
-
product
LXI Optical Switching - 4x4 Matrix Plugin Module
65-280-321
The 65-280-321 4x4 matrix is part of the 65-280 and 65-281 ranges of optical plug-in modules offering matrix & insert/bypass or multiplexer & SPST topologies respectively with all models based on MEMS fiber optic switches and available in various populations per plugin. In addition, a choice of different connector styles to suit most applications is offered: FC/APC (for optimal performance), FC/PC, SC/PC and ST for general applications and LC for high density applications. They use MEMS (Micro-Electro-Mechanical-Systems) based optical switches to route signals between terminals by redirecting the optical signal. This is achieved using micromechanical mirrors driven by a highly precise mechanism activated via an electrical control signal.
-
product
Programmable Limit Switch (PLS)
AMETEK Sensors, Test & Calibration
The Gemco Programmable Limit Switches (PLS’s) are used in a variety of applications from packaging and stamping to every day factory automation. In the Heavy Moveable Structure Industry, they can typically be found in Rail and Draw Bridge Control Houses. These devices are typically found in applications where the PLC scan time cannot keep up with the process.
-
product
Network Switches
Electro Standards Laboratories
Our switches support a variety of applications including Automatic Fallback, Process Control, Telco, TV&Radio Broadcasting, Video Surveillance Systems and More. We have hundreds of designs available online, but if you can't find exactly what you are looking for, we can assist.
-
product
PXI Single 64x4 Matrix 1-Pole Switching
40-533A-021
Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability sputtered Ruthenium reed relays, offering >109 operations to give maximum switching confidence with long life and stable contact resistance.
-
product
PXI Solid-State Switch Module, 6xSPST, 1.5 A, 400 V, Hardware Interlock
40-185A-001-HI
The 40-185A-001-HI has 6-off high current SPST switches with hardware interlock in two PXI slots and is part of our range of high power solid state switching solutions.
-
product
PXI Hex SPDT RF Switch MCX 75 Ohm
40-830-106
The 40-830-106 is a 75Ω RF Switch with 6 separate SPDT relays in a single PXI slot. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks have been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
product
Optical Switches
Nanning Xionghua Photonics Technology
Optical Switches by Xionghua Photonics
-
product
PXI Dual 12x4 Matrix, 2 Pole Switching
40-511-022
The 40-510 series of matrix modules feature a wide range of selectable switchingconfigurations (12x4,dual 12x4,12x8 and 24x4). Typical applications include signalrouting in ATE and data acquisition systems.Available reed relay formats are 1-pole, 2-pole and 1-Pole screened. The screenedversion is suitable for switching signals up to 50MHz. Larger matrices may be constructedby Daisy Chaining the common signals from multiple PXI modules.
-
product
Dynatrol® Sealed & Suspended Level Switch
The Sealed and Suspended Dynatrol® Detector is designed for high point level detection of bulk solids. For problem applications, such as those associated with angle-of-repose, this configuration provides reliable operation in hard to reach locations.
-
product
34945EXT Distribution Board, For Two 87222, L7222C Transfer Switches And Six N181x SPDT Switches
Y1154A
The Y1150A-Y1155A distribution boards enable simple connections to the external switches. The distribution boards plug onto the 34945EXT and are used to route the power and control signals from the driver module to the switches using standard cables.
-
product
eBIRST™ – Switching System Test Tools
The eBIRST toolset consists of four different tools that support 200-pin LFH, 104-pin, 78-pin and 50-pin D-type connectors and a set of adaptors that allow connection to other connector types. A supplied application program controls the eBIRST tools via a USB2 port that also provides the tool power and controls the switching system using a Test Definition File to define the test sequence.
-
-
-
product
Terminal Block For The 34939A 64-Channel Form A Switch
34939T
This terminal block is used for discrete wiring. A fully loaded terminal blocks supports up to 20 AWG wire size typical and 18 AWG max. This terminal block has screw terminal connections.
-
product
LXI Optical Switching
LXI is an ideal platform for supporting optical switching systems; the use of Ethernet control makes it easy to provide optical switching within the network that is easy to control via a programmatic or web based interface. MEMS switch technology offers higher performance and longer operational life compared to conventional prism based optical switching.
-
product
Airspeed Warning Switches
Supply Voltage: 10÷30 Volts DC Current Rating: 200 mA max Switching Power: 5 A max 30VDC Temperature Range: -40° C to 120° C Pressure Fitting: 1/8" plastic Weight: 3.2 oz.
-
product
PXI Matrix Switch Modules
PXI matrix switch modules deliver low, medium and high-density switching of multiple channels in a single instance. They are organized in rows and columns to provide maximum flexibility, allowing you to connect any row to any column, making them ideal for routing multiple signals between your device under test and your instruments.
-
product
SP2T RF Pin Diode Switches To 18 GHz
Pulsar Microwave's 2-way switches are available in absorptive and reflective designs from 20 MHz to 18 GHz. They are also referred to as single pole, double throw and abbreviated SPDT or SP2T. These switches have a typical VSWR performance of 1.6:1 or better and input power handling of 200 milliwatts maximum. Switching time is 100 nanoseconds, and isolation of 60 dB or greater for most models. Supply voltages are +5V and -5V, with TTL logic control voltage of 0 to 5 volts.Both absorptive and reflective SPDT switches are packaged into Pulsar Microwave's SW2 outline. Configuration is standard with SMA female connectors. Voltage is applied with wire wrap feed thru terminals. The housing serves as electrical ground, and two turret terminals are installed for wiring.
-
product
Multiport Coaxial Switch, DC to 26.5 GHz, SP4T
87104C
The Keysight 87104C multiport switch improves insertion loss repeatability and isolation, which is necessary for higher performance test systems. The repeatability and reliability of this switch is vital to ATS measurement accuracy and can cut the cost of ownership by reducing calibration cycles and increasing test system up time. The Keysight 87104C terminated multiport switch provides the long life and reliability required for automated test and measurement, signal monitoring, and routing applications. Highly repeatable switching capability is made possible through Keysight's rigorous design and tight manufacturing specifications. Low insertion loss repeatability reduces sources of random errors in the measurement path, which improves measurement accuracy.
-
product
Ethernet Switches
Schweitzer Engineering Laboratories, Inc.
Ethernet switches provide LAN connectivity in substations, large enclosures, and industrial plants.
-
product
Gigabit EdgeSmart PoE+ Switch
8 x Gigabit PoE+ ports64W PoE power budgetEasy-to-use web-based management interfaceSupports LACP, RSTP, VLAN, QoS, and IGMP SnoopingVoice VLAN for VoIP applicationsBandwidth control per port16Gbps switching capacityIEEE 802.1p CoS with queue scheduling supportCompact fanless designWall mountable metal housing
-
product
RGB/YUV Passive Video Switch
SWP4031
MicroImage Video Systems? Passive Video Switch line addresses the needs for basic and affordable video switching applications. Each switch is manufactured with a durable aluminum case. A rotary switch mounted on the front is used for selection.
