Switch Matrices
See Also: Switch Matrix, Crossbar
-
product
PXI Single Transfer Switch 18GHz 50Ω SMA
40-782-521
The 40-780 Microwave switching module consists of one, two, three or four changeover switches capable of switching frequencies to 18GHz (optionally to 67GHz) in 50Ω or 2.5GHz in 75Ω. The 40-782 module consists of one or two microwave transfer switches. It has a characteristic impedance of 50Ω and is available in versions with maximum operating frequencies of 18GHz, 26.5GHz or 40GHz.
-
product
RF Switch
DSW9-8R0-18G-2035
RF Switch, DC~18000MHz, SP8T, Programmed Switch, SMA Female, RJ-45, RS-232, GPIB Control
-
product
Pressure Switches
Whitman controls offers the most diverse selection of pressure switches in the industry. Our diverse line of switches are used across a wide range of applications including blowers, generator sets, off-road vehicles, compressors, wafer ovens, process equipment, flow control devices, pumps, wastewater, heating and cooling systems, and numerous other applications across industries.
-
product
Speed Switch
SCP1000/SCP2000
Features• Internal sensor• Over-or under-speed config., 1-990 rpm• 1 DPDT relay output (SCP1000), 2 SPDT relay outputs (SCP2000)• Built-in start delay• Dial-in calibration does not require power• 115, 230 VAC (50-60 Hz) and 12, 24 VDC power options• Works with Electro-Sensors magnetic pulser discs / wraps• Explosion proof housing• UL Listed Class I, Div I (C, D) Class II, Div I (E, F, G)
-
product
Low-leakage Switch Mainframe
E5250A
The Keysight E5250A low-leakage switch mainframe expands a single measurement station, such as the Keysight B1500A, 4155C, or 4156C, to an automated measurement system. Plug-in modules can be configured either as a cross-point matrix for general parametric measurements or as a multiplexer for long-term reliability measurements.
-
product
6U High-Density PXI RF Matrices
Pickering's 6U high-density matrices are suitable for switching frequencies to beyond 250MHz. The 45- 720A module is available in 50 and 75 Ohm versions with a choice of coaxial connectors. It is intended for the easy construction of high-performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture - this maximizes isolation and RF performance.
-
product
PXI Dual Transfer Switch 40GHz 50Ω SMA-2.9
40-782-542
The 40-780 Microwave switching module consists of one, two, three or four changeover switches capable of switching frequencies to 18GHz (optionally to 67GHz) in 50Ω or 2.5GHz in 75Ω. The 40-782 module consists of one or two microwave transfer switches. It has a characteristic impedance of 50Ω and is available in versions with maximum operating frequencies of 18GHz, 26.5GHz or 40GHz.
-
product
Semiconductor Switching Systems
Keithley 700 Series
The high speeds and low currents of semiconductor devices demand high quality, high performance switching of I-V and C-V signals. We offer switching solutions for both semiconductor R&D and production test applications with mainframes that can support up to 2,880 channels and a family of matrix cards designed specifically for semiconductor applications.
-
product
Ethernet Switches
The switches CXR Carrier Ethernet CE 2.0 allow easy and economical transition to 10 Gigabit Ethernet class operator while providing hardened features in temperature and electromagnetic immunity.
-
product
Switch Testing Machines
Educated Design & Development, Inc.
1 or 3 actuating device(s) for rocker switches and push- button switches with 2 single-acting pneumatic cylinders each, with air throttle valves to adjust the actuating speed, height-adjustable mounted to holders, with multiple adjustable specimen holders, with safety sockets to connect the specimens to external test voltages and loads1 housing, made of steel, with protective hood1 plug-in unit with front panel for operating the devices.1 Control device for the entire unit:main switch with EMERGENCY OFF function, safety switch for the protective hood, mains cord and fuses1 control device for each actuating device:programmable control unit with exchangeable program modules (containing the "test rhythm") and for adjusting and indicating the test parameters "number of strokes" and "stroke time", start and stop push-buttons, push-buttons for moving manually the cylinder pistons and as actuation indicator for the cylinder
-
product
PXI/PXIe RF Switch, Quad SPDT, Terminated, 8GHz, 50Ω, SMA
40-880B-002
The 40-880B-002 (PXI) and 42-880B-002 (PXIe) are quad SPDT 50Ω RF switches with 8GHz bandwidth. The 40/42-880B range has automatic termination of unused signals and are available as a dual switch in 1 slot, a quad switch in two slots or hex and octal switches in three slots.
-
product
What is an SPST Switch?
Learn more about SPST switches. A Single Pole Single Throw (SPST) switch is a switch that only has a single input and can connect only to one output. This means it only has one input terminal and only one output terminal.Learn more on What is an SPST switch at Precision website here.
-
product
NETernity Ethernet Switch
RM984RC
The RM984RC delivers full wire-speed 10/100BaseTX Ethernet Layer-2 switching on all ports. It is available in three models including air-cooled commercial temperature; air-cooled industrial temperature, and conduction-cooled.
-
product
Mechanical Pressure Switch For Air
APE/APS
A lineup of mechanical pressure switches, modular type and single unit specifications.
-
product
Vacuum Switch Tester
Weshine Electric Manufacturing Co., Ltd
1. The instrument has an automatic measurement function.2. The instrument has a perfect back-EMF protection function.3. The instrument uses a 5-inch 65K color LCD touch screen, which is easy to operate.
-
product
Switching Power Supplies
PeakTech Prüf- und Messtechnik GmbH
A type of power supply that works by switching current into a high-frequency transformer or inductor at frequencies much higher than the input or line frequency
-
product
OEM Gas Pressure Switch
1996
Reliable and convenient, the 1996-5 and 1996-20 Gas Pressure Switches serve as a compact, low cost switch for gas fired furnaces and equipment. Pressure ranges for both models are ideal for high or low gas pressure interlock. Visible set point and on-off indicators add convenience in servicing
-
product
Linear Actuators DPDT Switches
DPDT
Most Thomson actuators require at a minimum the use of a double-pole double-throw remote switch. To better assist our customers, we provide two versions of a DPDT switch (with or without enclosure) to work directly with our actuator units. A wiring diagram label and an "OFF" center position are included.
-
product
Diaphragm Operated Pressure Switch
1000E
Extremely rugged construction provides excellent reliability in chemical, petroleum and industrial plants. Bellville spring movement permits mounting of control in any position and helps prevent contact chatter. new design also provides high overpressure protection. Available with standard weatherproof housing to meet NEMA-1 through 4X and NEMA-13, JIC.
-
product
Network Optical Channel Switch
NOCS
NOCS ( Network Optical Channel Switch ) is a kind of tool with one or more optional transmitting ports. Its role is to switch or logically operate optical transmission line and the congregation of optical signal, simply means that you can use a optical fiber which is connected to a port and use it to connect to more ports by NOCS switch.
-
product
Switching Controller & PWM Controllers
Renesas offers a broad portfolio of switching and pulse-width modulation (PWM) controllers optimized to provide high efficiency across the entire load range. The portfolio is comprised of single, dual, triple and quad output controllers with integrated drivers and either voltage- or current-mode architecture.
-
product
Ethernet Mezzanine Switch
P/XMC-651
Curtiss-Wright Defense Solutions
The XMC/PMC-651 is a 12-port Gigabit Ethernet switch packaged in the industry-standard XMC form factor. It is designed to support "in-chassis" networks with managed Layer-2 switching capabilities.
-
product
Multiport Switches
These multiport switches can be used in many different applications. The switches allow a single input and multiple (three or more) output paths. The single-pole double-throw (SPDT) switch is a subset of the multiport switch.
-
product
UltraCMOS SP8T RF Switch
PE42582
The PE42582 is a HaRP™ technology-enhanced absorptive SP8T RF switch that supports a frequency range from 9 kHz to 8 GHz. An external VSS pin is available for bypassing the internal negative voltage generator in order for the PE42582 to deliver spur-free performance. It delivers high isolation, low insertion loss and fast switching time, making this device ideal for filter bank switching and RF signal routing in test and measurement (T&M) and wireless applications up to 8 GHz. No blocking capacitors are required if DC voltage is not present on the RF ports.
-
product
Buffered Analog Crosspoint Switches
Analog Devices buffered video crosspoint switches offer multiple configurations from 8x8 up to 32x32 channels with gain of 1 or 2 and are offered in LQFP, LFCSP, and BGA packages. These crosspoint switches can be programmed either in serial or parallel modes and are used primarily for routing high speed signals, including composite video (NTSC, PAL, SECAM) and component video (YUV, RGB) in applications such as studios, video on demand, in-flight entertainment, surveillance, and video teleconferencing.
-
product
Key Selector Switch
SG-D1
Panasonic Industrial Devices Sales Company of America
Key Selector Switch with direct open operation function and pin tumbler design for high security.
-
product
PCI Express Passive Switches
MAX4888A
High-Speed PCI Express Passive Switches Enable Gen II Switching
-
-
-
product
Amplifier, Switch and Test Box
CLIOQC Model V
The QCBOX Model 5 is a non-conventional unit designed to fulfil actual and future needs of an electro-acoustical analyzer like the CLIO system. It is USB linked to a PC and can be configured, with dedicated software controls, to assist frequency response and impedance measurements or to perform DC measurements. Using it for frequency response measurements acts as 50W power amplifier to drive the speaker or network under test while routing one-of-four inputs to the analyzer as well the current sensing output. The four inputs are able to provide a phantom power supply both for Audiomatica or general purpose microphones (0-24 V range, software controlled). Impedance measurements can be done either switching the D.U.T.’s load across the analyzer’s input or using a dedicated output, ISENSE, thus allowing impedance measurements in constant voltage mode as well voice coil current distortion analysis. An internal ADC measures the DC current into the voice coil. Thanks to an internal software controlled voltage generator the speaker can be driven with a superimposed DC voltage (±20V), allowing for measurements of large signal parameters. Two ADC converters with a ±2.5 V and ±5 V are available at inputs 3 and 4 to measure the displacement with a laser sensor or any other DC signal. A dedicated digital input handles an external foot pedal switch (or TTL signal) to be connected and triggers QC operations. A 6 bit output – 5 bit input TTL digital port is available to interface the QCBOX and driving software with external hardware (like turntables for example).The QCBOX Model 5 finds use both in laboratory for R&D applications and in production lines setups.
