Discrete Component Testers
check connected individual semiconductor components.
-
Product
Programmable Parametric Tester For Discrete Semiconductors
IST-8800
-
IST Information Scan Technology, Inc.
The IST-8800 is a fully programmable, low cost tester that provides parameter measurements or parametric GO/NO GO test for transistors, diodes, MOS-FETs, Regulators, Triacs, Zeners, SCRs, and J-FETs. These devices can be tested up to 5 amps or 1200 volts with a measurement range down to the nano amp range. Only four universal test fixtures are required which can test the device across a wide range of packages.
-
Product
Design and Development: Complete Systems and System Components
-
Custom Systems Integration Inc.
CSI''s design and development (D&D) organization has the resources, skill and experience to design a complete turnkey system, a system component or collaborate with customer''s internal staff on any part of a system.
-
Product
ITA, 9050, 50 Module, VXI and Discrete Wiring, Double Tier
410104538
ITA
The 50 module ITA can be used in a number of applications to accomplish the required connection to the Unit Under Test (UUT). You can mount a VPC front or rear mount enclosure or customize your own fixture to be attached on the frame. A wide range of ITA modules are available separately for user configuration.
-
Product
Hydraulic Component Test Stand
Model 700
-
Model 700 Hydraulic Component Test Stand (HCTS). Designed to test heavy-duty, off-highway, closed or open loop pumps, the 700 gives you the capacity to confidently and efficiently verify the quality of your work. Test new or rebuilt pumps, motors, valves, and cylinders independently, and communicate their quality to your customers with the help of PowerNet TD, data acquisition software for transmission and hydraulic systems. Convenient work height with adjustable mounting track. 100, 200 or 300 HP drive motor options available. Variable Frequency Drive (VFD) controlled drive motor. 200 gallon (757 L) high-mount hydraulic oil reservoir for flooded pump supply. Combined kidney filtration and cooling loop for continuous cleaning. Thermostatically controlled cooler and 7 kW reservoir immersion heater.
-
Product
Passive Component
-
Shanghai Tarluz Telecom Tech Co., LTD
An electronic component which can only receive energy
-
Product
32-CH Discrete Input Modules
HSL-DI32-M-N/HSL-DI32-M-P
Digital Input Module
- Slave ID consumption: 2 consecutive from odd- "N" type for NPN sinking type sensor or dry contact; "P" type for PNP sourcing type sensor or wet contact- Photo couple isolation voltage: 2500 Vrms- Input impedance: 4.7 KΩ- Input current: ± 10 mA (Max), ± 12.5 mA (Peak)- Input voltage: ± 40 V (Max)- LED indicator: Power, Link and Input status- Power supply: +10 V to +30 VDC
-
Product
Test Connector Components
-
Any flat substrate, or bumped substrate, can be compressed against Z-Axis Elastomeric Connectors to make contact. The picture illustrates a Z-Thru Z-Alloy Connector Frame used to connect the DUT (Device Under Test) to a circuit board.
-
Product
Hi-Speed Discrete Test System
QT-6000
-
QT-6000 Test System, with built-in capacitance test (DC+CAP) and Scanbox etc, is applicable to devices like medium & small power transistors, MOS-FET, diodes and Wafer.
-
Product
Component Test Fixture For N1413 With B2980 Series
N1428A
Test Fixture
The N1428A is designed to operate specifically with the B2985B / 87B electrometer / high resistance meter. It is provided with two component modules, which are used to hold SMD, lead, and various types of devices. Electrical noise effects are reduced by the employment of a shielded case. A built-in interlock circuit enables safe high-voltage measurements. The N1413A high resistance meter fixture adapter is also required to connect the N1428A to the B2985B / 87B.
-
Product
RF Components
-
Passive RF components from MegaPhase cover a wide range of frequencies, power levels and applications. MegaPhase offers a variety of directional couplers, power dividers/combiners and quad hybrids in narrow band and ultra-broadband designs ranging from 0.5 MHz to 46 GHz. The in house engineering team brings decades of experience and knowledge designing and manufacturing RF components for military, commercial and space applications.
-
Product
Line Tester
LT51
-
The LT51 Line Tester is a portable handheld battery powered instrument for Data, DSL, Telephone, Voice Copper Line testing. It combines the features of several pieces of test equipment such as a Level Meter / Spectrum Analyser, Distortion Analyser, Oscillator, Handheld DMM and TDR in the one small lightweight package.
-
Product
Wafer Tester
-
Tokyo Electronics Trading Co., Ltd.
A vital step in the Semiconductor Value Stream, focusing on electrical screening and consumption of Known Good Die (KGD).
-
Product
Energized Tester
ALL-SAFE PRO
-
Conduct safe, easy and accurate ESA testing in only 60 seconds with the ALL-SAFE PRO® motor connection box. The ALL-SAFE PRO® is a permanently installed connection accessory for the ATPOL III™ energized testing instrument. With this electric motor connection box, the ATPOL III™ can perform tests easily with a quick disconnect.
-
Product
Snap Tester (Button Pull Tester)
TF145
-
TESTEX Testing Equipment Systems Ltd.
Snap Tester (Button Pull Tester), to determine the holding or breaking strength of prong-ring attached snap fasteners onto garments or toys, also as a Push Pull Tester for compression and tensile testing of small samples(special attachments are available).
-
Product
Ethernet Tester
GAOTek Gigabit
-
GAOTek Gigabit Ethernet Tester is a handheld tester for installation, commissioning and maintenance of 10M/100M/1000M ethernet networks. By combining network performance test & monitoring, data packet sniffing, traffic generation, cable test and BER test in one unit. It is widely used in testing BER of layer 1, layer 2, layer 3, and full-featured RFC-2544 and Y.1564 testing. It can help the front-line field technicians analyze the network quality and locate the fault rapidly.
-
Product
Installation Testers
-
Safety and performance are two of the most critical requirements for any electrical system. Good quality insulation, a properly working grounding system and active protection assure the safety of people, electrical systems and buildings, and protect them against electrocution, fire and other equipment damage.
-
Product
Measurement Components
-
Rosenberger Hochfrequenztechnik GmbH & Co. KG
Innovative developments and modern electronic applications to support everyday life require the use of ever higher frequencies – this applies to specialized areas such as aerospace technology and automotive as well as to the increasing bandwidth requirements in communications technology.
-
Product
Semiconductor Testers
-
Designing and manufacturing scalable Automated Test Equipment (ATE) targeted at testing SOC, MCU, RF PA/FEM, Sensors/MEMS and Power and Analog devices
-
Product
Tackiness Tester
TAC1000
-
For the measurement of tackiness (instantaneous adhesive strength) of various pastes and adhesive tapes, it is possible to quantitatively evaluate the data, which until now had large errors due to individual differences. First, press the measuring probe, which is controlled (approach speed, pressure force, pressure time, separation speed) against the sample, and measure the adhesive force in the process of separating. Measured data can be processed by a computer. With double temperature control (patented), the sample piece is preheated from the back side with a hot plate and the heated probe penetrates the measurement surface, making it possible to keep the set temperature and the temperature of the test surface to be evaluated constant. Since the pressurization time can be as short as 10msec, it is possible to measure the tackiness caused by momentary contact.
-
Product
ESD Tester
GZ600 MIF
-
• Staff equipment tester with badge reader • Compact • LCD digital display • Identification by RFID badge • Allows communication with the company network or the dedicated server (SQL database)
-
Product
CCTV Tester
M-IPC-200A
-
Fuzhou Metricu Technology Co Ltd
3.5 inch IP camera tester M-IPC-200A with analog, HD-TVI, HD-CVI, AHD
-
Product
Environmental Testers
-
AEMC manufactures a line of cost effective, hand-held instruments for measuring temperature, humidity, light, wind speed and other variables. Each instrument in this series includes sensor, backlit CD and a shockproof holster. They are battery operated and can easily be carried in a shirt pocket.
-
-
Product
CT Tester
6000 Bird Dog Plus
-
Spinlab Utility Instrumentation, Inc.
This new and exciting true 3 phase Bird Dog Plus enables you to determine the accuracy of any meter in the field--from Form 1 through Form 17. Electronic sensors allow you to automate the test to gain the highest possible accuracy. The process is fast, simple, and much less expensive than a portable test board for the meter test and still perform ratio & burden tests on your CTs (CT Tester).
-
Product
X-Ray Components
-
Photonis designed the Micro Pore Optics detector to be used in X-Ray imaging applications. Its perfectly square, flat channels are optimized to allow X-Ray and UV photons to be focused or collimated due to the total external reflection at a grazing angle (<2°). Micro Pore Optics are installed on a number of international space missions.
-
Product
Scratch Tester
CSR1000
-
This tester is highly effective in measuring the adhesion strength (adhesion strength) of hard coatings (Ti, TiN, SiC, DLC, etc.) formed by PVD and CVD on metal surfaces such as cemented carbide. Adopting a scratch test method that allows quantitative measurement with simple operations, the film surface is scratched while increasing the load on the sample surface, detecting film breakage with high sensitivity, and providing the load at which film breakage occurs (critical load). tools and mold tools that require
-
Product
Tearing Tester
TGT-01
-
Jinan Leading Instruments Co., Ltd.
TGT-01 Tearing Tester is applicable in thetearing test of films, sheets, flexible PVC, PVDC, waterproof films, wovenmaterials, polypropylene, polyester, paper, cardboard, textile and non-woven,etc.
-
Product
Wound Component EST Scanner
19035
-
The quality verification tests for wound components consist mainly of AC/DC Hipot tests and insulation resistance (IR) tests. The Chroma 19035 wound component EST scanner series perform safety tests for motor, transformer, and heater related wound products.
-
Product
Insulation Testers
AD-902
-
The instrument is designed for the direct measurement of insulation resistance of cables and electrical equipment especially in the telecommunications and communications. It can also serve as a tester for example go. Circuits or connectors.
-
