-
Product
DC Power Module, 100 V, 0.5 A, 50 W
N6736B
-
The N6736B is a one-slot 50 W programmable DC power module for use in the N6700 low-profile Modular Power System or N6705 DC Power Analyzer.
-
Product
Electron Microscope Analyzer
QUANTAX WDS
-
The QUANTAX WDS (WDX) for SEM consists of the XSense wavelength dispersive spectrometer yielding the best resolution among all parallel-beam WDS systems.
-
Product
RF PHY Tester
TLF3000
-
TLF3000 RF PHY tester is a wideband, ultra-high dynamic range 2.4 GHz software-defined receiver, signal analyzer and signal generator. It captures and analyses the entire 2402-2480 MHz band simultaneously providing RF PHY testing, signal generation, signal analysis in one powerful package.
-
Product
Low Cost Emulator
EB-XAG49
-
* Emulates P51XG49 Microcontrollers * Real-Time Operation up to 30MHz * 3.3V or 5V Voltage Operation * Source-Level Debugger for C and Assembler * MS-Windows Debugger Software * Reduced Set of C-Compiler and Assembler * Support for ROMless and ROMed Microcontrollers * 64K of Code Memory * Performance Analyzer * Real-Time and Conditional Breakpoints * 44-pin PLCC Emulation Header and Signal Testpoints * Serially Linked to IBM PC at 115 Kbaud
-
Product
MIL-STD-1553 Test & Simulation Interface for PCI Express
PCIe-C1553
-
Avionics Interface Technologies
Dual redundant, single, dual or quad stream configurationsSoftware selectable Transformer, Direct, and Bus Stub Coupling Modes - Concurrent Bus Controller, 31 Remote Terminals, & Bus monitor operation - Full error injection and detection - Multi-level triggers for capture and filtering - Ten high voltage (up from 30V) programmable DIO lines - IRIG-B time code encoder/decoder with free-wheeling mode - Real-Time recording and physical bus replay - x1 Lane PCI Express Host Interface (x4 Physical edge connector) - Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
110 GHz Frequency Extender
N5293AX53
-
The N5293AX53 modules are compact lightweight modules designed to interface to the N5292A test set controller that is driven with a PNA/PNA-X B model vector network analyzer.
-
Product
8-Channel 250 MHz A/D Jade XMC Module w/ 72 DDCs for Defense & Radar Phased-Array Applications
-
member of the Jade" family of high-performance data converter XMC modules based on the Xilinx Kintex Ultrascale FPGA. The Model 71132 is an XMC module featuring eight 250 MHz 16-bit A/Ds with eight wideband digital down converters (DDCs) and 64 multiband DDCs, all fully programmable. The Model 71132 doubles the number of A/D channels and DDCs over previous models giving this the best price per channel ratio in the product family. Applications monitoring a broad spectrum with a need to quickly analyze specific portions of the identified spectrum can greatly benefit from the capabilities of the 71132.
-
Product
Automatic Calibration Module
ACM4520
-
ACM4520 is an automatic calibration module that can be used with all CMT Vector Network Analyzers operating in frequency range up to 20 GHz. It is a fully automatic USB-controlled and powered electronic calibration module. Minimizing the number of steps required by technicians reduces the risk of human error and expedites the calibration process.
-
Product
Cable & Satellite
-
Vector network analyzers are a valuable tool for broadcast engineers. VNAs enable users to perform an array of measurements including cable loss, return loss, VSWR, distance to fault, and time domain. CMT’s USB VNAs help broadcasters extend their reach and easily perform maintenance in the field or in the shop.
-
Product
Smartchem Discrete Analyzers
-
Fully automated, multi-parameter, direct read discrete analyzers, available in bench-top or floor-stand models, for simple and automated chemistries. Up to 200 samples and up to 600 tests/hour.
-
Product
100 amu CIS Analyzer
CIS300
-
Stanford Research Systems, Inc.
With better than 1 ppm detection limit, direct sampling at mTorr pressure, and a user-friendly Windows software package, the CIS systems will satisfy your most demanding applications. On-line process monitoring and control, verification of process gas purity at the point of use, high-vacuum residual gas analysis, and process equipment leak checking are some of the areas where these systems will prove indispensable
-
Product
DC Power Analyzer, Modular, 600 W, 4 Slots
N6705C
-
The N6705C DC Power Analyzer provides unrivaled productivity gains for sourcing and measuring DC voltage and current into the DUT by integrating up to 4 advanced power supplies with DMM, Scope, Arb, and Data Logger features. The N6705C eliminates the need to gather multiple pieces of equipment and create complex test setups including transducers (such as current probes and shunts) to measure current into your DUT. The DC Power Analyzer also eliminates the need to develop and debug programs to control a collection of instruments and take useful measurements because all functions and measurements are available at the front panel. For even greater control and analysis functions, the DC Power Analyzer can be used with the 14585A Control and Analysis Software. When automated bench setups are required, the N6705C is fully programmable over GPIB, USB, LAN and is LXI Compliant. 14585A Control and Analysis Software
-
Product
Keysight Quad 1x4 75 Ohm 1.5 GHz Multiplexer Module for 34980A
34942A
-
The Keysight 34942A RF multiplexer module for the 34980A Multifunction Switch/Measure Unit offers bi-directional switching broadband signals. High channel isolation ensures quality dynamic range measurements with your oscilloscope, spectrum analyzer, or other instrumentation.
-
Product
Neutron Pulse Monitor
NPM-2000
-
The QI NPM-2000 is a programmable Neutron Pulse Monitor with integrated high voltage supply and multichannel analyzer (MCA) designed for use with Helium-3 (3He), Boron-Trifluoride (BF3), and Boron-10 (10B) lined proportional neutron detectors. Designed for ease of use, operating parameters are digitally configured. Signal pulse height spectra produced by the Neutron Pulse Monitor aid in setting discriminator levels and provide valuable diagnostic information on system health.
-
Product
Trash Analyzer
TB500
-
TESTEX Testing Equipment Systems Ltd.
Cotton Trash Analyzer, to analyses lint, trash and dust content within a sample of raw cotton fiber up to 100 grams. Also used to determine non-fiber content of synthetic fibers and to open and clean fibers for further testing. The analyzer uses the carding principle with air separation of lint and non-lint content.
-
Product
Analyzers and Timers
CAT Advanced Series
-
Description The Advanced CAT Series Analyzers and Timers are stand-alone or PC-controlled digital instruments for circuit breaker status evaluation. Timing channels record arc closing and opening, resistance and auxiliary contacts. The main contact channels can also measure the resistance value of pre-insertion resistors (if present in the breaker). The advanced CAT series records graphs of the opening and closing coil currents and the movements of the moving parts of the high and medium voltage circuit breaker. Test results are printed on the 112 mm (4.4 inch) thermal printer (optional accessory) in tabular and graphical form. The advanced CAT series provides easy selection of different operating modes:
-
Product
Ambient Metal Analyzer
AMMS-100 XRF
-
The system integrates X-ray fluorescence for metal analysis up to 30 elements and a beta-ray attenuation model for particulate mass monitoring. But module will be using the same sample moving sequentially across the detector and would be significantly effective in industry emission tracing.
-
Product
Probes & Flow Cells
-
The sample interface is a virtual “windows into the process” and is a critical component of any optical analyzer system. Guided Wave sample interfaces (probes, flow cells) are designed for use with NIR or UV/Vis fiber optic coupled analyzers. They are designed to be rugged and reliable in harsh chemical and physical process conditions while providing optimal transmission for long-term reliable measurements.
-
Product
Semiconductor Device Parameter Analyzer and Measurement Modules
B1500A Series
-
Keysight B1500A Semiconductor Device Analyzer of Precision Current-Voltage Analyzer Series is an all in one analyzer supporting IV, CV, pulse/dynamic IV and more, which is designed for all-round characterization from basic to cutting-edge applications. It provides a wide range of measurement capabilities to cover the electrical characterization and evaluation of devices, materials, semiconductors, active/passive components, or virtually any other type of electronic device with uncompromised measurement reliability and efficiency. In addition, the B1500A’s modular architecture with ten available slots allows you to add or upgrade measurement modules if your measurement needs change over time.
-
Product
Logic Analyzer
FS2352B
-
The FS2352B is a logic analyzer probe used to test DDR3 DIMM memory. When used with the triggering and analysis capabilities of Keysight’s Logic Analyzer modules, it gives the user an effective tool for debugging, testing and verifying DDR3 DIMMs. This logic analyzer probe has a CKE qualification circuit that allows for the use of older Keysight logic analysis modules when testing systems using power saving modes.
-
Product
Heated Type NOx Analyzer
MEXA-1170HCLD
-
The MEXA-1170HCLD is available as an atmospheric (A) and a vacuum (V) model. With nine ranges available from 10 ppm up to 10,000ppm, these instruments are designed to fit most applications in the industry.
-
Product
PV Analyzer I-V Curve Tracers
-
The Solmetric line of PV Analyzer I-V curve tracers are widely used in Commissioning, Auditing, O&M, and Troubleshooting of PV systems.
-
-
Product
Shock Tester
DP-1200
-
King Design Industrial Co., Ltd.
Shock or bump test mainly simulate the impact effects of product and its components encountered in usage and transit process. Through standard and high-reproducibility instant energy exchange, you can analyze the product ability to tolerate the strong external stress and the degradation of structural weaknesses to quickly obtain the data of structure strength, anti-shock appearance and anti-drop. Shock tester is one of destructive experiments, and do destructive test on the product to evaluate the product reliability and monitor the consistency of production line.
-
Product
Test Program Management
TP-M
-
TP-M utilizes TestInsight unique capability to read and analyze a whole test program from flow to every test pattern, timings, levels etc.
-
Product
WDXRF Wafer Analyzer
2830 ZT
-
The 2830 ZT wavelength dispersive X-ray fluorescence (WDXRF) wafer analyzer offers the ultimate capability for measuring film thickness and composition. Designed specifically for the semiconductor and data storage industry, the 2830 ZT Wafer Analyzer enables the determination of layer composition, thickness, dopant levels and surface uniformity for a wide range of wafers up to 300 mm.
-
Product
PXI Vector Network Analyzer, 9 kHz to 9 GHz
M9802A
-
Full 2/4/6/ port VNA on a PXI module with flexible applications.
-
Product
Handheld Digital Spectrum Analyzer,
109990014
-
RF Explorer is a handheld digital spectrum analyzer, a very affordable tool for work in all ISM popular frequency bands. It is based on a highly integrated frequency synthesizer which offers high performance, compact size, low consumption and low cost.
-
Product
Optical Backscatter Reflectometer
OBR 4600
-
The Luna OBR 4600 Optical Backscatter Reflectometer (OBR) is a powerful tool for testing and analyzing loss in short-run networks and components. The OBR 4600 is an ultra-high resolution reflectometer that features a spatial sampling resolution of 10 microns, zero dead zone, and backscatter-level sensitivity. The OBR 4600 offers industry leading technology to precisely track loss and polarization states, allowing you to “see inside” your components and systems.
-
Product
Compact Protocol Analyzer
LE-1500R
-
"LE-1500R" is a protocol analyzer (line monitor) dedicated for asynchronous communication monitoring with affordable pricing. LE-1500R can run as a stand- alone by the internal battery for long time and can be remotely controled by a PC or a smart phone via Wi-Fi (Wi-Fi function is available only in USA, Canada, Japan, and EU). The analyzer has a TTL measurement port (which supports UART communication) as its standard port besides RS-232C, RS-422, and RS-485. It can monitor communication data of max 500Kbps for up to 32MB (8,000,000 data) in real time and also can execute a simulation testing of send/receive data. It also has a BERT function (which is not equipped with the analyzers of this pricing level) as its standard function. The correct time stamp, the measurement of idel time (which are the difficult for other software analyzers), and the capturing ability (without missing data) are the best options for trouble shooting and development test of a communication sytem which requires a reliablity.
