-
Product
RF & Microwave Modules for 34980A
-
The Keysight RF and Microwave multiplexer modules for the 34980A Multifunction Switch/Measure Unit offer broadband switching capabilities for switching from DC to 26.5 GHz. Use these modules to route test signals between your device under test and your signal generator, oscilloscope, spectrum analyzer, or other instrumentation. A switch/attenuator driver module also allows control of switches and attenuators external to the 34980A Mainframe.
-
Product
FieldFox Handheld Microwave Vector Network Analyzer
N9925A
-
9 GHz max frequency Carry the world's most integrated handheld T/R VNA analyzer Expand your measurement flexibility with optional 2-port VNA, time-domain, vector voltmeter, cable and antenna analyzer and more Save time by simultaneously measuring all four S-parameters with a single connection Perform accurate testing with QuickCal, full 2-port unknown thru Cal, TRL Easily measure average and pulse power with a USB power sensor
-
Product
Near Field Probes 30 MHz up to 3 GHz
RF1 set
-
The RF1 near field probe set consists of 4 passive near field probes for making measurements in the development phase of E-field and magnetic field in the ranges of 30 MHz to 3 GHz on electronic assemblies. The probe heads of the RF1 set allow for measurements close to the electronic assemblies, e.g. on single IC pins, conducting paths, components and their connectors in order to localize interference sources. Field orientation and field distribution on an electronic assembly can be detected through a trained special use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They do not have an internal terminating resistance.
-
Product
Boundary-Scan Test Coverage Analysis Tool
ScanExpress DFT Analyzer
-
Test coverage statistics provide engineers and managers valuable information to make critical decisions in product development and manufacturing.ScanExpress DFT Analyzer is an automatic test coverage analysis tool for printed circuit boards and systems that include a mix of boundary-scan and non-boundary-scan devices. The tool assists design and test engineers to increase fault coverage and reduce boundary-scan test procedure development times. Using ScanExpress DFT Analyzer results in better informed test decisions.
-
Product
Defibrillator Analyzer (with pacing)
DA 2006P
-
The DA-2006 is a microprocessor-based analyzerthat is used in the testing of defibrillators. It measuresthe energy output and provided information about thepulse.
-
Product
Liquid Analyzers
-
Teledyne Analytical Instruments
Liquid Analyzers by Teledyne Analytical Instruments
-
Product
Circuit Breaker Operational Analyzer
CBScan
-
CBScan is a compact and portable circuit breaker analyzer. It has limited number of channels as compared to AutoScan, but is ideal for basic shop-floor and on-site testing requirements. This analyzer has complete functionality of AutoScan. However, to ensure portability, an external laptop is required to run the test software.
-
Product
NI-5782, 100 MHz Bandwidth Transceiver Adapter Module for FlexRIO
782705-01
-
The NI‑5782 is ideal for applications that require the acquisition and generation of IF or baseband signals with in-line, real-time processing. You can analyze acquired signals in the PXI FPGA Module for FlexRIO to perform measurements and generate response signals. Application areas include RF modulation and demodulation, channel emulation, bit error rate testing (BERT), signal intelligence, radio frequency identification (RFID) and near-field communication (NFC) test, real-time spectrum analysis, and software defined radio (SDR).
-
Product
PLS Software Suite
-
Real-time point cloud via 4G or built-in long range wifi – now with patent pending real-time RGB colorizationVehicle agnostic (designed for multi-rotors, car, bicycle, backpack, and more)Analyze LiDAR penetration and measure positions, paths and cross sections – while scanningSDK available for real-time point cloud analytics
-
Product
Transformer Winding Resistance Meters
TWA Standard Series
-
The TWA standard series instruments are designed to measure the resistance of six coils and simultaneously analyze the three-phase tap changer on load of the primary and secondary transformer coils (provided by model TWA40). This is done in a single cable configuration, with test currents up to 40A. Each transformer configuration has a special measurement algorithm that is optimized for rapid stabilization of test results. The TWA instruments generate a true DC current without ripple. Both current injection and magnetic circuit energy discharge are automatically regulated.
-
Product
HandyScope HS4 DIFF: 10 MS/s 100MHz BW, 4 Channel, USB Differential Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
HS4-10-DIFF
-
The Handyscope HS4 is the successor of the popular Handyscope HS3. Built for customers that want to extend their measuring capabilities even further, this powerful computer controlled measuring instrument now features four input channels. The HS4 has just like it's predecessor the four main measuring instruments: a Multimeter, an Oscilloscope, a Spectrum analyzer and a Transient recorder.
-
Product
VNAs for Automated Test Equipment (ATE)
-
With our USB VNAs your automated test equipment works as one software system running on a single computer. We can customize the analyzer module to fit in your system, provide extra frequency range coverage as compared to our standard VNA models should you need it in your specific application or characterize the expected performance outside the frequency limits of our standard VNAs.
-
Product
Trace Hydrogen Analyzer
GNL-400
-
Shanghai ChangAi Electronic Science & Technology Co.,Ltd
GNL-400 trace hydrogen analyzer adopts imported high-performance electrochemical sensor with latest micro computer technology. It has such functions of LCD display, upper & lower alarm, signal output and relay contactor alarm output. And can be used to measure the hydrogen concentration in nitrogen, oxygen and argon.
-
Product
Analyze HBM and CDM Waveforms
WaveAppraise
-
WaveAppraise is a modern, efficient tool for analyzing HBM and CDM tester waveforms from virtually any source. It can be used independently to verify tester waveforms and is included with GTS PurePulse and Scorpion systems. Download the free version or contact us for information on the premium version.
-
Product
Imaging Colorimeter
FW-Series
-
RayClouds Photoelectric Technology Co.,Ltd.
FW-Series Imaging Colorimeter is equipped with scientific grade CCD sensor and multi-filter, cooperated with ProICM professional analysis software to detect and analyze the optical characteristics of two-dimensional imaging screen. Improving measurement efficiency to ensure manufacturers maximize the production of high visual quality products.
-
Product
Realtime Analyzer Light
RAL
-
Quality sound measurement software equivalent to $10,000 hardware. Simple and easy-to-use RTA, Real Time Analyzer. For wide scope of audio and acoustics: car audio, home audio, concert hall and room acoustics, sound analysis and noise measurement.
-
Product
Outdoor Exposure Tester
OET
-
A comprehensive analysis of PV modules includes many different parameters. Determining the normal module operating temperature (NMOT), incidence angle effects and comparing soiling effects on different modules up to the initial degradation of PV modules are all parameters that can be analyzed with our outdoor exposure tester. The tester comes with up to twelve electronic loads installed in a 19" rack. The loads have two main functions: maximum power point tracking (MPPT) and IV curve tracing. For the advanced analysis, it is possible to change between these two modes within one test. In the normal operation mode, the electronic load keeps the module under MPP and each predefined interval an IV curve is traced. The entire tester comes with all necessary sensors such as temperature sensor, which can be attached to the module to determine the NMOT temperature like defined in IEC 61215 (MQT 05) and IEC 61853-2. The irradiation sensor is also included. In combination with our tracking system P2, it is also possible to determine incident angle effects of the PV module. It is also possible to connect other irradiation sensors for diffuse and direct irradiation, which helps to understand the behavior of the module in different irradiation conditions. An optional albedo meter is a powerful tool for the analysis of bifacial modules. The entire graphical user interface is web based and offers the possibility to access the system from the all computers in the network.
-
Product
JETCAL®1 Engine Analyzer
BH112JD Series
-
The BH112JD JETCAL® Engine Analyzer providesa superior combination of capabilities in aruggedized, portable test set.
-
Product
Impedance Analyzer, 20 Hz to 10/20/30/50/120 MHz
E4990A
-
The E4990A Impedance Analyzer has a frequency range of 20 Hz to 120 MHz. The E4990A provides an industry best 0.045% (typical) basic accuracy over a wide impedance range, with a 40 V built-in DC bias source. The equivalent circuit analysis function supports seven different multi-parameter models and helps you to simulate your own equivalent parameter values of components.
-
Product
Multi-Laser Nanoparticle Tracking Analysis (NTA)
ViewSizer 3000
-
Exosomes, viruses, and nanoparticles all have wide size distributions which defeat traditional Nanoparticle Tracking Analysis (NTA) analyzers. The ViewSizer 3000 features simultaneous measurement with three lasers to collect the most accurate distribution and concentration information over a wide range of sizes within the same sample. Where the signal from a particle is too bright and saturates the detector from one laser, the software automatically uses data from a lower power laser to ensure the most accurate size and concentration information. On the other hand, when scattering from one laser is too weak for detection, the software uses data from a higher power laser to accurately track the particle.
-
Product
Infrared Analyzers
-
Teledyne Analytical Instruments
Infrared Analyzers by Teledyne Analytical Instruments
-
Product
PXIe-5665, Up to 14 GHz PXI Vector Signal Analyzer
781774-02
-
Up to 14 GHz PXI Vector Signal Analyzer - The PXIe‑5665 is a modular, three‑stage superheterodyne analyzer that you can use as either a spectrum analyzer or vector signal analyzer. It supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. In addition, you can use the PXIe‑5665 with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5665 can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5665 provides a low-cost solution to high-performance RF measurements.
-
Product
DC BIAS CURRENT UNIT
3265B SERIES
-
To evaluate components at currents up to 125 A the 3265B DC Bias Units are used with either the Wayne Kerr 3255B series of Inductance Analyzers or the 3260B Precision Magnetics Analyzer. When one 3265B/25A or 3265BQ/25A DC Bias Unit is connected to an instrument up to 25 A of DC bias current can be set in steps of 25 mA with one unit. Additional DC Bias Units can be added such that with five units connected in parallel it is possible to set DC bias currents up to a maximum of 125 A DC.
-
Product
Hydrogen Analyzer
H‑500
-
Determination of hydrogen using the heat extraction method is a special requirement for the characterization of steel, steel alloys, copper and other metals. ELTRA’s H-500 is designed for the rapid and accurate determination of hydrogen in these materials. The H-500 analyzer uses the heat extraction technique and is equipped with a resistance furnace with quartz tube. The temperature can be set up to 1000 °C in steps of 1 °C. The usual working range of the H-500 is about 900° to 1000° C.
-
Product
Shaker Controllers
ZET 017-U Series
-
Shaker Controllers of ZET 017-U series are represented by a software and hardware complex solutions based on FFT spectrum analyzer ZET 017 with task-specific software ZETLAB VIBRO for the control of shock and vibration impact produced by electrodynamic shaker systems. The modular principle of the system structure allows to increase the number of measuring channels from 4 up to 24.
-
Product
Measuring & Analysis Equipment
-
Quality management for semiconductor manufacturing processes and liquid crystal panel manufacturing processes, which require nano-order precision. Oxygen analyzers used in firing furnaces and N2 reflow ovens.Water quality meters used to monitor the water quality of plant discharge and the pure water used in semiconductor manufacturing processes.Our measuring and analysis equipment is used in a wide range of fields.
-
Product
Zero Bias Schottky Detectors
-
KRYTAR Zero Bias Schottky Detectors are specifically designed for use in today's high-performance microwave instrumentation and systems. KRYTAR detectors are designed for such applications as power measurements, analyzing radar performance, leveling pulsed signal sources, AM noise measurements, system monitoring and pulsed RF measurements in ultra-broadband and mm-Wave applications.
-
Product
Residential/Commercial Combustion Analyzer w/ Pressure
C163
-
UEi Test & Measurement Instruments
Backed by UEi Service+ to give up to 6 years’ warranty, next day recertification, and a reduced cost of ownership. The C163 Residential/Commercial Combustion Analyzer is easy to use with a rugged design, multiple sensor protections, altitude compensation and differential pressure. Prints to optional printer and wireless App. Essential information for installing and maintaining furnaces and boilers all in one device.
-
Product
Signal And Spectrum Analyzer
R&S®FSV3000
-
Measurements at the push of a button, capturing rare events with event based actions and simple script programming with the SCPI recorder – setting up complex measurements in no time is the strength of the R&S®FSV3000 signal and spectrum analyzer. Its other major advantage is its fast measurement speed, allowing high throughput in production applications.
-
Product
HandyScope HS6-DIFF: 500 MS/s, 250MHz BW, 4 Channel (256MS/ch), USB Differential Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
HS6-DIFF-500XM-W5
-
The only oscilloscope in the world that has:- SafeGround, differential input channels that can be switched to single ended.- CMI interface.- USB 3.0 interface, 5Gb/s data transfer- Lowest noise
