Solid State Relays
-
Product
2X16 USB Solid State Switch Matrix, 300 KHz To 9 GHz
P9164B
Switch Module
P9164B 2X16 USB solid state switch matrix, 300 KHz to 9 GHz is a full cross-bar switch matrix that provides a switch based multiport VNA solution in the form of compact USB controlled involving larger scale of multi-DUT or multiport measurements such as 5G massive MIMO antenna measurement and others.
-
Product
Protective Relay Test Kit
PW460
-
PW460 Protective Relay Test Kit is the comprehensive protection relay testing equipment for all types of protective relays with high accuracy. This relay test kit has in-built output monitoring and recording function and supports testing IEC 61850 digital relay.
-
Product
PCI Reed Relay Card, 64xSPDT
50-110B-121
Reed Relay
The 50-110B-121 is a 64xSPDT PCI general purpose switching card and is part of our 50-110B/50-115B range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
Product
PXI Single Bus 74-Ch 2A Fault Insertion Switch, N/O Through Relays
40-190B-301
Fault Insertion Unit
The Single Bus, 74 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally open through relays, so in the default state, there are no paths between inputs and outputs for any signal channel. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
PXI 8 Slot BRIC Solid State 160x8 1-Pole (5 sub-cards)
40-563A-121-160X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance PXI matrix requirements and are constructed using solid-state switches. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
Protection Relay Tester
PW336i
-
PW336i protective relay tester is the best economic model with 6 current channels and 4 voltage channels, capable of automatic testing differential relay easily without changing cable connection.
-
Product
Trip Indicator Relays
TIR
-
The TIR relays are designed for event recording circuit applications, where high speed event monitoring is required. The TIR relay contacts are used to record breaker functions, relay, communication and control system operations. The TIR contacts are also used to activate alarm and/or annunciator contacts.
-
Product
High Sensitivity Reed Relays
Series 87
-
General purpose relays - sensitive versions of series 85 and 89
-
Product
Instantaneous Plug-in Auxiliary Power Relays
-
Instantaneous power relays from Mors Smitt are designed for demanding applications such as power utilities, petro chemical industries and mining. The construction of the relay and choice of materials makes these power relays suitable to withstand corrosive atmospheres, low and high temperatures, vibration, in heavy duty environments.
-
Product
Single Phase Relay Tester
PTE-100-V
-
The unit is extremely compact and rugged. The design incorporates the latest in modern digital microprocessor technology to achieve unbeatable output characteristics in terms of power, accuracy, low distortion, and dynamic capability. This technology allows users to test many different specific functions required in relay testing, without the need of additional accessories.
-
Product
Network Analyzer Instrument State Utility
VNAState
-
The VNA Instrument State Utility works with the most popular Vector Network Analyzers from Agilent / HP. It retrieves the instrument state information (frequencies, calibration, markers, etc) and stores it on disk in the PC as an "IST" file (meaning Instrument STate). The data can then be downloaded into the instrument at a later date.
-
Product
8 Channel 1GHz High Frequency for SBDT Relay Module
DP-cPCI-4158
-
DP-cPCI-4158 is a 8 channel high frequency SPDT relay module. It provides for 1000V DC isolation between channels. This module is constructed using SPDT relays.
-
Product
Automotive Relays
-
Panasonic Industrial Devices Sales Company of America
Panasonic, a world-leading Automotive Relay supplier offers product reliability and versatility with a proven track record. Designed to switch high DC current levels of 20A to 300A, Panasonic's Automotive Relays featured a sealed construction and wide operating temperatures that allow use in harsh environments. Other Automotive Relay options include plug-in and PC board terminal arrangements with pin-in-paste compatible versions. Hermetically sealed contact enclosures are also available.
-
Product
19" Solid Fixed Storage Shelf, 24"D
SS-1924
-
Sturdy 19" shelf formed of one piece of 16 ga. CRS bolts to panel mounting rails. Supports heavy chassis or power supplies or provides storage for tools, test leads, chart paper, etc.
-
Product
192 X 1 High Density Relay Multiplexer
DP-cPCI-4383
-
DP-cPCI-4383 is a 192 Channel high density Relay Multiplexer module. DP-cPCI-4383 is implemented as a 6U cPCI module. As a 192 channel multiplexer one input can be multiplexed to any of the 192 outputs. The 192 channels are divided into 8 banks of 24 channels each. This combination allows the board to be used as one group of 192x1 or two groups of 96x1 or four groups of 48x1 multiplexer. The banks are isolated from each other using tree switches.
-
Product
PXI Power Relay Module, 12xSPDT, 16 A, With Interlock
40-161A-101-HI
Relay
The 40/42-161A-101-HI is a PXI/PXIe 12xSPDT power relay module with optional hardware interlock. It is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock.
-
Product
PXI Single Bus 64-Ch 2A Fault Insertion Switch, N/O Through Relays
40-190B-401
Fault Insertion Unit
The Single Bus, 64 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally open through relays, so in the default state, there are no paths between inputs and outputs for any signal channel. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
Switch Modules - 16 Single Pole Relays Arranged as an 8x2 Matrix
JX16/AB-1
Switch Module
This module has 16 single pole relays arranged as an 8x2 matrix as shown in the figure to the left. The matrix may be operated and wired individually for up to 16 8x2's per chassis, or jumpered to the backplane to form up to a 128x2 matrix. It is available with Type S or M reed relays for high speed, long life application. These modules are usually used for 2 wire testing where high and low meter leads must be switched between any two points. Often used for 2 wire LCR meter measurements, cable testing, or open / short testing in a variety of applications.
-
Product
NI-9482, 4-Channel, SPST Relay, 60 VDC (1 A)/250 VAC (1.5 A) C Series Relay Output Module
783906-01
Relay Output Module
4-Channel, SPST Relay, 60 VDC (1 A)/250 VAC (1.5 A) C Series Relay Output Module - The NI‑9482 directly connects to a wide array of industrial devices such as motors, actuators, and DC devices. Each channel provides access to an electromechanical relay for switching signals up to 60 VDC (1 A) or 250 Vrms (1.5 A), features channel‑to‑channel isolation, and has a LED that indicates the status. The shock and vibration rating for the NI‑9482 is limited compared with other CompactDAQ and CompactRIO modules because of the mechanical relays on the module.
-
Product
Automatic Solid Phase Extraction Instrument
DRK-SPE216
-
Shandong Drick Instruments Co., Ltd.
The DRK-SPE216 automatic solid phase extraction instrument adopts a modular suspension design. It relies on a precise and flexible robotic arm, a multifunctional injection needle, and a highly integrated pipeline system, which greatly improves the efficiency of sample pretreatment and brings you easy and convenient Work experience.
-
Product
AC Filament Switching and Line Relays
-
*Heavy duty Elkonite contact tips*AC and DC versions available*AC versions available with or without internal rectifier PCB*Automated vision system and operator inspection*Comprehensive automated end of line testing*Test Certificates supplied with each relay*Certificate of Conformity supplied with each order*Recertification and repair services available
-
Product
PXI 8 Slot BRIC Solid State 256x8 1-Pole (8 sub-cards)
40-563A-121-256X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance PXI matrix requirements and are constructed using solid-state switches. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
-
Product
PXI 8 Slot BRIC Matrix, Solid State, 256x8, 1-Pole (8 sub-cards)
40-563B-121-256X8
Matrix Switch Module
The 40-563B-121-256x8 is an ultra high density 8-slot matrix module with 1-pole switching and is part of our range PXI BRIC matrices. They are available in 2, 4 or 8-slot sizes to suit high performance PXI switching requirements and are constructed using solid state switches.
-
Product
Single-in-Line Reed Relays
Series 113
-
SIL relays - Requires a small area of only 0.15 x 0.5 inches (3.8mm x 12.5mm). 10 Watts Form A or 3 Watts Form C switches. Smallest Form C reed relay
-
Product
PCI Reed Relay Card, 64xSPST
50-115B-121
Reed Relay
The 50-115B-121 is a 64xSPST PCI general purpose switching card and is part of our 50-110B/50-115B range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
Product
PXI/PXIe Fault Insertion Switch, 32-Chan 2A, N/C Through Relays, Fault Buses on M & U
40-190C-212
Fault Insertion Unit
The 40-190C-212 (PXI) and 42-190C-212 (PXIe) are fault insertion switches with 32 channels. They are part of a range of modules available with 74, 64 or 32 channels and are primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
Multi Function Relay PXI Card
GX6377
Relay
The GX6377 3U PXI multi function switch card provides users with the ability to switch both high current and general-purpose signals using only one 3U PXI switch module. The card features multiple channels of high current switching capability for 10 A and 2 A applications as well as two, 16 x 2 switch matrix groups, which can also be configured as a 32 x 2 or 16 x 4 matrix.
-
Product
Safety Relay, 4 Contacts, 10A
D-BW
-
The D-relays series are designed for demanding industrial applications such as power utilities and petrochemical industries. The construction of the relay and choice of materials makes the D-relay suitable to withstand corrosive atmosphere, low and high temperatures and vibrating environments. No external retaining clip needed as integrated ‘snap-lock’ will hold relay into socket under all circumstances and mounting directions All relays are equipped with a LED and suppression diode.
-
Product
PCI-6521, 16-Channel, ±30 VDC, 8 Sink/Source Inputs, 8 Relay Outputs (150 V), Isolated Digital I/O Device
779312-01
Digital I/O
The PCI-6521 is an industrial digital I/O module with high channel isolation and industry-standard 24 V logic levels. If a computer or application fault occurs, the PCI-6521 can use … digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. It also features programmable power-up states, digital filtering, and change detection for optimal control over your application.
