-
Product
PoE Tester
PE-100
-
The PoE Tester/Power Monitor is designed for testing standard PoE and measuring power of PoE systems, by performing both PSE (Power Source Equipment) detecting and PSE/PD (Powered device) inline testing. Compliant with IEEE802.3 af, 802.3at standard and 802.3bt ultra 4-pair up to 60W-100W. PSE detecting display PoE type (af or at), power source (Endspan or Midspan) and perform a load test for voltage drop with REV LED indicates a reversed power. Inline PSE/PD testing-measure and display in rotation between voltage (Volts), current(Amps) and power(Watts) via dual 4 digit 7 segment LEDs which provides voltage available, current flowing and how much power an PD actually need ensure sufficient power for PD to make the PoE is sustainable.
-
Product
Central Office Line Simulator
AI-7280
-
The AI-7280 is a highly flexible central office line simulator. It is designed primarily for the testing and verification of common terminal equipment, including standard telephones, Caller ID devices, SMS (Short Message Service) capable equipment, and any device using an analog Tip/Ring interface circuit. Supplied with the TRsSim software for Windows, it can analyze a telephone''s DTMF characteristics, pulse dialing and flash timing, generate various network tones and ringing patterns. Both Type I (on-hook) and Type II (off-hook) Caller ID is supported using either FSK or DTMF data transmission. As an optional component, the TRsSim software can perform SMS testing to either the ETSI protocol 1 or protocol 2 standards.
-
Product
Towing Dynamometer
RS-200K
-
RS-200K towing dynamometer is designed for testing Class A trucks and is the most full-featured, reliable and accurate towing dynamometer in the industry. The RS-200K is built with a heavy-duty steel frame, heavy-duty industrial axles and rides on an air ride suspension. The RS-200K is designed to maintain 200,000 Newtons of constant drawbar pull and the ability to simulate an uphill slope of 25%. The towing dyno uses absorbers with special high temperature coils powered by an industrial generator so there are nolead-acid batteries to charge and testing is unlimited at low speeds.
-
Product
USB-6255, 80 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device
779959-01
Multifunction I/O
80 AI (16-Bit, 1.25 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device - The USB‑6255 offers analog I/O, digital I/O, two 32-bit counters/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Custom Test Design
-
Materials Evaluation and Engineering
Some problems require solutions beyond the standard test methods and procedures routinely performed at MEE. Replicating the suspected cause of failure on an exemplar part can provide valuable information about the likelihood of that failure case. Likewise, intentionally causing component failures in a variety of ways can provide insight into possible failure scenarios. Wondering how (or if) a design or part can be tested? Give us a call – the engineers and technicians at MEE enjoy the hands-on experience of designing customized testing plans for your unique challenges.
-
Product
Server Power And Back Up Unit Test Solutions
-
Built on the proven Chroma 8000 ATS platform, these customizable solutions are specifically designed for automated testing of server PSUs, power shelves, rack power systems, bidirectional DC/DC converters for BBUs, and low-voltage high-current DC/DC converters for motherboards.
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 16.3k Ohm - SPST
50-294-131
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Programmable DC Electronic Load
DL3000 Series
-
The DL3000 series is a cost-effective, economical programmable DC electronic load with a friendly human-machine interface and excellent performance specifications. It provides a variety of remote communication interfaces to meet diverse testing needs for design and testing. A wide range of solutions are available for a wide range of industries including automotive electronics, aerospace and fuel cells.
-
Product
Test Pattern Generator Software
ScanExpress TPG
-
To deliver a product meeting the highest standards of quality and reliability, design engineers and test engineers alike must maintain test capabilities throughout the entire product life cycle, from prototype to manufacturing. Automation in test generation is essential to ensure that tests keep up with the rapid development of modern products.The ScanExpress TPG™ Intelligent Test Pattern Generator Software provides a highly advanced, automated boundary-scan test design environment—perfect for quick and efficient creation of complete boundary-scan tests for all IEEE-1149.1 and IEEE-1149.6 compliant circuit boards.
-
Product
Towing Dynamometer
RSL-25K
-
RSL-25K Towing Dynamometer is designed for testing today’s full-sized cars, SUVs and light trucks. The RSL25K is built with a steel frame, sheet metal body and rides on an independent, coil spring suspension. The RSL-25K uses eddy current absorbers for power absorption. The power is provided by batteries and an alternator.
-
Product
PXI 16 Trib Daisy Chain Switch 75 Ohm 96 Way
40-793-701
Relay
The 40-792/793 Daisy Chain Switching Module is designed for telecom test applications. It allows production or verification testing of SONET/SDH transmission multiplexers switching 2MBit/s or 1.5MBit/s data. Traffic is sequentially Daisy- Chained through all tributaries (or any selection of tributaries), modules can be cascaded to test any number of tributaries.
-
Product
64-Channel Boundary Scan Digital I/O Scan Module
JT 2111/MPV DIOS DIN
Digital I/O Module
The JT 2111/MPV is a 64 channel boundary-scan digital I/O scan module enclosed in an impact resistant housing. The module is designed to test and control edge connectors, on-board connectors and logic clusters in boundary-scan applications. Multiple modules can be connected serially to increase the number of I/Os. Available with 96-pin DIN 41612 connectors and 20-pin 0.1″ pitch IDC connectors.This JT2111/MPV DIOS module is also available through our webshop.
-
Product
PCI High Density Resistor Card 18-Channel, 8 Bit, 0 To 255 Ohm
50-295A-121-18/8
Programmable Resistor Module
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Cable Test Van
ETL-10M
-
ETL-10M is a cable test van with three-phase connection designed for testing cable insulation with DC (rectified) voltage up to 60 kV and testing other electrical objects with up to 50 kV AC voltage of industrial frequency.
-
Product
Test Management Software
ActivATE™
test
Easily create and run robust test programs in semiconductor automated test systems with ActivATE™ test management software. Designed by test engineers for test engineers, ActivATE™ tames automated test complexities with elegant simplicity.
-
Product
AC / DC Electronic Loads – Benchtop Testing to Automated Test Systems
-
Chroma Systems Solutions, Inc.
Chroma is the global leader in Electronic Load manufacturing. Chroma’s AC Electronic Loads are designed for testing uninterruptible power supplies(UPS), Off-Grid Inverters, AC sources, and other power devices such as switches, circuit breakers, fuses and connectors. Chroma’s DC Electronic Loads are used for power testing in all markets including automatic test systems, LED, power supply testing, battery testing, and fuel cell testing. Chroma loads can do it all including full current down to 0.4VDC, CZ mode, user defined waveforms, timing measurements, and 3 current ranges per load. Chroma’s electronic loads come standard with either USB or RS232 ports for control and can be configured for GPIB (IEEE-488) control as well.
-
Product
Two-Way Radio Communications and High Speed Data Transfer
Leaky Feeder System
-
Leaky Feeder systems offer clear two-way radio communication and high-speed data transfer capabilities throughout your underground complex.PBE’s Leaky Feeder System can be tailored to specific site requirements to provide the best radio coverage and data communications. This two-way radio system can provide complete communications coverage for your site, including above ground surface coverage. PBE offers design, supply, testing and commissioning of temporary and permanent communication infrastructures for underground mines, tunnels, plants and buildings. PBE provides a wide range of leaky feeder system options: conventional leaky feeder system, CMTS system, permanent radiating cable network and hybrid networks.
-
Product
Circular Blade Crosscut Tester
MCT-5
-
Is designed to test the adhesion and brittleness of dry coats of paint on their substrate by means of a set of six circular blades and two guide blades.
-
Product
6 Sided Bed of Nails Testers
BoxProber Family
-
6 sided Bed of Nails circuit board test fixture. Probes top bottom and all 4 sides. Central camming mechanism pull plates inward. Mechanically or electrically actuated options. Designed primarily for testing products in plastics. Side access electrically probes outside panel connectors. The unit will also optically read LEDs and key segments off LCD displays. Solenoids will press buttons and servos will turn selector switches. DC motors are used to adjust multiple turn potentiometers. Microphone will detect audio output tones. Top and bottom of circuit boards can also be probed if removable access panels are available. This unit will also probe all 6 sides of a circuit board. This is typically utilized in applications where connector testing is required.
-
Product
OTDR
AV6416
-
Hangzhou Softel Optic Co., Ltd.
AV6416 palm OTDR is the newest instrument designed for testing FTTx network. It's mainly used to measure the physical characteristics of optical fiber under test, such as the length、the transmission loss and the splice loss etc.. It can also locate the faults or breaks of optical fiber. It's widely applied in the manufacture, construction and maintenance in optical fiber communication system.
-
Product
Liquid Dielectric Test Cell
LT-4123
-
The LT-4123 Liquid Dielectric Test Cell is designed for testing the quality of materials such as the insulating oils used in transformers and the resins used in the manufacture of thermosets. With the LT-4123 Liquid Dielectric Test Cell, users can measure the AC loss characteristics and permittivity of liquids. The data gleaned from these measurements are used to set quality benchmarks for fluids during testing and manufacturing.
-
Product
Dynamic Mechanic Loading Tester
-
King Design Industrial Co., Ltd.
*Complies with IEC 61646, IEC 61215 mechanical load test specification. * Air pressure is adjustable, output range is from 2400pa to 5400pa ±5% . * Maximum measurement range: 220 x 260 cm. * Apparatus structure material：aluminum-extruded. * Fixtures and holders can be customized design for requirement of testing module. * Manual operation is simple; manual maintenance is easy.
-
Product
Three Phase Round Energy Meter Test Bench Type KP-S3000-C
-
Bofa Instrument & Equipment Co., Ltd
Three phase Round energy meter test bench Type KP-S3000-C is designed for testing three-phase round energy meters (ANSI Socket type), it is mainly exported to countries in Noth America and South America. It is an ideal testing eqiupint for energy meter factory or R&D institute. All the testing procedures can be automatically operated by PC or by Keyboard manually.
-
Product
Leather Testing Machine
-
Dongguan Kejian Instrument Co., Ltd.
Test method uses clean ball placed within the material applications, steel ball itself of the impedance and total weight, must be in conformity with the provisions, on this condition detection material zigzag waterproof penetration index, using the latest inductive components and special design, test as long as materials applications in water infiltration immediately automatic stop counting or in setting time (test times) arrived, namely automatic stop and display the time or times.
-
Product
VDV & USB Cable Tester
PK-2016/2016R
-
The VDV & USB cable tester is designed for testing today’s media computer networks which combination of telephone USOC (voice), twisted pair (data) and coax security / alarm (video) as well as PC-USB 2.0 3.0 cables.
-
Product
Towing Dynamometer
RS-8K
-
Taylor Dynamometer’s RS-8K Towing Dynamometer is designed for testing today’s mid-sized cars and SUVs. The RS-8K is built with an all aluminum frame, an aerodynamic body and rides on an independent, air ride suspension and uses an eddy current absorber with special high temperature coils to absorb energy. The RS-8K is powered by an industrial generator, so unlike battery/alternator Towing Dynamometers, there are no lead-acid batteries to charge and testing time is unlimited at low speeds.
-
Product
Digital Igniter Tester
Alpha 4314
-
The Alpha 4314 Digital Igniter Tester is a portable digital ohmmeter which has been specifically designed for ultra-safe resistance testing on explosive devices (i.e. squibs, detonators).
-
Product
Board Test Fixture Probes
-
Offering a wide range of standard spring contact probes to meet your testing requirements and has long been recognized as the world’s largest probe manufacturer. With over 60 different probe series ranging from 0.02" (0.51 mm) to 0.187" (4.75 mm) pitch with multiple length, travel, ICT, lead free and rotator options, we provide a full portfolio designed for general purpose test on bare boards, loaded printed circuit boards and surface mount assemblies.
-
Product
Panelized Walk-In Chambers
-
ESPEC North America builds dozens of walk-in test chambers every year for top companies testing automotive, electronics, communications, aerospace, and other products. Drive-in test chambers for automobiles are one of our top specialties. Stability walk-in rooms are another specialty, designed for light-duty testing or long-term steady-state evaluation of pharmaceuticals and other products.
-
Product
Test And Measurement
-
Test and Measurement supplies test, measurement, and analysis equipment and software for product design optimisation, manufacturing control, and environmental monitoring systems. Markets are principally the aerospace, automotive, consumer electronics and oil and gas industries. For customers in the automotive and aerospace industries, our products and applications help them to design and test new products whilst reducing time to market. In consumer electronics, our equipment and software enable customers to refine the performance and accuracy of their products and to test them in the production process. In the environmental monitoring market, the desire for higher standards of community comfort is creating additional demand. In the oil and gas industries, our products and solutions optimise the recovery rates of oil and gas reservoirs and support the development of cost-efficient extraction processes in a safe manner that minimises the impact on the local environment. The operating companies in this segment are Brüel & Kjær Sound & Vibration, ESG Solutions, HBM and Millbrook.
