Rapid IO
"the unified fabric for Performance Critical Computing"; rapidio.org
-
Product
PCI Express Digital I/O Boards
PEX-P8POR8i
-
PCI Express x1, 8-channel isolated digital input.8-channel PhotoMos Relay output. Includes one CA-4002 D-Sub connector.
-
Product
Digital I/O Modules
-
ADAM-5000 DI/O modules are equipped with high density channels, isolation, short circuit protection, failure protection and hot swap functionality.
-
Product
PXI-6254, 32 AI (16-Bit, 1 MS/s), 48 DIO, PXI Multifunction I/O Module
779118-01
Multifunction I/O
The PXI-6254 offers analog input, correlated digital I/O, two 32-bit counters/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PCI Express Analog and Digital I/O
826
-
Six advanced 32-bit countersDirectly supports incremental encoders, pwm/pulse generation, frequency/pulse/period measurement16 analog inputs, 16-bit, 300 ks/s8 analog outputs, 16-bit, 900 ks/s48 digital I/Os with edge captureWatchdog timer, 3 stages
-
Product
32-CH Separate I/O Terminal Base
HSL-TB32-MD
-
The HSL-TB32-MD discrete I/O terminal bases provide reliable and convenient wiring for HSL-M series products. The separate connection can make it easy to wiring, and the separate fuse can protect each I/O point. This low cost terminal base is particularly useful for users who need convenient way to construct their own signal ?Vcondition arrangement.
-
Product
8DI/8DO RS-485 Remote I/O
ADAM-4050
-
8ch digital input/8ch digital outputProtocols: Modbus RTU,ASCIIWatchdog timer to recover the system
-
Product
PCI-6511, 64-Channel, ±30 VDC, Sink/Source Inputs, Bank-Isolated Digital I/O Device
778966-01
Digital I/O
The PCI-6511 is an industrial digital input interface, with eight banks of isolated channels. If a computer or application fault occurs, the PCI-6511 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
Safety Certified I/O Modules
HY-TTC 30XSH
-
HY-TTC 30XSH, a member of the HY-TTC 30X family, is certified by TÜV Nord according to the EN 13849 standard and fulfills Performance Level c (PL c) requirements. Just as the other family members this certified unit must be used in combination with a master module. For safe communication the standardized CANopen Safety protocol is applicable since compliance to the European standard EN 50325-5 for CANopen Safety is provided.
-
Product
Analog I/O and Digital Receivers
-
Curtiss-Wright Defense Solutions
Many mission-critical applications require small form factor solutions, but cannot compromise ruggedization requirements or I/O and processing performance. Our VPX, XMC, PMC and FMC module-based sensor I/O solutions are designed to handle the toughest operating environments while packing maximum functionality in a minimal physical footprint.
-
Product
8AI/5DI/4DO Intelligent I/O Gateway
ADAM-6717
-
Linux Open Platform8ch analog input (current or voltage)/5ch digital input/4ch digital outputProgram by linux C API, Node-RED (graphic programming environment)Cloud/Database access, edge data analysis and logic control, data visualization by dashboardInterfaces: x2 RS-485, x2 Ethernet port, x1 USB Type-A 2.0, x1 USB Micro-B 2.0
-
Product
High Speed Digital I/O
-
ADLINK's high-speed digital I/O cards features 32 or 64 high-speed single-ended I/O channels and up to 50 MHz data transfer rate with 200 MB/s data throughput—ideal for large-scale digital data exchange.
-
Product
8AI RS-485 Remote I/O
ADAM-4017
-
8ch analog input(voltage or current)Protocols:ASCIIWatchdog timer to recover the system
-
Product
Communication and Differential IO Board
MS 1707
-
- Four RS232 PORTS with full handshake- 16 Differential Input Channels- 16 Differential Output Channels- Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
Mobile Apps for iOS and Android
LoggerLink
-
LoggerLink Mobile Apps are simple yet powerful tools that allow an iOS or Android device to communicate with our CR200X, CR800, CR850, CR1000, CR3000, or CR6 dataloggers via an IP device (NL115, NL116, NL120, NL121, NL201, NL240, RavenXTV, RavenXTG, LS300G). LoggerLink for Android also supports Bluetooth communication for these same dataloggers using an RS-232-Bluetooth adapter. The apps support field maintenance tasks such as viewing and collecting data, setting the clock, and downloading programs.
-
Product
4DI/4Relay Modbus Ethernet I/O
WISE-4060LAN
-
Supported protocols: Modbus/TCP, TCP/IP, UDP, DHCP, HTTP, MQTTSupports RESTful web API in JSON formatSupports local logging with RTC time stampSupports mobile device web configuration in HTML5Supports 10~30 VDC power with reverse protection
-
Product
I/O Rack
-
ADAM-5000/485 and ADAM-5000E are Modular I/O System, as well as 4-slot / 8-slot Distributed DA&C centralized i/o systems which conform to the EIA RS-485 communication standard. RS-485 was specifically developed for industrial applications to transmit and receive data at high rates over long distances. The ADAM-5000L/TCP and ADAM-5000/TPC are both Ethernet-based I/O systems. Without a repeater, they can cover a communication distance up to 100M.
-
Product
JTAG Boundary-Scan I/O Modules
SCANIO Family
-
The Corelis family of SCANIO™ modules turn any IEEE standard 1149.1 boundary-scan controller into a powerful digital boundary-scan tester. The SCANIO family of products use boundary-scan gate arrays to add control and visibility to connectors, traces, and logic that can not be tested using traditional boundary-scan techniques.The SCANIO products, when combined with a boundary-scan controller, operate as a traditional “bed-of-nails” tester except access to the stimulus and response I/O’s is achieved via boundary-scan.
-
-
Product
PCI-6528, 48-Channel, 24 Sink/Source Inputs, 24 Sink/Source Outputs, Channel-Channel Isolated, Digital I/O Device
778833-01
Digital I/O
The PCI-6528 is an industrial, parallel digital I/O interface.With programmable power-up states, you can configure the initial output states in software, to ensure safe … operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6528 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
Isolated Digital I/O 60VDC, 150mA
OTP2 module no.186
Test Platform
The National Instruments PXI-6528, PCI-6528, and PXI-6529 Digital I/O Modules are isolated digital I/O interfaces for PCI and PXI. These modules can use inputs from NI 6528 and PXI 6529 devices to capture the status of sensors, actuators, and logic devices. NI 6528 devices have 24 SSR outputs for switching external devices with input currents up to 150 mA. The NI 6528 and PXI-6529 devices are suitable for a variety of applications, from automotive development and industrial factory automation to aerospace, laboratory research, and biomedical applications due to their high current handling capacity and isolation.
-
Product
I/O Wiring Cable
PCL Series
-
I/O wiring cable sets are designed for easy field wiring capabilities. The PCL-1050 I/O wiring cable series can be used with multiple I/O cards.
-
Product
2.4G/5G Wi-Fi IoT Wireless I/O Module
WISE-4250
-
Supports IEEE 802.11 ac (2.4/5GHz) for stable wireless connectivitySupports interchangeable I/O and Sensor modules (additional purchase required) and is easily configured with web UISupports MQTT and RESTful API protocols for uploading data to cloud service platforms such as AWS, Azure, SCADA, and WebAccessSmart Roaming enables seamless AP switchingSupports WPA3 / TLS 1.3 encryption and X.509 certificate authentication for secure data transmissionWith UDP-based AES-128 encrypted wireless P2P, abnormal inputs can automatically trigger up to 16 WISE modules in the fieldStores 10,000+ data points locally with SNTP/RTC time sync and Watchdog timer auto connection recovery
-
Product
Smart I/O & Communication
-
Fulfill the customized expansion, provide faster response to market and include isolated / non-isolated communication and digital input/output modules
-
Product
I-87KW High Performance I/O Modules
-
The I-87K High Performance Modules are for use with ViewPAC, WinPAC, XPAC and LinPAC controllers.
-
Product
Rear-Panel I/O Transition Module
CP3-GESW8-TM8
-
CP3-GESW8-TM8 is a rear-panel I/O transition module providing flexible access to CP3-GESW8 or NETernity™ CP3-GESW8N rear-panel I/O. Up to eight Gigabit Ethernet ports of the switch are accessible from the transition module's stacked RJ-45 connectors. Each Ethernet port is routed as four 100 Ohm differential pairs.
-
Product
IoT Ethernet I/O Modules
WISE-4000/LAN
-
The WISE-4000/LAN series is a newly designed IoT Ethernet I/O module which supports new RESTful web API for IoT applications. A HTML5 web configure interface enables users to configure WISE modules without the limitation of a platform or operation system. The built-in data logger function logs data with time information, then be retrieved in a bundle. Wide operating temperatures enable the WISE series to be implemented in more IoT data acquisition applications.
-
Product
IOS Subsystems
-
Analog Devices has been the leader in isolated signal conditioning for more than 20 years. ADI IOS products feature complete modular solutions for industrial signal conditioning. These products are the benchmark for isolated signal conditioners, with price and performance unmatched in the industry.
-
Product
6U VME I/O & Comm Board
64C2
-
NAI’s 64C2 is a 6U VME multifunction I/O and communication board with six function module slots that can be configured with a variety of I/O and communication functions. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
Product
PCI-6221, 16 AI (16-Bit, 250 kS/s), 2 AO, 24 DIO PCI Multifunction I/O Device
779066-01
Multifunction I/O
The PCI-6221 offers analog I/O, correlated digital I/O, two 32-bit counters/timers, and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
USB-6001, 8 AI (14-Bit, 20 kS/s), 2 AO (5 kS/s/ch), 13 DIO USB Multifunction I/O Device
782604-01
Multifunction I/O
8 AI (14-Bit, 20 kS/s), 2 AO (5 kS/s/ch), 13 DIO USB Multifunction I/O Device - The USB‑6001 is a low-cost, multifunction DAQ device. It offers analog I/O, digital I/O, and a 32‑bit counter. The USB‑6001 provides basic functionality for applications such as simple data logging, portable measurements, and academic lab experiments. The device features a lightweight mechanical enclosure and is bus powered for easy portability. You can easily connect sensors and signals to the USB-6001 with screw-terminal connectivity. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
