EV Testers
See Also: EV Test Systems
-
product
MTM-Bus Tester
PXIe-1149.5
The Corelis PXIe-1149.5 is a versatile, multi-mode instrument for interfacing with MTM-Bus modules. The PXIe-1149.5 adds MTM-Bus master, slave, and monitoring with full IEEE-1149.5 electrical and protocol compatibility with a standard PXIe interface for convenient integration into any Test Program Set (TPS).
-
product
Gearbox Tester
The gearbox tester was designed to test the Azimuth Drive Unit (ADU) for a missile launcher. The ADU is the horizontal position controller for the launcher. It consists of a main drive shaft, a manual drive shaft and an output drive shaft. This system uses a multi-axis motion controller to operate.
-
product
Open/Short Tester for Reverse Engineering Applications
Panther 2K-CT
Qmax Test Technologies Pvt. Ltd.
Panther 2K-CT is a versatile open\Short tester designed especially for reverse engineering application of tracing circuits of undocumented PCBA’s.Its innovative measurement technology helps tracing PCB tracks between components in a given circuit board. It can accommodate various types of clips\grabbers and connectors to access the device pins to trace the connectivity. Its user friendly software guides the user to place and move cluster of IC clips and probes to learn the connectivity and to generate netlist.
-
product
Hoist Tester
The system has the capability of operating hyraulic powered hoists, DC powered hoists and 400Hz AC powered hoists. When a unit is connected to the system it is automatically detected and the system will load the unit's control software, acceptance procedures and operational safety limits. By doing all of this the operator does not need to worry about anything other than installing the unit and clicking Run to execute a full test procedure.
-
product
Bit Error Rate Tester - MATRIQ
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
product
KVS Rugged Igniter Tester With Current Monitor
4314
The Valhalla Scientific Model 4314 KVS Digital Igniter Tester is designed to provide extremely safe and reliable resistance testing of explosive or volatile devices. Proven uses include fuses, squibs, igniters, explosive bolts, automobile airbag initiators and many others.
-
product
120 GBd High-performance BERT
M8050A
The Keysight M8050A high-performance bit error ratio tester (BERT) enables accurate characterization of receivers used in next-generation data center networks and server interfaces. With uncompromised signal integrity, support for NRZ, PAM4, PAM6, and PAM8 signals, and data rates up to 120 GBd, the flexible architecture of the M8050A supports 1.6T pathfinding as well as other leading-edge technologies.
-
product
MXE EMI Test Receiver, 3 Hz to 44 GHz
N9038B
The Keysight N9038B is a standards-compliant MXE EMI test receiver and diagnostic signal analyzer built on an upgradeable platform. You choose the frequency coverage you need to fully test devices with outstanding accuracy and sensitivity across required ranges.
-
product
Universal A/V Tester
This tester was built for our client with the specific requirement that specific UUTs can be added to the system by our client. We handled developing test software for the first 2 UUTs utilizing an open programming structure that allowed programming modules to be strung together to create test programs for any additional UUT that our client wants to add in the future.
-
product
PAM4 Bit Error Rate Tester.
BERT-1102
The BERT-1102 is a 4 or 8-channel PPG and Error Detector for the design, characterization and manufacturing test of optical transceivers and opto-electrical components with symbol rates up to 29 GBaud/s in both NRZ and PAM4 formats. With scalability and exceptional signal fidelity, it is a cost-effective test solution for up to 400 Gb/s communication eco-systems.
-
product
Automated Coherent Receiver Tester
CoRx Tester.
Quantifi Photonics’ CoRx Tester provides automated measurement of key coherent receiver performance parameters. The CoRx Tester is comprised of a pre-configured PXI chassis, a two-channel tunable laser, a polarization controller, and a two-channel Variable Optical Attenuator (VOA) with built-in power meter. Just connect the two optical outputs to your Integrated Coherent Receiver (ICR), connect your ICR to the oscilloscope and let the CoRx Tester software do all the rest.
-
product
Error Detector Remote Head 32 and 17 Gb/s
N4952A
The N4952A is an affordable and compact error detector remote head available in 4 to 17 Gb/s and 5 to 32 Gb/s configurations. Compatible with the N4960A Serial BERT controller, it is the perfect solution to test up to 32 Gb/s per channel for 100 Gigabit Ethernet applications and other high-data rate devices. The N4952A error detector supports PRBS or user patterns and operates up to 32 Gb/s in a single band with no gaps or missing data rates. The remote head allows the test equipment to be located very close to the device under test, eliminating the need for long cables that degrade signal quality.
-
product
EV Charging Station Tester
EV : ChargeCheck
The EV Industry’s Charging Station Tester of Choice. • Simulates an electric vehicle • Tests J1772 (type 1) tethered leads • Tests IEC62196 (type 2) sockets • Tests IEC61851-1 mode 3 communication compliance • Tests for correct polarity • Tests for earthing presence • Tests contactor actions.
-
product
EV And Pack/Module Tester
Discover the Series 8500, an innovative and fully automated test system engineered to evaluate the performance of Electric Vehicle (EV) components, Energy Storage batteries, Modules, and Packs in real-world conditions. This high-specification system not only delivers accurate results but also allows the energy produced during discharge to be returned to the electrical grid.Using Maccor’s standard fully featured battery test software, the Series 8500 can perform virtually any type of battery test including FUDS, SFUDS, DST etc. for electric vehicle batteries and standard cycling tests for energy storage devices.
-
product
ABex PXI to Analog Bus Bridge with Digital IOs
ABex AM-300 Controller
The ABex system controller ABex AM-300 is required to control the analog bus of a ABex chassis. It is used as an interconnection bridge between PXI and ABex backplane.In addition it features a whole bunch of additional functionality. Despite the 96 open drain outputs it has galvanically isolated IOs, and communication interfaces.
-
product
EV Diagnostics
A high voltage battery charger and discharger. Improve battery pack capacity with constant current charge, and discharge modes.
-
product
Bit Error Rate Tester - PXI
BERT 1001/1005 Series
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
product
eVe LIDAR
eVe LIDAR aims to provide the ESA-Aeolus mission with a flexible, mobile reference ground-based LIDAR system capable of providing well-characterized fiducial reference measurements of aerosol optical properties
-
product
HEV & EV Power Tester
EVd-40
The EVd-40 Power Tester is a pre- and post-reconditioning tool for quality control of aftermarket HEV & EV battery production. The equipment integrates a “smart” charger (Sorensen XG 1700 or Kepco KLN 1500W) with NuVant Systems high power discharge electronics. The "power test" discharges battery packs at high power (10,000 watts), while tracking module voltages. The software monitors up to 40 module voltages at a time, identifying any weak modules. The "smart" charger performs charging constant current (CC), constant voltage (CV) and complex mixed mode constant current – constant voltage (CCCV) charging protocols at voltages up to 600 V. This enables recharge of any type of rechargeable battery.
-
product
EV Battery Test System
Shenzhen Sinexcel RE Equipment CO., Ltd
5V cell equipment adopts Sinexcel innovative circuit design + high-speed DSP complex algorithm, the detection process supports multi-gear switching; The equipment integrates voltage, temperature, pressure and other auxiliary channels, 20ms high-speed working condition simulation and other practical innovative functions to meet all aspects of battery electrical performance testing.
-
product
EV &Recharging Testing
PONOVO has long-term follow-up technology in China and abroad. Based on its own mature intelligent power detection equipment, and according to its own advantages in the field of new energy, PONOVO could be able to provide users with professional new energy test system solutions. In the field of electric vehicle technology, the electric vehicle charging facility detection platform based on the Internet cloud platform was introduced. This platform is one of the few domestic testing platforms that can automatically test the charging piles for network inspection, project acceptance, and factory testing. The platform has the advantages of automatic testing, low usage threshold, and high integration. It is widely used in the detection of relevant charging facilities in more than 20 provinces and cities in China, effectively meets the inspection of electric vehicle charging stations, and provides powerful technical support for the site acceptance test of charging stations.
-
-
product
64 Gbaud High-performance BERT
M8040A
The Keysight M8040A is a highly integrated BERT for physical layer characterization and compliance testing. With support for PAM-4 and NRZ signals and data rates up to 64 Gbaud (corresponds to 128 Gbit/s) it covers all flavors of 200 and 400 GbE standards.
-
product
Battery (EV) Automatic Test System
Landrex Technologies Co., Ltd.
Battery (EV) Automatic Test System
-
product
EV& Charging Pile Test Set
AC Testing
With the Industrial development globally, Electric Cars is becoming more and more popular gradually in different countries. In the future, we can say that Electric Vehicles shall replace the ordinary cars soon and there are many charging piles, recharging station built up to meet the requirements to EV charging.
-
product
PDIV Tester for EV Motor
PDIV 500-T
Shanghai Dean Electrical Co., Ltd
Differing from partial discharge with high frequency pulse which produce sound and light phenomenon, the power frequency AC voltage reaches a certain threshold, can only produce instantaneous current leakage around the tested sample, it can be detected through discharge capacity (unit: PC) to evaluate partial discharge phenomena..The instrument PDIV 500-T is designed to put samples such as enameled wire, insulation paper/film, and electric motor stator in the High temperature / humidity environment chamber, applying a power frequency voltage with a programed rising speed, and prefect ground connection must be guaranteed , through the coupling capacitor as the medium, the continuous detection of discharge capacity against the voltages will create formulation between the Voltages and discharge capacities (pc), the software will find the discharge voltage threshold called PDIV.
-
product
EV Profiler Kit V2
Harness the power of single-molecule localization microscopy to characterize EVs across scales. Quantify nanometer small, rare, and precious EV samples with super-resolution precision. ONI’s EV Profiler helps you focus on answering the right questions about your EV populations.
-
product
EV Test Equipment
Di-LOG’s New EV Test Equipment Range which includes the DL9100 series MFT incorporates the DL9120 and DL9130EV with both products boasting DC capability, paving the way for a host of tests-specific to the *EV and PV sectors, mainly the ability to conduct a Type B (Pure DC) RCD test.
-
product
Dynamometers For EV & Traction Motors
MOTOMEA’s extensive catalog puts years of innovation at your fingertips. While we invite you to browse online today, we also encourage you to contact us directly to source the specific products you need.
-
product
EV Battery Pack Test Equipments
Guangdong Bell Experiment Equipment Co.,Ltd
All industrial battery tester from BELL lithium battery test chamber supplier meet the standards of GB31467.3, ECE-R100 and UL2580. The tests mainly simulating all the condition that driving an EV meet, including battery crush test, battery drop test, flammable test, temperature cycle test, short circuit test, thermal test, explosion test, and environmental test, etc.
