Filter Results By:
Products
Applications
Manufacturers
-
product
Current Probe
DCFlex
Power Electronic Measurments Ltd
The DCflex is an easy to use, low cost, thin and clip-around DC current probe. It is suitable for measuring large DC currents of >2kA. The DCflex takes a single shot measurement of the DC current with a typical accuracy of ±1%. It is important to understand that the DCflex does not provide a continuous measurement of DC current.
-
product
DC Insulation Monitor
ISM-200
Kongter Test & Measurement Co., Limited
ISM-200 Insulation monitoring system is a high accurate and secure online monitoring equipment for DC system insulation. It is designed for the measurement of different types of ground fault, insulation decreasing, AC signal interruption, DC signal interruption and so on.
-
product
DC Vibration Unit Tester
BK2116
As the technology for BLDC motors advances, more advanced testing is also needed. The BK2116 DC Vibration Motor Tester was designed when of several of our clients needed to test the new generation of 3 port DC vibration motors. Using the BK2116, you can test the electrical specifications (RPM, current, drop pulse, and start up voltage) and also vibration level, and noise of motors with either 2 or 3 ports. The BK2116 can concurrently test 2 DUT's and BaKo's Test Shop software makes it very easy to set up and test. And because you use it with a PC or notebook, you can see graphs of the data as you test, and also save it to analyze later, or to analyze the data you gather over time.
-
product
DC Cable Testing DC cable testing
Overvoltage protection is critical to the long-term health of any cable. DC overvoltage testing (also known as withstand testing) is the most popular method of general condition and integrity assessment in the power, industrial and domestic markets. This method of testing is distinguished a number of key advantages:
-
product
1 / 2 / 3 MHz Multi-Waveform Signal Generator
MSG1M / MSG2M / MSG3M
- Wide frequency range- Sine, triangle, square, ramp, pulse, TTL (Sync) & DC outputs- Low distortion high resolution on low frequency output attenuation up to 80dB- Variable DC offset control- Four digit digital display with frequency indication in Hz, KHz, MHz/Amplitude display
-
product
Hipot Testers
Hypot® Series
The Hypot Series sets the standard for safety and efficiency in production line Hipot Testing. Whether your application requires AC Withstand tests, DC Withstand tests, or Insulation Resistance tests, The Hypot Series provides innovations that will allow you to begin achieving best practices for safety and efficiency without the need for an expensive automated test system or connection to a PC. You can even connect the Hypot Series with the HYAMP Series to form a seamless safety compliance system for Hipot and Ground Bond Testing.
-
product
DC Resistive Load Banks
LB-Series
Eagle Eye offers multiple DC Load Banks ranging from 10 480 VDC at 1 amp or 5 amp Resolution. These load banks offer a simplistic solution to UPS Battery Load Testing. Each load bank is easy-to-use with an LCD display operator control panel and user-friendly fan switches, load step switches, and master load switches. UPS load testing stimulates a real-world performance demand of a critical power
-
product
DC Power Supplies
DLM 600
AMETEK Programmable Power, Inc.
The Sorensen DLM 600 series of programmable power supplies is designed to provide continuously variable output voltage and current for a broad range of applications in a compact 1U (1.75 inches) high, half-rack (8.5 inch) wide chassis.
-
product
Autoranging System DC Power Supply, 1000 V, 30 A, 10000 W, 208 VAC
N8930A
The Keysight N8900 Series provides 5 kW, 10 kW, and 15 kW autoranging, single-output programmable DC power for ATE applications that require just the right amount of performance at just the right price. The N8900 Series power supplies' autoranging output characteristic enables unprecedented flexibility by offering a wide range of voltage and current combinations at full power. Power supplies with "rectangular," or traditional, output characteristics provide full power at only one voltage and current combination. Just one N8900 does the job of multiple power supplies. It's like having many power supplies in one!
-
product
RF Power Transistors
Silicon Bipolar
Macom Technology Solutions Holdings Inc.
At MACOM we offer a broad range of silicon bipolar transistor products designed for applications ranging from DC to 3.5 GHz. Our silicon bipolar transistors are ideal for civil avionics, communications, networks, radar, and industrial, scientific, and medical applications. Our all-gold metallization fabrication processes ensure high performance and long term reliability for ground and space applications.
-
product
Voltage logger0 to 2.5V
TK-4703
Supplied with an input cable, this logger can measure voltages up to 2.5V DC and can be connected to many industry standard devices, such as CO2 sensors and current clamps, enabling the logging of a wide range of process parameters.The unit is particularly useful when space is at a premium.
-
product
GPS, GLONASS, Galileo Splitter 8 Way, TNC, 1000 - 2000 MHz, 50 Ohm, Passive
GPS820
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo splitterLow Insertion Loss (0.4 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)15 VDC & 75 mA max on DC block portsTri Alloy TNC Female (Jack) 50 Ohm
-
product
Insulation Resistance Testers
Shanghai Beha Electronics Co., Ltd.
*This is a variable high voltage insulation tester from 500V to 15kV in 500V steps.*The is menu driven and uses Dynamic Current Auto ranging technology.*It has a Bar-Graph which displays the voltage stressing the insulation while the test is in progress and the voltage decay during the automatic discharge of the tested circuit.*The top line of the display shows the elapsed time at the start of the test. Digital readout of the total time will remain displayed even after testing has ceased.*A 4-digit display (2000 counts) is showing the actual insulation resistance.*This instrument displays a voltage warning and sounds when AC or DC is present before injecting the test voltage.
-
-
product
AC to DC Programmable Power Sources
CEHCO can supply AC to DC Programmable Power Sources. We offer standard or customized solutions. The ADG-L Series is up to 1000 VDC maximum output. ADG-P Series is up to 2000 VDC maximum output.
-
product
DC to AC Power Inverter
TE-1206B
Help to operate all kinds of devices need the AC power, such as electric lights, kitchen appliances, power tools, TVs, radios, computers and more. The extra USB can provide power for using/charging mobile phones and digital devices conveniently.
-
product
AC/DC Power Capacitors
ACF Series
For 70Vac~400Vac / 100Vdc~700Vdc Pulse Current requirement, please refer to our DC Pulse Current Capacitors for Power Electronic applications.For continuous and High RMS Current requirement, please refer to our High AC Current Capacitors LC series, which support continuous duty even at +105C.We manufacture AC Filter Capacitors for a wide variety of applications with different Capacitances, Voltages, Discharge Energy ranges, dv/dt, Pulse Discharge Currents, RMS Currents, frequency ranges, size restriction and even capacitor mountings.
-
product
PXIe-4137, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 100 fA Precision System PXI Source Measure Unit
783761-02
PXIe, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 100 fA Precision System PXI Source Measure Unit - The PXIe-4137 is a high-precision, system source measure unit (SMU). It features 4-quadrant operation and sources up to 40 W of DC power and can pulse up to 500 W. Analog-to-digital converter technology helps you perform high-precision measurements with a current resolution of 100 fA or high-speed acquisitions up to 1.8 MS/s. The module also can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. The PXIe-4137 is ideal for a broad range of applications including manufacturing test, board-level test, and lab characterization with devices such as ICs, power management ICs (PMICs), and RFICs and discrete devices including LEDs and optical transceivers
-
product
H.V. Multifuntion Phasing Sticks
PC7k, PC11k, PC22k, PC33k, PC44k
Standard Electric Works Co., Ltd
● No user’s assembled parts.● Dual color-coded scale (%, Vac).● Neon indicator when >1200Vac.● Lightweight, robust & compact.● Carry case included.● Compare between phases.● Measure and test phase to earth.● High quality fiberglass wound rod.● Self powered operation. No battery required.● DC version available.● Measure phase to phase.● Hi immunity to interference fields.● Suitable for indoor and outdoor use.● Current is limited to ±1 milli-ampere.● Grounded or ungrounded systems.● Meets IEC 61481 (excludes PC44K).
-
product
Power Supplies And Loads
Power Supplies and Loads power devices under test (DUTs) such as RF power amplifiers and cellular handsets. The power supply takes in AC power and delivers DC voltage with a fixed polarity, either positive or negative, to its load.
-
product
Mini Coax, Contact, ITA, one .025"
610103150
Mini Coax, Contact, ITA, one .025" Round Post/ one .02" Square Post/ .075" Spacing.Specifications Characteristic Impedance 50 OhmsFrequency Range DC to 1 GHzInsertion Loss 1.2 dB @ 1 Ghz1.02 dB @ 500 MhzVSWR ≤ 1.06 @ 1 GhzOperating Voltage & Current 0.5 Amps Max. ContinuousMating Force 1.5 lbs Max [0.68Kg]Dielectric Withstanding Voltage (DWV) 1500 VDC Min.Insulation Resistance 1000 MOhms Min.Contact Body Shield – BrassCenter Conductor – BeCuContact Plating Shield – 50µ" Au over 100µ" NiCenter conductor – 60µ" Au over 100µ" NiCycle Life 20,000 Cycles
-
product
AC Quantum Voltmeter
are based on a programmable Josephson voltage standard chip and are used for high-precision voltage measurements in the range from dc and ac to kHz frequencies.
-
product
Transmission Line Probes
Transmission line probes are a special type of passive probe designed for use at very high frequencies. They replace the high impedance probe cable found in a traditional passive probe with a precision transmission line, with a characteristic impedance that matches the oscilloscope input (50 Ohm). This greatly reduces the input capacitance to a fraction of a picofarad, minimizing the loading of high frequency signals. A matching network at the tip increases the DC input resistance. While they have lower DC input resistance than a traditional passive probe (usually 500 Ohm) to 1kOhm), the input impedance of these probes remains nearly constant over their entire frequency range. A traditional /10 passive probe will have a 10 MOhm) input impedance at DC, however this impedance drops rapidly with frequency, passing below the input impedance of a transmission line probe at less than 100 MHz.
-
product
Solid State Relays
Panasonic Automotive & Industrial Systems Europe GmbH
DC high powerLED indicationInternal diodeTerminal coverWide range input
-
product
High Voltage Tester
The AC /DC High Voltage Test Set that we offer to our clients is widely used at electrical maintenance departments and workshops. It is chiefly used to perform routine maintenance of numerous electrical devices and equipment. Apart from that, this product is used to check the quality of insulation provided in any electrical device.
-
product
Standard 3.00 (85.00) - 6.00 (170.00) Non Replaceable General Purpose Probe
G-S-R
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 30Test Center (mil): 125Test Center (mm): 3.18Full Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 67Recommended Travel (mm): 1.70Overall Length (mil): 780Overall Length (mm): 19.81Rec. Mounting Hole Size (mil): 86Rec. Mounting Hole Size (mm): 2.18Recommended Drill Size: #44
-
product
Coaxial Switch, DC to 20 GHz, SPDT
8765B
The Keysight 8765B offers excellent electrical and mechanical performance with broadband operation, high isolation, low SWR, long life, and exceptional repeatability.
-
product
Waveguide Harmonic Mixer, 33 to 50 GHz
11970Q
The Keysight 11970Q waveguide mixer is a general-purpose harmonic mixer employing a dual-diode design to achieve flat frequency response and low conversion loss. These are achieved without external dc bias or tuning stubs. Manual operation and computer-controlled hardware operation are simplified because mixer bias and tuning adjustment are not required.
-
product
Dc Watt Meter For DC Current Measuring
IM1401
Our product range includes a wide range of dc watt meter for dc current measuring.
-
product
Differential Probe
DP-800HS
*1:1 High Sensitivity*100 Gain Design*x1, x10, x100 Attenuator*Bandwidth: DC-50MHz*Input Impedance 3MΩ // 2.5PF*Max. 800Vp-p Input or ±400V DC or AC 280V RMS*Output Impedance 50Ω
