-
Product
PXI Single 6-Channel 30A Solid State MUX
40-667-012
Multiplexer Module
The 40-667 is a high current multiplexer available in dual 3-channel or single 6-channel configurations occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 30A of continuous current and switch up to 40V signals. The switches can sustain inrush currents in excess of 120A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
RMS to DC Converters
-
RMS-to-DC converters manufactured by Analog Devices are used in a wide variety of applications where precision and low power measurement of ac signals is the prime objective. An ADI rms-to-dc converter offers real time measurements, meaning there are no latency issues such as those that limit the frequency response of other technologies—the dc output is simply the equivalent of the rms input, over a wide range of input frequencies, and for complex waveforms not limited to sine waves. ADI offers a wide range of rms-to-dc converters optimized for the most demanding performance, power, and cost applications satisfying true rms needs.
-
Product
H.V. Probe Meter
PD-40AM
-
Standard Electric Works Co., Ltd
● Measures positive polarity DC voltages up to 40kV.● Lightweight and rugged.● 2 available contact tips: round needle tip for normal use and a special flat spring-type for CRT anode.● Are typically used to measure high voltages in TV sets, power supplies and instruments in laboratories.
-
Product
PXI General Purpose 2A Relay Module 16xDPST
40-132-102
Relay
Pickering Interfaces 40-131/132 modules are a range of low cost, general purpose electromechanical relay cards. They are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching cards do not have sufficient voltage or current carrying capability. Applications include the switching of medium power AC and DC loads, or slave switching larger relays, contactors or solenoids. Connections are made to the card via a front panel mounted 78 pin D-Type connector plug.
-
-
Product
High-Voltage DC Power Supplies
-
Higher-voltage and Higher-power Supplies require more complex design solutions. The heat to be dissipated and installation infrastructure, plus choice of insulation system in a HVPS are driven by the output voltage and output power which ultimately dictates packaging. Typical insulation systems are based on air, dielectric oil, epoxy, RTV Silicone and even Sulfur Hexafluoride (SF6). The method of cooling is a factor as well, the choices often coming down to air, water or oil, depending on the platform design requirements. These applications require Excelitas' detailed understanding to help choose the best design solution.
-
Product
RF / MW switch
-
The RF / MW switch includes a variety of RF and microwave switch modules - RF multiplexers, which are available for use in the 34980A multifunction switch / measurement unit, providing broadband switching from DC to 20GHz . Use these modules to route test signals between your device under test and a signal source, oscilloscope, spectrum analyzer, or other instrument. The switch / attenuator driver module also controls the external switches and attenuators of the 34980A.
-
Product
CAMAC To NIM Power Adapter
-
Power adapter to use a NIM module within a CAMAC crate. Provides all 6 voltages to the NIM module. Available also in a versions with 12V DC-to-DC converter for CAMAC chassis without +/-12V.
-
Product
L Band Splitter, DC Block All Ports
PD5182
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.6 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)50 VDC maximum on DC block portsTri Alloy SMA Female (Jack) Low PIM
-
Product
PXI Dual 3-Channel 10A Solid State MUX
40-666-011
Multiplexer Module
The 40-666 is a high current multiplexer available in dual 3-channel or single 6-channel configurations occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive. Note: The 40-666-011 supersedes the 40-666-001 which is functionally the same but with some changes in specification. A data sheet for the 40-666-001 can be found in the40-666/667 User Manual.
-
Product
LXI WTB Probe, Thru connect, DC coupled
60-981-001
-
The 60-981 LXI Wired Trigger Probe provides a simple method of monitoring the LXI Wired Trigger Bus activity. It provides a through line active probe that can be used to non-intrusively monitor the waveforms of the M-LVDS drivers on all 8 channels. Each channel has two single ended outputs from the differential pair that can be subtracted by an oscilloscope to display each driver output and the differential signal.
-
Product
Solenoid Valve Tester
DZ800
-
Shanghai Aoboor Electric Co., Ltd.
Insulation resistance, HIPOT, coil DC resistance, turn to turn surge tests can be automatically completed in one time. Applicable to electrical performance test of solenoid valves, changeover valves
-
Product
Ultra Stable Current Sources
6623A-PCS
-
Guildline Instruments 6623A-PCS Series of DC Precision High Current Systems introduces new patented designs to provide the best uncertainties of any DC high current sources (i.e. typically < 5 ppm at 1000 A) and the best in modularity.
-
Product
PXI 16xSPST 16A Power EMR Module
40-161-001
Relay
These Power Relay Modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. The 40-161 is ideal for switching up to 16A in both AC and DC applications.
-
Product
AC Insulation Testing
-
AC insulation tests are a popular response to the increasingly demanding industrial, power and domestic marketplaces. Insulation materials have had to become more efficient to keep up with demand; more efficient equipment requires less insulation material to meet the minimum acceptable value of insulation resistance. In turn, cables have become smaller and lighter. However, under certain higher stress testing conditions such as DC testing, cables like Crossed Linked Polyethylene (XLPE) can quickly degrade.
-
Product
Coaxial Termination, DC to 2 GHz
909C
Terminator
The Keysight 909C is a precision, low-reflection dc to 2 GHz load for terminating a 50-ohm coaxial system in its characteristic impedance. It is intended for use as a calibration standard. The Keysight 909C may be ordered with an APC-7, type-N male, or type-N female connector.
-
-
Product
DC - 12 GHz Packaged High Efficiency Divide by 8 Prescaler
HMMC-3128-BLK
Frequency Divider
TheHMMC-3128-BLK is a packaged DC - 12 GHz divide by eight prescaler designed for use in high frequency communications, microwave instrumentation, and EW radar systems where low phase-noise PLL control circuitry or broadband frequency translation is required.
-
Product
Current Transformer
-
A precision electrical device used to step down high alternating (AC) or direct (DC) primary currents into safe, measurable secondary values for power analysis, energy management, and monitoring instruments.
-
Product
1 Mm Calibration Kit
85059B
Mechanical Calibration Kit
The Keysight 85059B is a 1.0 mm calibration kit designed for vector network analyzer systems operating over the frequency range of DC to 120 GHz. The opens, shorts and loads in this kit are optimized to provide accurate and traceable calibrations over the specified frequency range. The 85059B with 85059V 1 mm Verification kit are replacements for the 85059A 1 mm calibration/verification kit.
-
Product
High-Performance Autoranging DC Power Module, 20V, 50A, 300W
N6753A
Power Module
The Keysight N6753A is a high-performance, autoranging DC power module that offers speed and accuracy for test optimization.
-
Product
Digital Multimeter
MM-2
-
Our compact, low cost Model MM-2 Digital Multimeter with True RMS is ideal for general electrical testing and troubleshooting. This full function multimeter measures DC voltage to 1000 V and AC voltage to 750 V, DC and AC current to 10 A and resistance to 400 Ohms. In addition to volts, amps and ohms, this meter includes audible continuity, diode, LED and transistor hFE tests. The rotary switch allows you to select from any of the functions quickly and easily.
-
Product
Adapter/Stainless Steel
WADP-QNMNF-01
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
Clamp Meter, Auto, Average, 1 kA AC, 600 V AC, 600 V DC, 46 mm Jaw Opening Max.
72-6130
-
A clamp-on type test meter with AC/DC voltage and AC current measurement.
-
Product
Five Channel Amplifier
-
Teledyne RF & Micrrowave designed the Five Channel Amplifier specifically for a custom space application. Each independent channel used dedicated RF Input/Output and DC bias connections. Each channel's RF performance was tailored differently to meet the application requirements. All components were manufactured and screened per MIL-PRF-38534, Class K. Additionally, to meet mission requirements The top assembly was also tested for RF and DC parameters during MIL-STD-202 thermal cycling and random vibration environments. This effort required disciplined development, manufacturing and program management efforts to meet challenging mechanical and RF engineering requirements.
-
Product
Cable and Harness Tester
CHT
-
The Cable and Harness Tester (CHT) provides multiple testing capabilities for up to 300 connector/harness test points. Test capabilities include DC Insulation Resistance (IR), DC and AC Dielectric Withstanding Voltage (DWV), and 2-Wire and 4-Wire Continuity.
-
Product
Specialty/Custom Load Banks
XLHV Medium Voltage Series
-
Mosebach Manufacturing Company
The XLHV range offers you a continuous load at higher voltages in an outdoor rated enclosure. These can be for AC or DC load banks up to 15kV.
-
Product
Micropositioner
-
Our broad range of micropositioners fill requirements for probing for different measurement applications as well as measurement environments. For example, a measurement system focused on cryogenic environments would not use the same product for room temperature probing. Likewise, a DC micropositioner is unfit for mmW measurement applications.
-
Product
Precision Pulsed Current Sources
SpikeSafe Performance Series
-
SpikeSafe™ Performance Series Current Sources supply DC and precision continuous or single pulse current for light measurement and other applications. With sustained output power and no duty cycle limitations, Performance Series Current Sources support a broad range of applications.
-
Product
DC Electronic Load
Model - KM-mPD-501
-
Kusam Electrical Industries Limited
KM-mPD-501 DC electronic load mainly focuses on the testing of power circuit on PCB. KM-mPD-501 offers a solution for function test of Switch step up, Stepdown, Regulators and Driver IC . Engineer puts components, such as CPU, DSP, FPGA; etc on a PCB after the power circuit has been tested. It’s not complete to use a meter to measure the voltage. KM-mPD-501 offers engineer OVP, OCP and OPP functions that help engineer know the value of overload current . On the other hand, engineer can use a programmable DC power supply (mPP series) to offer external power and connect PCB’s output to KM-mPD-501. Then engineer can easily get output watt, figure out the efficiency of power circuit and check if inductances, capacitances and resistances perfectly work with the power circuit. KM-mPD-501 not only offers loading emulation of current but also provides OVP and OPP. User can use these functions to test solar power battery, rechargeable battery and motor driver. In school laboratory, KM-mPD-501 helps students do experiment on power circuit, linear circuit and driver circuit.
