Quartz Crystal Microbalance
-
Product
Quartz Crystal Microbalance
QCM200
-
Stanford Research Systems, Inc.
The QCM200 Quartz Crystal Microbalance measures mass and viscosity in processes occurring at or near surfaces, or within thin films. This system includes a controller, crystal oscillator electronics, crystal holder, three quartz crystals, and Windows / Mac software.
-
Product
Quartz Crystal Microbalance
-
Determining moisture concentration in natural gas, industrial gases or process gas is critical to many applications. QCM and electrolytic analyzers deliver fast, reliable and cost-effective measurements that support these processes.
-
Product
Differential Quartz Crystal Microbalance
Dike
-
During an experiment to detect an affinity reaction on biological material, a molecule of interest is attached to the quartz crystal of the measurement channel, this deposition can be achieved by direct binding or by capture through another protein, the result of this process is to make the quartz sensitive to the molecule to be detected.
-
Product
Open-Source Quartz Crystal Microbalance
-
The sensor is a surface sensitive quartz crystal capable of measuring phenomena at molecular scale. It works in vacuum, air and liquid environments. The QCM sensor is based on the piezoelectric properties of the quartz crystal. The application of an alternating current causes the mechanical vibration of the quartz crystal in the MHz range. The QCM technique measures the variations in quartz frequency for measuring the mass variations on its surface.
-
Product
Time-Resolved Electrochemical Quartz Crystal Microbalance
400C Series
-
The quartz crystal microbalance (QCM) is a variant of acoustic wave microsensors that are capable of ultrasensitive mass measurements. Under favorable conditions, a typical QCM can measure a mass change of 0.1-1 ng/cm2. QCM oscillates in a mechanically resonant shear mode under the influence of a high frequency AC electric field which is applied across the thickness of the crystal. Figure 1b below shows an edge view of a QCM crystal undergoing oscillatory shear distortion. The central portions of the top and bottom of the crystal are coated with a typically disk-shaped thin metal film (e.g., gold).
-
Product
Flow Cell Kit
QCMT
-
The quartz crystal microbalance (QCM) technique under electrochemical frequency is very useful to determine many compounds such as metal proteins, metal ions and thiol-conjugated oligonucleotides.
-
Product
EQCM Electronic Quartz Crystal Microbalance
Elettra
-
Elettra has been designed to operate on its own, but it is also possible to connect it to a PC to control it and acquire, view and save data thanks to its extremely easy to use software that runs under MS-Windows™. The data acquisition process can be controlled extremely quickly thanks to the PLAY, PAUSE and STOP keys.
-
Product
Nanogravimetric Measuring Instrument
EUREKA
-
Eureka is a QCM / EQCM (Quartz Crystal Microbalance) nanogravimetric measuring instrument capable of mass measurements in the order of nano-grams and pico-grams. Eureka can be used with gas and liquids, the cells are made by BioAge and sold with the instrument. The tool is the most versatile among those existing on the market, with an excellent quality / price ratio. It is a portable instrument as it is powered only by the PC USB port.
-
Product
Moisture Analyzer Series
3050
-
The 3050 series of moisture analyzers utilizes AMETEK’s proven, accurate quartz crystal microbalance (QCM) technology. Built-in verification provides operators with increased measurement confidence.
-
-
Product
Electro-Optic DSTMS Crystals
-
DSTMS and other high-quality organic crystals are produced and optically prepared in the facilities of Rainbow Photonics in Switzerland.
-
Product
3-Component Quartz Force Rings
260 Series
-
Three-component quartz force ring sensors are capable of simultaneously measuring dynamic force in three orthogonal directions (X, Y, and Z). They contain three sets of quartz plates that are stacked in a preloaded arrangement. Each set responds to the vector component of an applied force acting along its sensitive axis. 3-component ring force sensors must be statically preloaded for optimum performance. Preloading provides the sensing elements with the compressive loading required to allow the proper transmission of shear forces. Versions are available with ranges up to 10k lb (45k N) in the z-axis (perpendicular to the top surface), and up to 4000 lb (18k N) in the x-and y (shear) axes. Both ICP® and charge output styles are available.
-
Product
Quartz Crystals
-
Quartz crystal resonators are used in a wide range of electronic applications that require timing devices. The quality of the quartz crystal blank is critical to the performance of quartz crystal units and the high Q factor of quartz means that tight stabilities can be achieved; this is key to ensuring microprocessor timing circuits work correctly within customer’s designs.
-
Product
Oven Controlled Crystal Oscillators
OCXOS
-
Oven Controlled Crystal Oscillators (OCXOs) deliver the ultimate piezo electric performance with stabilities down to less than ±1ppb. An OCXO offers frequency stabilities even tighter than those offered by a TCXO.
-
Product
Phase-Locked Crystal Oscillator
PLXO Series 0.9” x 0.9” x 0.25”
-
*Compact Surface Mount Package *Excellent Phase Noise and Stability *Configurable for any application
-
Product
voltage controlled crystal oscillator
VCXO
-
A VCXO (Voltage Controlled Crystal Oscillator) is a crystal oscillator the output frequency of which is controlled by adding an external control voltage via a frequency control input on a variable capacitance component such as a varactor diode connected in parallel to a load capacitance (CL). Epson VCXOs are divided into two types according to Voltage-Frequency (V-F) characteristic slopes depending on the AFC (Automatic Frequency Control) input configuration of the VCXO. One is a VCXO with a positive V-F slope and the other is a VCXO with a negative V-F slope. Please note that the input voltage of a control circuit will vary according to the individual type, as shown in Figs. 3 and 4. Epson's VCXOs are capable of either, depending on the customer's preference. Epson's VCXOs have been increasingly used for broader applications such as slave oscillators in phased-lock loops, or frequency modulators. Among the above types, a VCXO combined with a TCXO is called a VC-TCXO , respectively. These components have the merit of delicately controlling their output frequency electrically.
-
Product
Quartz ICP® Force Rings
-
Ring-style sensor configurations measure dynamic compression. Tension measurements are also possible if the unit has been installed with proper pre-load. The through-hole mounting supports platform, integrated link, and support style installations using either a through-bolt or the supplied stud.
-
Product
1HZ~100MHZ Crystal Oscillator Tester
CX-118A
-
Shenzhen Chuangxin Instruments Co., Ltd.
1 It's using reciprocal counting technique, high accuracy, wide measuring range, truly equal precision measurement, fast speed measurement, high sensitivity.2 single-chip microprocessor technology cycle frequency measurement and intelligent management, making the instrument has high reliability and excellent performance / price ratio.3 It's using LSI design, the use of CPLD devices, instrument components greatly reduced, reliability has been greatly improved, the average time between failures ≥10000h.The machine looks nice, small size, light weight, easy to use.
-
-
Product
Liquid Crystal Thermographic Analysis Tool
thermVIEW
-
Advanced Thermal Solutions, Inc.
thermVIEW is a high resolution liquid crystal thermography system for cost effective temperature measurement of electronic circuit boards, micro circuits, hybrid components and integrated circuits. One micron level* thermal mapping of electronic devices.
-
Product
General Purpose Quartz Force Sensors
-
General purpose force sensors are offered in either stud or axial mounted configurations. They are internally pre-loaded and can be used for dynamic compression, tension, and impact force measurements. Tapped mounting holes on both ends of the radial connector style support link, platform, integrated link, and free-standing installations. The axial mounted type offers protection of the electrical connector and sensor cable from potential damage during drop testing and in free-standing installations. Supplied impact caps facilitate impact and drop force measurements.
-
Product
Crystal Vibration Tester 1HZ~100MHZ
-
Shenzhen Chuangxin Instruments Co., Ltd.
1 It's using reciprocal counting technique, high accuracy, wide measuring range, truly equal precision measurement, fast speed measurement, high sensitivity.2 single-chip microprocessor technology cycle frequency measurement and intelligent management, making the instrument has high reliability and excellent performance / price ratio.3 It's using LSI design, the use of CPLD devices, instrument components greatly reduced, reliability has been greatly improved, the average time between failures ≥10000h. The machine looks nice, small size, light weight, easy to use.
-
-
Product
Electro-Optic OH1 Crystals
-
OH1 and other high-quality organic crystals are produced and optically prepared in the facilities of Rainbow Photonics in Switzerland.
-
Product
Single Crystal Films
YIG
-
Due to their very low microwave losses, single crystal ferromagnetic materials such as Yttrium Iron Garnet (YIG) and doped YIG are used for devices in microwave technology.
-
Product
Quartz Charge Force Rings
-
Ring-style sensor configurations measure dynamic compression. Tension measurements are also possible if the unit has been installed with proper pre-load.
-
Product
3-Component Quartz Force Rings And Links
-
Three-component dynamic force sensors are offered in both ICP® and charge output configurations for dynamic and quasi-static force measurement applications. Each utilizes an array of precision aligned, quartz sensing crystals. Measurements along the z-axis are proportional to applied compression, tension and impact forces. Measurements along the x and y axes are proportional to shear forces that are imposed upon preloaded crystals by the test fixture.
-
Product
Temperature Compensated Crystal Oscillators
-
Temperature Compensated Crystal Oscillators by Pasternack
-
Product
Miniature Quartz Force Sensors
-
Often the test engineer will try to take low level measurements with a sensors not rated for these low levels. Due to insufficient sensitivity the resulting data may be noisy, hard to analyze or unusable. Using the appropriately sized and ranged PCB Miniature Quartz Force Sensor solves the problem and gives reliable data at a Low Amplitude level. The miniature sensor configuration permits low-amplitude, dynamic compression, tension, and impact force measurements.
-
Product
SOSA Aligned 1-Slot 3U VPX Development Chassis for Quartz Products
Model 8257A
-
- Ideal development platform for Mercury's- Model 5553 8-Channel A/D & D/A Zynq UltraScale+ RFSoC Gen 3 - Processor - SOSA Aligned 3U VPX- Model 5550 8-Channel A/D & D/A Zynq UltraScale+ RFSoC Processor - SOSA Aligned 3U VPX- Access to data and control planes provided through RTM- 1-slot, small footprint development chassis- Rear panel access to RF I/O, 100 GigE and chassis manager- Supports VITA-67.3C- Compatible with the Quartz product family- Pentek's Quartz Family of Xilinx Zynq UltraScale+ RFSoC FPGA Products Video- Live Signal Acquisition Video: Quartz Model 5950 and Model 6001 RFSoC boards- Pipeline Newsletter: Strategies for Deploying Xilinx's Zync UltraScale+ RFSoC- Please refer to the product datasheet for Installed FPGA IP Module details
