ADC
quantization of an analog signal into a digital signal.
See Also: Analog-to-Digital Converters, FPGA, Transducers
-
Product
RF Milliwatt Meters
Type NDB-2 and NDB-3
-
National RF’s Type NDB-2 and NDB-3 RF Milliwatt Meters are affordable pieces of test equipment for both the RF laboratory and the home experimenter. Both provide a digital reading of RF power in dB reference 1 milliwatt of power into a 50 ohm load (i.e. 0 dBm). The circuitry consists of a low noise logarithmic amplifier that drives a digital A/D converting meter circuit. The lowest power levels that can be read are about –73 dBm (approximately 40 microvolts or .00000003 milliwatts). The maximum power input should not exceed 10 milliwatts (+10 dBm or .010 watts) when inputed without attenuation. An internal attenuator is provided and described in the next section.
-
Product
4-Wire Resistance Measurement | Continuity & HiPot Cable & Wire Harness Testers
-
An add-on option for the CableEye HVX high voltage cable tester series that permits expanded testing for contact and wire resistance as low as 1 mΩ. After checking for opens, shorts, miswires, and resistance limits, the 4-wire Kelvin measurement applies a user-selectable test current from 10 mA to 1 A to determine connection resistance within 1 mΩ. The resistance profile of a model cable may be stored and used as a basis of comparison during later testing to reveal cold solder joints, faulty crimps, recessed pins, pin contact contamination, improper wire gauge, and stress-extruded wire.This option may be purchased with any new HVX tester, or added as an upgrade to any of your existing HVX testers.
-
Product
4-Channel, Sigma-Delta ADC Function Card
ProDAQ 3430
-
The ProDAQ 3430 is a 4-channel, sigma-delta ADC function card. Every channel contains front-end conditioning circuitry followed by a sigma-delta ADC. The bit stream from every ADC is then directed to finite impulse response (FIR) decimation filters. Users can activate up to 10 stages of the FIR filters. The filtered data from the selected stages is then stored in the FIFO. The data from the FIFO easily can be moved on-the-fly to the motherboard or to the host.
-
Product
Conductivity Detector
CDD-10AVP
-
Low noise, low drift and wide dynamic range assure proven performance of the Shimadzu VP series HPLC. Data acquired by the CDD-10AVP is transferred to the SCL system controller via an optical fiber interface and are digitally processed by workstation. By adding the optional cell (dual kit NS), a low-cost and compact non-suppressor type dual ion chromatograph, which detects anions and cations simultaneously, can be made.
-
Product
RS-232 to EIA-530 Interface Converter
Model 62-1 / 62-2
-
FEATURES: Supports 10 Category I & 3 Category II Circuits; Full EIA-530 & RS-422 Compliance; DTE & DCE Models; Meets MIL-STD-188-114 Type 1/2; Up to 256 KBPS Data Rate. Conversion between RS-232 and EIA-530 is accomplished by the Models 62-1 and 62-2. These devices provide conversion for the entire EIA-530 interface which includes ten Category I circuits and three Category II circuits.
-
Product
DC/DC Converter 3.5 W
REM3.5E-2415S/R6/A/SMD
-
DC/DC converter with 3.5 W from Recom | input ranges 18 - 36 VDC | output 15 V | operates in ambient temperature from -40 to +95 °C | SMT package
-
Product
Wet Oxidation TOC Analyzer
TOC-VWP
-
Phosphoric acid and the oxidant (persulfate) are added to the sample, which is heated under UV illumination to convert the TC in the sample to carbon dioxide. This carbon dioxide flows with the carrier gas via the dehumidifier into the NDIR sample cell. The area of the carbon dioxide peak signal is measured and this peak area is converted to TC concentration using a pre-prepared calibration curve.
-
Product
ARINC PCI Express One Lane Interface Card
PCIE1L-A429
Interface Card
The ARINC PCIE1L-A429 Interface Card and AltaAPI Support Software Represent the Latest ARINC 32-bit FPGA Protocol Engine Technology. Encode and Decode almost Any ARINC-429 PHY Level Label/Word Signal. The First Card in the Industry to Offer Advanced Test Functions of Signal Generation and A/D Signal Capture. The one lane card PCIe is the industry first low profile
-
Product
100-Watt DC Power Line Conditioner w/Holdup
44LS1
Power Line Conditioner
NAI’s 44LS1 is a 100-Watt Power Line Conditioner with holdup time that protects downstream DC/DC converters from transients, low voltage conditions, and power interruptions. This unit accepts +28 VDC input and provides 22.5 to 30 VDC at 100 Watts to all downstream DC/DC converters.
-
Product
Paddlewheel Flow Sensor
2537
-
The Signet 2537 Flow Sensor is the next generation in fluid measurement technology from the inventor of the original paddlewheel flowmeter. This sensor is an enhancement on what is already an industry standard. It has the added functionality of various output options including flow switch, pulse divider, digital (S3L) or 4 to 20 mA. Additionally, it offers low flow, low power and high resolution and can be configured on-site directly through the built-in user interface.
-
Product
Counter/Timer Board
USB-CTR-15
-
The USB-CTR-15 is an ideal solution for adding portable, easy-to-install, counter/timer capabilities to any PC or embedded system with a USB port. This board is packaged in a small, rugged, industrial enclosure and features 15 independent 16-bit counter/timers. The unit is a true USB 2.0 device, offering the highest speed available with the USB bus. It is fully compatible with both USB 1.1 and USB 2.0 ports. The unit is plug-and-play allowing quick connect/disconnect whenever you need additional counter/timer devices on your USB port. The USB-CTR-15 can be used for a wide variety of measurement applications including event counting, frequency measurements, position measurement, pulse counting, pulse-width modulation and pulse generation. The OEM version provides just the board without the enclosure or external screw terminal board and is ideal for a variety of embedded OEM applications.
-
Product
Digital Power Meter
66205
Power Meter
The 66205 is the 2nd generation of the 66200 series power meter designed specifically for single channel measurement. Its state of art design is capable of providing highly accurate power measurements to meet the requirements of IEC 62301/EN50564 standards. Functionality improvements of the 66205 increase power measurement capabilities to a wider range of applications. The Smart Range function is one of the most important new features added to the 66205 power meter. Smart Range allows the power integration mode to perform active power measurements with the measurement range in auto mode. Chroma’s proprietary design automatically selects the appropriate range, based on changes in sensed voltage and current, ensures the best accuracy when integrating the measurements over time. The 66205 provides 10 selectable current measurement ranges from 5mA up to 30A. External sensor options A662017~A662020 are available to increase the current measurement range. Six selectable voltage ranges are available up to 600V.
-
Product
Switches
-
As your partner in embedded solutions, we understand that most military and industrial customers need different products than their commercial world counterparts–switches are no exception. We manufacture layer 2 and layer 3 switches with added security options to ensure that your network components are always protected.
-
Product
Multifrequency Clock Synthesizer - PMC
Model 7190
-
- Simultaneous synthesis of up to 5 different clocks- 8 SMC clock outputs- Ideal for A/D and D/A converter clock sources- Typical phase noise: -125 dBc/Hz @ 1 kHz offset- All clocks are phase-locked to input reference signal- Input reference frequency of 5 or 10 MHz- Four quad VCXOs allow selection from 16 different base frequencies- Output clocks of 1, 2, 4, 8, or 16 submultiples of VCXO base frequencies- Output clock frequencies between 50 and 500 MHz- Control and status via PCI bus interface
-
Product
Mini Media Converter Chassis
1 RU 19"
-
The Media Converter chassis is capable of housing up to 12 mini media converters. You can start with a single media converter, and grow to 12 Media Converters
-
Product
Model LP: Lumber & Plaster Moisture Meter
MRC006504
-
Offers the same ad the Model L plus spring-loaded electrode buttons for testing irregular, flat, and curved surfaces. Allows moisture comparisons between kiln decks. Tests 1/4" (6.4mm) to 3/4" (1.9cm) thick wallboard and plasterwork.
-
Product
CoreAFM - the best value research AFM
CoreAFM
-
The fusion of a modern flexure-guided scanner, XYZ sample stage, camera, active vibration isolation table, and acoustic shielding in a single all-in-one unit results in a complete AFM system with an unparalleled compact footprint. The system comes with a fully digital 24-bit controller developed specifically for the CoreAFM scanhead. All the essential functions of modern AFM are integral components of the CoreAFM system; all you need to do to take the CoreAFM into operation is connect the controller, and plug in power and USB.State of the art electronics with 24-bit ADC and DAC ensure high-resolution XYZ driving of the 100×100×12 µm scanner and allow for low-noise force detection limited only by the cantilever. Thirty-two standard and optional modes with fully compatible add-ons make the CoreAFM the tool of choice for applications ranging from materials research to life science and electrochemistry. Starting from the basic CoreAFM system, its functionality can be seamlessly extended
-
Product
Power Converter Test Solution for HEV/EV and HEMS
EV1003A
Power Sensor
The hybrid-electric and electric vehicle (HEV/EV) market has been growing rapidly. The addition of these vehicles in the automotive market brings with them new challenges in design and manufacturing. Probably the most noticeable change is the addition of high-voltage, high-power batteries to a platform that is traditionally 12 volts. Hybrid electric and full electric vehicle batteries are 300 volts and higher. These high voltages bring with them additional costs and risks.
-
Product
DCDC
SC10A Series
-
The SC10A series of cost sensitive single and dual output 10 watt DC/DC converters are specifically designed for critical applications requiring a compact, low profile case.
-
Product
SparkFun BabyBuck Regulator Breakout
3.3V (AP63203)
-
Who doesn't occasionally need power regulation? We certainly do, so we've designed the SparkFun BabyBuck Regulator Breakout to help us with just such a task. Featuring the AP63203 from Diodes Inc, this breakout board takes advantage of a 2A synchronous buck converter that has a wide input voltage range of 3.8V to 32V and fully integrated 125mΩ high-side power MOSFET/68mΩ lowside power MOSFET to provide high-efficiency step-down DC/DC conversion. All of this snuggled up in a low-profile, TSOT26 package that's integrated into a 0.4in by 0.5in board.
-
Product
Mezzanine System
5147
System
ECM P/N 5147 provides two channels of 12 bit A/D conversion using the Analog Devices AD9235, and is suitable for medium resolution high speed applications. The two differential inputs are terminated in 120 ohms and buffered with a gain of 1 differential amplifier. Differential Input range is +/-3.0V. Sample rates are 20MHz per channel with a 5MHz 4 pole elliptical analog input filter.
-
Product
- RS-485 to Fiber Optic Converter
Model 276A
-
FEATURES: Data Rate to 1 MBPS; ST Connectors; DB-25 Connector; Half-duplex operation; Extends distance of RS-485 network to 6,600 ft (2 km) on multimode fiber cable. The Model 276A provides the capability of transmitting an RS-485 signal via a fiber optic link.
-
Product
Phase Noise Measurement Solution, 50 kHz to 110 GHz
E5505A
-
The Keysight Technologies E5500 Series of phase noise measurement solutions offers the most flexible set of measurements on one-port VCOs, DROs, crystal oscillators and synthesizers. Two-port devices, including amplifiers and converters, plus CW, pulsed and spurious signals can also be measured. The E5500 measurements include absolute and residual phase noises, AM noise, and low-level spurious signals. The stand-alone instrument architecture easily configures for various measurement techniques, including the PLL/reference source technique, residual and FM discriminator methods.
-
Product
PSG RF Analog Signal Generator, 100 kHz to 9 GHz
E8663D
Signal Generator
Tackle demanding radar & satcom measurements with metrology-grade performance, including high output power & superior level accuracyUse as an ideal reference in phase noise test systems or for analog-to-digital converter testing with the lowest phase noise in a commercial sourceCharacterize devices & circuits by adding AM, FM, M & pulse modulation to your signalImprove existing test system performance: E8663D is built on the outstanding legacy of the 8663A & is fully code compatible
-
Product
Quadrature Digital Up Converters
QDUC
-
Analog Devices digital up/downconverters serve as the frequency translator and digital filter between data converters and DSP blocks. These innovative products enable highly programmable and configurable receive and transmit signal chains, allowing multichannel, multicarrier radio platforms in 3G wireless base stations. They also meet the digital data conversion requirements for many other communications applications.
-
Product
RF Acquisition Record and Playback Instrument
SARP-6
-
Saluki SARP-6 RF Signal Acquisition Record and Playback Apparatus is a portable RF signal acquisition record playback equipment. It can be used to directly acquire, record, and playback RF signal from 1MHz to 6GHz. Its data recording and bandwidth playback can reach 200MHz. The SARP-6 RF Signal Acquisition Record and Playback system is composed of up and down inverter module, high-performance ADC and DAC, and large capacity solid-state FLASH or high-performance disk. It is widely used in radar, GPS, communication, telemetry, as well as many other circumstances for civil purposes when acquiring signal and recording it down.Applications: Interference Analysis/Surveillance/Spectrum Management/Satellite Communications
-
Product
PCIe 3.0 Protocol Analyzer
Summit T3-8
Protocol Analyzer
PCIe 3.0 technology achieves twice the effective data throughput rate of the PCIe 2.0 standard through a combination of increased data bit rate (5 GT/s moving to 8 GT/s) and the elimination of 8b/10b data encoding, which previously added an overhead of 20 percent to all data transfers. In eliminating 8b10b encoding, PCIe 3.0 technology now relies on the existing data scrambling techniques similar to those used for PCIe 2.0 technology to ensure that receivers maintain lock on the incoming data stream.
-
Product
NI-5731, 40 MS/s, 12-Bit, 2-Channel Digitizer Adapter Module for FlexRIO
781657-02
Digitizer
The NI‑5731 is a digitizer adapter module that, when combined with a PXI FPGA Module for FlexRIO, creates a high-speed digitizer that simultaneously samples two channels at 40 MS/s. You can use the NI‑5731 to do real-time processing and streaming of analog data with high-performance A/D converters. The NI‑5731 also includes selectable elliptic, Bessel, and bypass hardware filters. The Digitizer Adapter Module for FlexRIO is ideal for applications that require in-line data processing, high data streaming rates, and deployed high-performance solutions.
-
Product
Web Sensor with PoE
T3610
-
PoE Web Sensor with built-in relative humidity and temperature sensors. High precision capacitive polymer sensor ensures excellent long term calibration stability and ultimate accuracy. Dual line LCD is an advantage. Power over Ethernet feature according IEEE 802.3af is supported. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio and specific enthalpy.
-
Product
Adaptive Relay, Virtex-6 FPGA - XMC
Model 71624
-
- Modifies 34 IF signals between input and output- Up to 80 MHz IF bandwidth- Two 200 MHz 16-bit A/Ds- Two 800 MHz 16-bit D/As- 34 DDCs and 34 DUCs (digital downconverters and digital upconverters)- Signal drop/add/replace- Frequency shifting and hopping- Amplitude boost and attenutation- PCI Express Gen 1: x4 or x8- RoHS Compliant Lead-Free Version Available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
