ICP DAS USA, Inc.
We seek to provide our customers with cost effective, flexible, and easy to use solutions for their Data Acquisition and Embedded Control Applications.
- 1-888-971-9888
1-346-292-9998 - sales@icpdas-usa.com
- 9804 Whithorn Dr.,
Houston, TX 77095
United States of America
-
Product
Board Accessories
DN-37A (with Din Rail Mount and Male-Female D-Sub Cable)
-
DN-37 is a Screw Terminal Board for PC Based I/O Boards with or without din rail mounts. It is an I/O Connector Block with a 37-Pin I/O Connector and 37-pin CA-3710 cable.
-
Product
Relay Modules
DN-PR4/N
-
The DN-PR4 Features a DIN-Rail mount and four form C electromechanical power relays for efficient switching of load by programmed control. The contact of each relay can control a 5 A load at 250VAC/30VDC. The relay is energized by applying a +24V voltage signal to the appropriate relay channel. Each output is equipped with a LED to display their status. Each output is equipped with a varistor that shunts the surge voltage of the inductive load or electromagnetic brake to protect the relay contact point. All relay control and relay outputs are accessible through the wiring terminals.
-
Product
Ethernet/IP Data Acquisition
-
Ethernet/IP based data acquisition modules communicate over Industrial Ethernet protocol over standard IEEE 802.3 and TCP/IP protocol suites. They are available in analog and digital I/O configurations and can be integrated with standard Ethernet cabling.
-
Product
Multi-Port Serial
VXC-114U
-
The VXC-114 series card provides 4 RS-232 serial ports. It is equipped with a 128-byte hardware FIFO for each port, supports for speed up to 115200 bps and supports full-duplex communication.
-
Product
Motion, Temperature And Leak Detection Sensors
-
Select from a wide range of motion and temperature sensors for motion detection, temperature, humidity, and carbon dioxide (CO2). We carry passive infrared (PIR) sensors that detects human-body generated infrared waves to indoor motion detection. They can be configured to automatically switch on a light or trigger alarms if motion is detected. The DL-300 can also be used on mobile devices so it is easy for you to monitor your room temperature, humidity, carbon dioxide (CO2) and mono dioxide (CO) level on your phone.
-
Product
PCI Multifunction Board
PCI-1800H/S
-
The PCI-1800 series is a family of high performance data acquisition boards for PCs with a PCI bus. It features a continuous, 330KHz for low gain (44KHz for high gain), gap-free data acquisition under DOS and Windows. The PCI-1800 family has the same architecture and has two 12-bit D/A output channels, 16 digital input channels, and 16 digital output channels. The PCI-1800H, PCI-1800L provides 16 single-ended or 8 differential inputs. The PCI-1802H and PCI-1802L provide 32 single-ended or 16 differential inputs. The -H means high gain model and the -L means low gain model. The scan function of PCI-1800 is so amazing. We call it Magic Scan. The variable channel scan function is found in some famous data acquisition boards. Compared to Variable channel scan, the Magic Scan improves a lot functions and meets the demand of high end users. The Magic Scan mechanism not only scans the different input channels at vastly different rates, but also at different gain. Even in multi-channel scans, the sampling rates can maintain at 330KS/s.
-
Product
PCI Daughter Boards
DN-37-381
-
I/O Connector Block with DIN-Rail MountingTwo 19-pin headerPin to Pin screw terminal for I/O connectedPitch : 381mm(0.150inch)Dimension : 103mm x 86mm
-
Product
PCI Daughter Boards
DB-1825/1/DIN (with DIN rail mounting kit)
-
Screw terminal board using 37 pin cable I/O ports for PCI-1202/1602/1802/822/826 series , (32 channel single-ended ,16 channel differential)Blank pads for break detection, Low-pass filter , current shut and voltage divider (manual soldering)Dimensions :170 mm x 114 mm
-
Product
TET Modules
-
The tET Series tiny Modbus TCP based I/O modules provide digital I/O functions, support I/O pairing and have a din rail mount. The module can be remotely controlled through a 10/100 M Ethernet network by using Modbus TCP/UDP protocol. They are configurable through a standard web browser and are easy to use. The tET Series can be used with our FREE EZ Data Logger Software.
-
Product
CANopen Data Acquisition
-
CANopen is a network protocol based on CANBus and we offer CANopen data acquisition modules in Counter, PWM, Analog Output, Digital Input and Digital Output.
-
Product
PCI Daughter Boards
DB-8325/2 (Screw Terminal Board OEM Version)
-
Screw terminal board using 37 pin cable I/O ports for ISO-813 , PISO-813 onlyDimensions :220mmX114mm
-
Product
Board Accessories
DN-20
-
DN-20 is a Screw Terminal Board for PC Based I/O Boards with or without din rail mounts. It is an I/O Connector Block with two 20 Pin Headers.
-
Product
BACnet Data Acquisition
-
BACnet is a communication protocol for building automation and control networks. BACnet is designed to allow communication for applications such as heating, ventilating, and air-conditioning control, lighting control, access control, and fire detection systems and their associated equipment. The BACnet protocol defines a number of services that are used to communicate between building devices. Itl also defines a number of objects that are acted upon by the services. The objects include Analog Input, Analog Output, Analog Value, Binary Input, Binary Output, Binary Value, Multi-State Input, Multi-State Output, and Device, etc.
-
-
Product
MQTT Data Acquisition
-
MQTT is a method of Machine to Machine (M2M) communication by writing and retrieving application-specific data (messages) to and from queues, without having a private, dedicated connection to link them. It simplifies and accelerates the cloud-based integration of diverse applications data between IIoT devices under assured, secure and reliable exchange of information circumstance. Using MQTT in IIoT devices not only dramatically simplifies the creation and maintenance of Industrial application but also makes connectivity for the “internet of things” and mobile devices easily, and achieve the smart automation based on industry 4.0.
