Filter Results By:
Products
Applications
Manufacturers
W-LAN
Refers to wireless networks between computers within one building or a group of buildings. (lech.priv.at)
-
product
Solutions foe a Wireless Network
Bluetooth & WLAN
One wireless technology cannot cater for all application requirements. The standardized wireless technologies — WLAN, Classic Bluetooth and Bluetooth Low Energy — are good at different things
-
product
PXIe-5665, Up to 14 GHz PXI Vector Signal Analyzer
781774-03
Up to 14 GHz PXI Vector Signal Analyzer - The PXIe‑5665 is a modular, three‑stage superheterodyne analyzer that you can use as either a spectrum analyzer or vector signal analyzer. It supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. In addition, you can use the PXIe‑5665 with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5665 can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5665 provides a low-cost solution to high-performance RF measurements.
-
product
Car-to-X Signal Strength Emulator
Qosmotec Software Solutions GmbH
QPER-C2X is a special adaptation of the signal strength emulator QPER, designed for mobile and Vehicular Ad-hoc Networks (MANet and VANet). Every radio devices in such an infrastructure-less network acts as a sender, receiver, and forwarder (router). Therefore, the ports of the QPER-C2X hardware are fully connected with each other by dynamically controllable attenuators. The system is fully designed for frequencies up to 6 GHz, since wireless communication for Intelligent Transport Systems (ITS) is based on the WLAN standard IEE 802.11p from 5.850 MHz to 5.925 MHz. The connected ITS stations can be either on-board units, as they are built into cars, or road side units that are used by road infrastructure (traffic lights, road work area delimiters, velocity signs). For tests in the lab, radio modules of such ITS stations are each kept in a shielding box that prevents any unwanted radiation over the air.
-
product
Serial/Ethernet to Wi-Fi Module
SX-590-1402
The SX-590-1402 is Silex’s latest FIPS 140-2 high-performance Serial/Ethernet to Wi-Fi module that provides connectivity for low-power portable devices to 802.11 wireless local area networks (WLANS).
-
product
Electrosmog Shielding
Gigahertz Solutions is your partner when it comes to shielding against electrosmog. We offer you products for shielding high-frequency fields as well as products for reducing low-frequency fields. Regardless of whether it is WLAN radiation, mobile phone radiation, Bluetooth or 5G; In our range for shielding from electrosmog you are guaranteed to find the right product with our shielding paints, canopies and shielding fabrics!
-
product
PXIe-5665, Up to 14 GHz PXI Vector Signal Analyzer
781775-03
Up to 14 GHz PXI Vector Signal Analyzer - The PXIe‑5665 is a modular, three‑stage superheterodyne analyzer that you can use as either a spectrum analyzer or vector signal analyzer. It supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. In addition, you can use the PXIe‑5665 with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5665 can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5665 provides a low-cost solution to high-performance RF measurements.
-
product
Assess Real-World Wi-Fi Performance
IxVeriWave
Keysight Network Applications and Security
Test and validate Wi-Fi performance of WLAN networks by recreating real-world scenarios.
-
product
Peak Power Analyzer
4500C
The Boonton Model 4500C is the instrument of choice for capturing, displaying, analyzing and characterizing microwave and RF power in both the time and statistical domains. It is ideal for design, verification, and troubleshooting of pulsed and noise-like signals used in commercial and military radar, electronic warfare (EW), wireless communications (e.g., LTE, LTE-A, and 5G), and consumer electronics (WLAN), as well as education and research applications.
-
product
RF Chamber
HDRF-CHM-SERIES
*RF Chamber Designed and Developed for WLAN , Wireless device testing.*Ideal RF Enclosure for 802.11a, b, g, n, ac Device Testing*Ideal RF Shield for Bluetooth, RFID, 3G Device testing
-
product
Bluetooth and WLAN Testers
Bluetooth and WLAN Testers provide a full range of test capabilities for all R&D, manufacturing, and field applications.
-
product
PXIe-5665, Up to 14 GHz PXI Vector Signal Analyzer
781426-03
Up to 14 GHz PXI Vector Signal Analyzer - The PXIe‑5665 is a modular, three‑stage superheterodyne analyzer that you can use as either a spectrum analyzer or vector signal analyzer. It supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. In addition, you can use the PXIe‑5665 with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5665 can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5665 provides a low-cost solution to high-performance RF measurements.
-
product
PXIe-5665, Up to 14 GHz PXI Vector Signal Analyzer
781774-01
Up to 14 GHz PXI Vector Signal Analyzer - The PXIe‑5665 is a modular, three‑stage superheterodyne analyzer that you can use as either a spectrum analyzer or vector signal analyzer. It supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. In addition, you can use the PXIe‑5665 with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5665 can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5665 provides a low-cost solution to high-performance RF measurements.
-
product
Wireless Device Server
Your product description goes here.Advantech's wireless device server bring RS-232/422/485 to your WLAN or LAN, allowing devices with a serial ports to be connected and shared on WLAN.
-
product
Medium-size Reverberation Chamber
E-Series
The E medium-size multicavity Reverberation Chamber Series represents that state-of-the-art in reverberation chamber technology. The E-Series can make single measurements, batch tests, protocols or campaign tests for different frequency bands, different technologies and different channel models, running overnight without human intervention. Embedded frequency-, mode-, source- and platform-stirring in a double-shielded set of cavities allow Passive MIMO (Efficiency, Correlation, Diversity Gain, MIMO Capacity and others), Active MIMO OTA (TRP, TIS, TPUT, MTS, CQI, M2TxDT, RSRP, MCL and others) and Time-Domain MIMO (DL/UL TCP/UDP TPUT, RMS DS, STD, PL, CBW, Mute%, eNodeB, VDT-OTA) measurements up to 8x8 and 8DLCC to be performed for antennas and devices up to 50cm and 50kg ranging from 2G to 4G, covering all available cellular and wireless technologies to date, including wearables devices, sound acoustic mute, WLAN and W-IoT testing. There is no RC in the market more advanced than the E-Series.
-
product
Vector Signal Generator
SMBV100B
The state-of-the-art R&S®SMBV100B vector signal generator sets standards for its class. Ultra high output power, fully calibrated wideband signal generation and intuitive touchscreen operation make the R&S®SMBV100B ideal for all kinds of applications.Always in line with the latest major digital communications standards, such as 5G NR, LTE and WLAN, the SMBV100B is the preferred test solution for receiver and component characterization.The R&S®SMBV100B has many GNSS options that transform the instrument into a reliable, full-featured GNSS simulator. Advanced simulation capabilities can run realistic and complex yet repeatable GNSS scenarios under controlled conditions.
-
product
802.11a,b,g RF Shielded Test Enclosure
JRE 0814-A
Testing tall devices? The 0814-A stands up to any test up to 18 GHz! Featuring a wide swing open door with durable latch handle, this enclosure is ideal for testing IEEE 802.11 a,b,g devices such as; WLAN, VoIP, access points and other RF devices.
-
product
SAR Testing
RF transmitters used in close proximity to the human body must be evaluated against human Exposure standards which set basic restrictions for the Specific Absorption Rate (SAR) of RF energy by any part of the human body. This may include two-way radios, cellular phones, smartphones, spread spectrum, Bluetooth devices, wireless EFTPOS terminals and WLAN devices used in PDA/notebook/laptop/tablet computers. In Australia and Europe, virtually all devices exceeding the power threshold of 20mW (13dBm) and used in close proximity to the human body must comply with SAR requirements. There is no such blanket exemption in the USA and Canada where each product must be assessed against frequency/power level criteria.
-
product
SDIO Wi-Fi Module
SX-SDMAC
This Wi-Fi SDIO module is a low-power, single-stream solution with 802.11a/b/g/n/ac support based on the QCA9377 System-on-Chip from Qualcomm Atheros. This module supports Wave 2 MU-MIMO (Client), which increases the overall WLAN system performance by 3X compared to 11n. The module’s small form factor, rich features, and low power make it perfect for portable devices.
-
product
Pneumatic Type
Concentric Technology Solutions, Inc.
The Pneumatic Operation series of shield boxes provides superior performance for efficient RF isolation test environment for testing mobile, WLAN and other small RF devices. Its pneumatic controls to open and close the lid can be controlled manually or with a remote control for semi-automatic operation.
-
product
802.11a,b,g Dual RF Shielded Test Enclosure
JRE 0814-2R-A
Containing all the capability of the larger JRE enclosures, the rack mounted 0814-2R-A is ideal for testing IEEE 802.11 a,b,g devices such as; WLAN, VoIP, access points and other RF devices. Two independent 0814 series enclosures are mounted in one 19 inch rack. Two shielded vents provide excellent cooling and optional fan(s) are available for those hot products. Tough 'honeycomb' vents maintain shielding effectiveness throughout the frequency range. Featuring rugged welded aluminum construction, you can be assured of its tight RF shielding effectiveness.
-
product
PXIe-5663E, 6.6 GHz PXI Vector Signal Analyzer
781260-02
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
product
PXIe-5663E, 6.6 GHz PXI Vector Signal Analyzer
781259-02
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
product
Data logger and Monitoring
Testo offers a wide range of data loggers for long-term recording of measurement data, e.g. for climate or temperature monitoring. Data monitoring systems are recommended for integrated measurement data monitoring. The testo Saveris system offers tamper-proof data recording and WLAN technology that provides access to your measurement data anywhere and at any time on PC, smartphone, or tablet.
-
product
Serial/Ethernet to Wi-Fi Module
SX-590
The SX-590 is Silex’s latest fifth generation high-performance Serial/Ethernet to Wi-Fi module that provides connectivity for low-power portable devices to 802.11 wireless local area networks (WLANS).
-
product
Doides
Skyworks diode product offering includes PIN, limiter, Schottky, and varactor diodes for a wide variety of microwave applications including WLAN, infrastructure, handset, Satcom, automotive, military, aerospace and defense, test & measurement, metering, medical and RDID.
-
product
Propsim Channel Emulation Solutions
Propsim Channel Emulation Solutions are versatile and easy-to-use in a wide range of applications including MIMO, Beamforming, WLAN, Aerospace, MANET and MIMO OTA testing.
-
product
Communications Manufacturing Test Set
CMW100
The R&S®CMW100 communications manufacturing test set is based on the R&S®CMW platform. The flexible RF interface permits simultaneous testing of up to eight devices. The R&S®CMW100 remote control and measurement concepts are compatible with the R&S®CMW500. The R&S®CMW100 is optimized for cost-effective calibration and verification of wireless devices in non-signaling mode (analyzer/generator). The tester provides a new eco-friendly hardware concept, featuring extremely low energy consumption and a very compact size, making it ideal for use in fully automated robotic production lines. It supports LTE, 5G NR, WLAN, Bluetooth® and IoT technologies, making it ready for today and tomorrow.
-
product
Wireless LAN Module
SX-SDMAC2
The SX-SDMAC2 is a dual band IEEE802.11 a/b/g/n/ac WLAN and Bluetooth 5.0 BR/EDR/LE (Class1) module based on Qualcomm QCA9379-3 chipset. It supports 2x2 antenna configuration for applications that require higher performance. Silex has separated the Bluetooth antenna from the Wi-Fi by creating a third antenna port, allowing concurrent operation of Wi-Fi and Bluetooth further optimizing the Wi-Fi and Bluetooth performance.
-
product
Wireless Connectivity and IoT Test System
IQxel-M4W
Suitable for the lab or manufacturing environment, the IQxel-M4W 6G is ideal for RF testing of wireless connectivity and IoT products. The platform’s flexible software supports the most prevalent wireless connectivity standards: WLAN 802.11ax (Wi-Fi 6) and legacy (802.11a/b/g/n/ac), Bluetooth® Classic and Low Energy (Bluetooth® LE) as well as Zigbee/Thread, Z-Wave, LPWAN technologies (Sigfox, LoRa) and cellular IoT technologies (NB-IoT, LTE-M, 5G) as well as navigational technologies.
-
product
OTA Power Measurement Solution
NRPM
The R&S®NRPM is a fully calibrated and individual scalable OTA power measurement solution for benchtop application or in anechoic chambers. Covering a frequency range from 18 GHz to 90 GHz it is perfect for Over-the-Air (OTA) beamforming verification in 5G, WLAN IEEE 802.11ad and IEEE 802.11ay and the calibration of the transmit antenna output power.
