Filter Results By:
Products
Applications
Manufacturers
Volt Meters
Measure differences in voltage.
-
product
Video Volt Meter
VVM
This hand-held, battery-powered Video Volt Meter measures sync, white and composite video with digital accuracy in volts peak-to-peak and I.R.E. units.
-
product
Carbon Pile Load Tester 500 AMP
6034
• Carbon pile tester handles all 6/12 volt batteries• Two large 4.5″ analog meters display amps and volts• DC test leads are 2.5′ 4 AWG cable• Unit comes with manual adjust knob• Buzzer sounds after load is engaged for 15 seconds• Imported
-
product
500 AMP Carbon Pile Load Tester
710
The #710 will perform variable load testing on 12 volt batteries rated as high as 1000 Cold Cranking Amps. Use this battery tester to simulate actual cranking loads. Also tests alternator charging voltage and relative starter current draw. The #710 features large dual meters to display the battery voltage and load current simultaneously, during the test.
-
product
Digital AC milli Volt meter
PGP Electronics Private Limited
PGP Electronics Digital AC Mill voltmeter is a very versatile and general purpose equipment for the measurement of audio frequencies. It is useful in measuring low amplitude signals over a wide band of frequencies with precision. Its has a wide band width and sensitivity is 10uV. This instrument is useful for all amplifiers/ audio system manufacturers, college laboratories to measure input/output of any amplifier as well as frequency response of that amplifiers. .
-
product
Field Strength Meter
FIM-72A UHF
The Model FIM-72A is a portable, laboratory quality Field Strength Meter designed for rigorous field applications. Combining a calibrated half-wave dipole antenna and a highly accurate tuned voltmeter with a range of 140 dB, the FIM-72A is suitable for practically all types of RF emission measurements in the 450 MHz to 960 MHz spectrum. The operator can switch select wide or narrow bandwidth, peak or average value of TV or pulse modulated signals, AM or FM demodulation, and meter dynamic range of either 20 dB or 60 dB. A dc analog voltage, proportional to meter indication, is provided for driving a chart recorder or similar device. A leveled output from the calibrating generator is available for measuring cable insertion loss, filter response, amplifier gain, VSWR, and other signal ratio measurements. The 4-1/2 inch, taut band, mirrored scale meter is calibrated in volts and dB for precise measurements in field or laboratory environments.
-
product
6/8/12 Volt 0-1000 Amp Heavy-Duty Variable Carbon Pile Load Tester
7136R
• High-volume testing and fleet use• Tests 6/12 Volt batteries• 1000 Amp load; tests batteries up to 2000 cold cranking amps• Built in LCD Digital Voltmeter and LCD Digital Amp Meter• Cools with high RPM fan for continuous battery testing• High resolution carbon pile assembly for smoother operation and longer life• Optional Model 6038C for added mobility with convenient heavy-duty cart with wheels• RoHS and CE Compliant• Made in USA of US and Global Components
-
product
Single Phase Socket Tester
K-280
TESCO Knopp’s K-280 Single Phase Socket Tester is designed to detect short circuits, backfeed and wiring errors in a 120/240 volt, 3-wire, single phase self-contained meter socket.
-
product
Signal Level Meter
HT828B
Hangzhou Softel Optic Co., Ltd.
The signal level meter, SE828C is able to measure EQ, C/N, V/A and trunk volt in the CATV analog system, the number keys is designed to direct input frequency so that work would be easier. It can measure 2 channels at the same time.
-
product
Battery Load Tester
BT-100
Schumacher Electric Corporation
FOR EVERYDAY DIY USEEasy to operateTest load, battery condition, starter motor draw and complete charging system diagnosis.Works on 6 and 12 volt batteries50 amp load test for 6 volt batteries100 amp load test for 12 volt batteries Tests 6 and 12 volt batteries ─ up to 1000 CCATop-mounted rocker switch for easier operationSuper-grip, heavy-duty color-coded battery clampsEasy-to-read meter ─ accurate and shock resistantBaked enamel, steel case ─ ventilated to keep coolRubber insulated carrying handle ─ for comfort and safety
-
product
Floor Resistance Test Kit
PMK-152
The PMK-152 Floor Resistance Test Kit contains the instruments you need to take resistance measurements.The PMK-152 includes Prostat's PRS-812 Resistance Meter with 5 pound conductive rubber electrodes. You can take measurements at 10 and 100 volts with accuracy within ±5%.
-
product
Satellite Signal Level Meter
Super Buddy 29
The Super Buddy 29 satellite meter has all of the great features of the standard Super Buddy satellite meter plus an internal combo 21 volt / 29 volt module to power the new DIRECTV SWM LNBs and the WildBlue / Telesat / Xplornet TRIAs! Be "sure of your bird" with the positive ID feature or use the automatic scan to identify the unknown satellite.
-
product
LED Volt Meter
Global Digital Instruments, LLC
SenDEC LED Volt meters were developed to fill the need for a modern, high quality, super rugged DC Volt meter at an economical price.?? These solid state meters display the equipment's DC voltage level using a 10 segment LED bar graph display.?? Each bar represents 1 volt and corresponds to the printed voltage on the meter face.?? Models may be ordered for 12, 24, 36, or 48 volt DC systems.??
-
product
Digital DC Micro Volt meter
PGP Electronics Private Limited
PGP Electronics Digital DC Micro Voltmeter is a precision measuring tool for the measurement of low DC Voltages. This unit can measure low DC voltages, typically in the order of Micro Volts. This instrument is designed to with stand rugged operation.
-
product
Automated Potentiometer Systems
Measurements International Ltd.
Intrinsically Accurate Self-Calibrating Ratio Divider, Best Accuracy < 0.05 ppm, Built-in 20-Channel Scanner, Arbitrary Voltages from 1 mV to 1200 V, Bipolar Voltage Measurements, Calibration of Fluke 5700A/5720A, Calibration of 3458A and 8508A, Calibration of Voltage Ratio Dividers (F752A, MI 1340A, G7520), Linearity Calibration of Digital Volt Meters (DVM), Traceability to 10 V Zener Reference.
-
product
DC - 400 MHz PC-Based Timer Interval Analyzer
GuideTech’s GT658PCI is an ultra-fast, high resolution, DC – 400 MHz Time Interval Analyzer (TIA), ideal for most PC-based lab bench (timing) test applications. What makes the GT 658 superior to traditional counters is analogous to the difference between volt meters & digital scopes. While both measure voltage, the scope provides much more information about the dynamics of the signal. This is because our patented TIA substantially increases measurement speed, and the measurements are displayed as afunction of time. All of these features, along with the benefit of ‘continuous time correlation to a common reference between all measurement time stamps,’ enable our TIAs to make measurements that weren’t previously possible with traditional counters.
-
product
Pro Model Automotive Meter W/PC Interface
595
The #595 is a premier automotive diagnostic tool. It is equipped with the latest testing capabilities, including Milliseconds Pulse Width, for measuring the on-time of fuel injectors. The #595 features a huge LCD display w/bargraph for easy viewing. This meter can even be interfaced to your PC or notebook computer for enhanced diagnostics and data presentation. The software and computer interface cable are included free! The #595 includes two sets of test leads, RPM pick-up, temperature probe, software CD, interface cable, protective holster, 9 volt battery, instructions manual and hard storage case. Inductive RPM pick-up features a five position, adjustable sensitivity switch.
-
product
Professional Floor Certification Kit
PFC-252
The PFC-252 includes Prostat's PRS-812 Resistance System Set with modified 5 pound conductive rubber electrodes and Prostat’s Cable Spacers for exact measurements. The PRS-812 wide range resistance system can take measurements at 10 and 100 volts with accuracy within ±5%. Also included is the PFK-100 Field Meter Set. The PFK-100 set includes Prostat's unique PFM-711A dual range field meter, CPM-720A charged plate monitor assembly and PCS-730 ±1 kv charging source. With this instrument set you can measure electrostatic fields, analyze ionizer performance and assess the voltage generation of materials, equipment and personnel.
-
product
Digital Multimeter
MM-2
Our compact, low cost Model MM-2 Digital Multimeter with True RMS is ideal for general electrical testing and troubleshooting. This full function multimeter measures DC voltage to 1000 V and AC voltage to 750 V, DC and AC current to 10 A and resistance to 400 Ohms. In addition to volts, amps and ohms, this meter includes audible continuity, diode, LED and transistor hFE tests. The rotary switch allows you to select from any of the functions quickly and easily.
-
product
Super Energizer 5
SE-5
Parker McCrory Manufacturing Co.
A powerful model designed for today`s large pastures. Ideal for single or multi-wired high tensile fences. The Super Energizer 5 does everything a fence controller should do – it just does it better!!! Super Energizer 5 is equipped with a built-in DIGITAL performance meter which tells you the exact condition of fence. Shocks through wet weeds and brush. Over 8,000 volts of holding power with 500 OHM load. New color coded fence and ground terminals. Red to the fence and Black to ground. The Super Energizer 5 controls both predators and livestock, including sheep and goats. Fuse protection with built-in lightning arresters. Full 3 year warranty covers damage caused by lightning.
-
product
RF Volt Meters
The latest addition to Boonton’s popular 9200 series of RF voltmeters. It combines accuracy, smart probes, and operator features that have never before been available in its price range.
-
product
Ionization Test Set
PFK-105
- Ionization Test Kit for Measuring Offset Voltage and Discharge Times- Includes a Field Meter, Charge Plate Monitor, ±1000 Volt Charger and Decay Timer- Balance Ionizers per ANSI/ESD SP3.3 Periodic Verification- Measure Ionizer Decay time as per ANSI/ESD S3.1 and ANSI/ESD SP3.3.- Measure Body Voltage Generation and Decay- Evaluate Ionizers and Packaging Materials- Includes a fixture to hold the PFM-711B, CPM-720B and PDT-740B as one- Molded Carrying Case with Foam Insert Included
-
product
PC-Based Time Interval Analyzer
GT658PCI
GuideTech’s GT658PCI is an ultra-fast, high resolution, DC – 400 MHz Time Interval Analyzer (TIA), ideal for most PC-based lab bench (timing) test applications. What makes the GT 658 superior to traditional counters is analogous to the difference between volt meters & digital scopes. While both measure voltage, the scope provides much more information about the dynamics of the signal. This is because our patented TIA substantially increases measurement speed, and the measurements are displayed as afunction of time. All of these features, along with the benefit of ‘continuous time correlation to a common reference between all measurement time stamps,’ enable our TIAs to make measurements that weren’t previously possible with traditional counters.
-
product
6/12 Volt Digital Volt Meter
12-1011
• 6/12 Volt Digital Volt Meter• Light weight accurate 6/12 Volt Digital Volt Meter• Check charging system and battery voltages• Reverse hook-up protection• Four digit display• OCV state of charge percentage for both batteries AGM and Flooded
-
product
True RMS Multimeter w/ Temperature and Capacitance
DM393
UEi Test & Measurement Instruments
The DM393 is one of our safest Industrial Duty meters ever made. All inputs, ranges and functions protected to CATIII 1000 Volts. Perfect for HVAC and electrical technicians whose applications require higher accuracy measurements and True RMS precision. Built-in temperature means one less instrument to bring to the job. The DM393 has convenient access to battery and fuses without breaking calibration seals
-
product
Polyphase Socket Tester
K-281
Knopp’s K-281 Polyphase Socket Tester is designed to detect backfeed conditions, grounds, short circuits and wiring errors in either a 120/240, 120/208 or 277/480 volt meter socket. It is equipped with high intensity Power Lights and Fault Lights to show whether or not the meter is safe to set. The Polyphase Socket Tester also comes with a heavy duty handle for quick and easy installation.
-
product
Digital Sensors
PMA-Series
Solar Light’s NIST-Traceable PMA-Series Digital Sensors represent the pinnacle of accuracy, durability, and selection on the market today. Our sensors measure discrete bands of the electromagnetic spectrum from the UVA, UVB, UVA+B, UVC, Visible Light, and Infrared regions. Both narrow and broad bands are available to fit any application, including germicidal requirements, environmental probes, and sensors for biologically weighted spectra (such as the erythema and CIE action spectra.) Over 135 different sensors are available in a variety of packages to fit any environment, from indoor clean rooms to harsh locations outdoors to 100 meters under water. Please note that Solar Light offers both Digital Sensors and Analog Sensors in the PMA-Series lineup. Select these Digital Sensors if you prefer to plug into our PMA-Series Radiometers to read the output of the sensor on the meter’s display. Digital models are typically used as discrete sensors that are portable and located to provide short term information. (By contrast, please select Analog Sensors if you don’t need a digital display output of the reading, if you will be connecting to your own datalogger, or if you plan to use a voltage source to provide excitation voltage to the sensor and a digital volt or amp meter to read and convert the results. Analog Sensors are typically used as process sensors that are permanently installed to provide ongoing information.)
-
product
Battery Impedance Meter
Operation is fast and simple. Just press the spring-loaded probes onto the two poles of the battery. After 1.5 seconds, the unit beeps (indicating good contact) and displays the battery voltage and either the number of siemens or milliohms, depending on the knob setting. The display continues to show these numbers after the probes are removed; it resets only when the probes are pressed onto the next battery. The impedance and voltage of any battery between 1.2 and 60 volts can be read. Because of the wide range of voltages, even single low-voltage cells, such as NiMH, can be measured. The manufacturers of some batteries specify impedance in milliohms while other specify in siemens (one divided by the resistance in ohms). This meter will display both types of impedance for any given battery. Accuracy is +/- 2% of the value.
-
product
CAT IV 600 A TRMS Navigator Clamp Meter
ACD-51NAV
This versatile clamp-on power meter offers a full range of diagnostics, including those that HVAC technicians need most—volts, amps, resistance, capacitance, DC microamps, in-rush current and temperature.
-
product
Analog Panel Meter
Hoyt Electrical Instrument Works Inc.
Hoyt supplies a complete line of panel meters for several vertical markets (Switchboard, Audio, Power, Marine, and Power Generation). The meter movements can be pivot & jewel or taut band. So whether you are looking for AC/DC amps, volts, frequency, elapsed time, watts, vars, power factor, or any other measurement parameter we have the meter.
-
product
DC Meters/Rail Meters:
Digital DC Resistive Voltmeter has a single range of 0 – 2kV. The unit consists of a meter probe, second probe, and connector cable. This unit is designed to measure DC voltage between the negative return rail and overhead positive cantenary conductor used on transit systems. The five position selector switch located on the face, controls OFF, ON, and Test. The OFF positions are for storage and transit. The ON position is for measurements from 0 to 1999 volts with one-volt resolution. The T position tests basic meter functions and the digital display.
