Filter Results By:
Products
Applications
Manufacturers
-
product
Vacuum, Module, Receiver, 90 Series, 2 Port Positions
510104260
Primary mating module 510108242. (May mate with other ITA modules, as well.)
-
product
Environmental Testing
Environmental testing typically involves hot or cold temperatures, humidity, altitude (vacuum) or thermal shock. This testing can even be combined with other test methods such as vibration or shock.
-
product
Wafer Bonder
AML
Wafer bonding has found many applications in the field of MST, MEMS and micro engineering. These include the fabrication of pressure sensors, accelerometers, micro-pumps and other fluid handling devices. The process is also used for first-order packaging of silicon microstructures to isolate package-induced stresses. The OAI AML Wafer Bonder facilitates both the alignment and bonding to be performed in-situ, in a high vacuum chamber. For anodic bonding the wafers are loaded cold and heated in the process chamber. For high accuracy alignment the wafers are aligned and brought into contact only after the process temperature has been reached, thus avoiding differential thermal expansion effects which can compromise alignment. The AML Wafer Bonder is excellent for anodic bonding, silicon direct and thermal compression bonding applications. These features enable the bonder to be used with virtually any processing tool.
-
product
Differential Pressure Transmitter
608
The Dwyer Series 608 Differential Pressure Transmitters convert positive, negative (vacuum), or differential pressures of clean, dry air or other non-conductive, non-corrosive gases into a standard two wire, 4-20 mA output signal
-
product
Automated Breakthrough Analyzer
ABR
The ABR is a dedicated breakthrough analyzer with fully programmable operation including control of total pressure, flow rate, composition and temperature. Samples are loaded into interchangeable reactor beds and dried in-situ with purge gas or vacuum at elevated temperature. Reactive gas mixtures are then flowed through the bed, and the downstream composition determined in real-time with an integrated mass spectrometer.
-
product
Motors and Resolvers
We design, manufacture and test highly reliable motion control devices for extreme environments that range from vacuum and the extreme cold of outer space to high pressure and temperature applications many miles under the earth's surface.
-
product
Thin Films, Plasma and Surface Engineering
A residual gas analyser for vacuum process analysis. Measures the vacuum process gas composition, contamination and leak detection.
-
product
1.533 Μm Frequency-Locked Laser
Thorlabs' LLD1530 Frequency-Locked Laser is a narrow linewidth, DFB-laser-diode-based, turnkey system with a vacuum emission wavelength of 1532.8323 nm and a high SMSR of at least 35 dB. The laser frequency is actively stabilized to a National Institute of Standards and Technology (NIST)-traceable molecular transition of acetylene and has an absolute accuracy at start-up that is better than ±25 MHz. The emission frequency immediately after start-up is then maintained with a ±25 MHz stability, providing an overall frequency accuracy of ±50 MHz. The LLD1530 is an accurate frequency reference designed to provide low-noise laser emission with excellent frequency stability, accuracy, and precision immediately at start-up. This source is ideal for use in demanding FTIR instrumentation, instrument calibration, gas sensing, and coherent telecommunications applications.
-
product
Vacuum Tester
QCT-2A
Changzhou Chanlon Electronic Technology Co., Ltd.
This machine is applied to vacuum cleaner type motor. Its LCD shows all technical data which obtained by industrial control computer, which check and verify the quality of testing stator.
-
product
Mass Spectrometers
Our wide range of powerful, versatile, and proven mass spectrometry-based solutions deliver a new level of understanding and control in vacuum and gas-related applications to customers.
-
product
Spinstand Automation for Media Testing
V2002
The spinstand V2002 with the media-testing automation loads and unloads the cap of the vacuum chuck1 and moves the disk stabilizer shroud on and off media without operator’s intervention. As a result, less time is required for a media replacement, so the same number of disks can be tested faster.
-
product
Vacuum Modules
VPC offers a wide array of modules with a variety of connection options that are configurable for virtually any interconnect requirement.
-
product
Metal Detection Pipeline System for Vacuum Fillers
HDS
Metal detection systems for sausage manufacture and inspection of high viscosity liquids. The maximum capacity to detect all metal contaminants combined with stable on-line performance. Full stainless steel construction and sealing standards up to IP69K make HDS pipeline detectors suitable for the harshest meat processing environments.
-
product
Vacuum Interrupter Pressure Integrity Test Set
Low Drift Current is measured by applying magnetic field.
-
product
Vacuum Handling Systems
RECIF Technologies history started in 1982 offering its first wafer handling solution: Vacuum handling Systems.Based on this historical technical mastery, Recif Technologies provides today a full range of single wafer manual vacuum handling solutions adapted to our customers’ and current Semiconductor industry’s’ requirements.
-
product
Microtomography
Have you ever seen images from a medical CT-scanner? Now, the same technique can be applied to your micro samples! SkyScan systems from Bruker microCT allow you to cut virtual sections or even fly through samples non-destructively. No preparation, coating or vacuum treatment is needed. Bruker microCT micro-tomography is available in a range of easy-to-use desktop instruments, which generate 3D images of your sample’s morphology and internal microstructure with resolution down to the sub-micron level. Software for visualization and analysis in 3D is included with all SkyScan systems.
-
-
product
HV High Performance Circuit Breaker Analyzer
CBV-32
We conceived the CBV-32 to provide the best range of testing for electrical facilities such as circuit breakers (using gaz, oil, air, vacuum…) or synchronous condensers all the way up to 800kV and more. It combines Timing, Motion Dynamic Resistance Measurements, and Vibration, all in a single test.
-
product
Ultra Pure Vacuum Switch (longbody, NEMA 4)
W117LV
The W117LV NEMA IV Rated Ultra Pure Stainless Steel Vacuum Switches have all welded stainless steel interiors which are Helium leak checked to pass 4 x 10-9 Std cc/sec. These are the weather-proof, liquid-resistant version of the W117V suitable for outside applications or in areas of condensing humidity.
-
product
D1 Series
With VPC's most compact design, the D1 is compatible with a variety of hybrid I/O modules that include: power, coax, signal, vacuum, pneumatic, and high speed digital. Despite its compact size, the D1 can engage up to 160 signal contacts simultaneously.
-
product
Measuring Fork Sensors
Leuze electronic GmbH + Co. KG
With the sensors, an infrared light-band illuminates a CCD line. A passing object can thereby be measured by its occlusion. The resolution of 14 µm and the high reproducibility enable the reliable measurement of very fine yarns and wires. The variety of implementable measurement functions enables the position detection of transparent edges, the determination of the thinnest or thickest wire and much more. The vacuum resistance of the devices also enables use in carbon fiber production.
-
product
Altitude & Space Simulation Test Chambers
Weiss Technik’s vast experience with altitude, thermal vacuum, low temperature and space simulation test chambers can provide you with the right solution. We offer both pre-engineered and custom altitude chambers for ultra-low cooling, extended mbar, and extended temperature ranges that will meet your testing exact requirement.
-
product
Vacuum Leak Test Systems
Vacuum leak testing is the principal leak test method for testing parts that could have leakage from an external source into their housings and casings. Parts like underwater sensors or housings, outdoor electrical housings, sealed components, and components associated with vacuum sources are all prime candidates for vacuum leak testing. Operation of instruments that supply vacuum to test parts instead of pressure works in a similar, yet essentially opposite, manner as pressure decay testing.
-
product
Low-Noise Cameras with Fiberoptic Design with Multiple Phosphor Screen Options for the Detection of X-Rays
PIXIS-XF
Teledyne Princeton Instruments
PIXIS-XF low-noise cameras have a unique fiberoptic design with multiple phosphor screen options for the direct detection of x-rays. With an exclusive mechanical design, where the fiberoptic faceplate extends outside the vacuum, the PIXIS-XF offers flexibility for optimizing performance at specific medium-energy x-rays.
-
product
ATE Test Probes
For contacting loaded PCBs in automatic test equipment (ATE) with vacuum, pneumatic or mechanically operated fixtures. Available in 2.54mm, 1.91mm & 1.27mm test centre spacings.
-
product
Gaussmeter
450
The Model 450 is a high-resolution, laboratory gaussmeter, capable of measuring magnetic fields from 0.001 Gauss to 300k Gauss (measurement range is dependent on probe used). This unit is designed for demanding applications, such as material analysis and field mapping, where low-noise, high-resolution magnetic measurements are necessary. Measurements of AC and DC magnetic fields are shown in Gauss or Tesla on the two-line vacuum fluorescent display. The Model 450 features RS232C and IEEE-488 ports, allowing the instrument to be controlled via a remote computer or automation equipment. A hall-effect gaussmeter probe is included with the Model 450, and may be selected from an extensive line of probe
-
product
Vacuum Test Fixtures
Series 63
The VT Series 63 vacuum test kits provide both an affordable and versatile solution for printed circuit board testing requiring vacuum actuation and a Genrad 2270/71 interface. The VT Series 63 kits, available in Single and Dual Well models, incorporate a robust design which includes a variety of chassis sizes and depths for additional hardware and components used in Functional Test. Tooling holes on both the top diaphragm plate and probe plate for accurate drill datum. The interface will accommodate up to 11 I/O blocks with a single vacuum port.
-
product
10 MHz To 54 GHz LAN Thermal Vacuum Compliance Power Sensor
L2066XT
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
-
product
Vacuum Discharge Test Equipment
DAC-VD-1
DAC-VD-1 can locate defective points such as scars or pinholes on stator coils and wires easily.By applying voltage in a vacuum chamber, the electric arcing from a defective part can be discoveredvisually in a short time. DAC-VD-1 can be used widely in variety of applications from product developments to outgoing inspections.
-
product
Can Inspection
Whether they are 14oz cans, 28oz cans, 12oz bottles, or some other size or format – they typically all look fine, as they fly by on your production line or sit on pallets ready to go out to customers. The challenge is, most companies have some kind of sealing issue at some point. Tops go on crooked, lids don’t seal, vacuums don’t set right – and it’s nearly impossible to tell by physical or visual inspection.
