Filter Results By:
Products
Applications
Manufacturers
VMEbus
VERSAmodule Eurocard bus
-
product
M-Module Carrier for VMEbus (6U)
i4000
The i4000 is a 6U form factor M-module carrier for the VMEbus and forms the basis of a flexible I/O system. It offers the user a means of integrating a mix of M-modules in a VMEbus system. Four M-module mounting sockets are provided by this carrier.The interrupt controller on the i4000 has an interrupt vector register for each M-module interface.
-
product
Backplane
VME64/VME64x
VECTOR Electronics and Technology, Inc.
Vector offers a comprehensive range of VMEbus backplanes from 2 to 21 slots. VME J1/J2 and VME64x J1/J2/P0 backplanes per ANSI/VITA 1.1-1997. Monolithic 6U high VME64 and VME64x backplanes are fully RoHS compliant and perform to ANSI/VITA 1.7-2003 (R2009) increased current level for VME (96 pin) and VME64x (160 pin) DIN/IEC connectors.
-
product
Dual Channel Digital Receiver
MS 1740
Dual Channel Digital Receiver is a complete high−frequency dual−channel A/D converter capable of sampling rates up to 210 MHz. It accepts two front panel analog inputs and delivers digital output samples over four FPDP (Front Panel Data Port) connectors utilizing FPDP standards. The Dual Channel Digital Receiver features two 12−bit Analog Devices AD9430 A/D Converters, and two user−configurable Xilinx® Virtex−IV Series FPGAs. It also features a VME A64/D64 slave interface for setting up operating modes and selectable A/D range, and optionally provides 32−bit access from the VMEbus to the FPGAs. It is an ideal system as a high−speed data acquisition front end for real time recording and digital signal processing systems.
-
product
VMEbus Repeater Link
VME-REPEAT-A-L
The VME-REPEAT-A-L is a two-board set which allows VMEbus slave I/O boards residing in one VMEbus chassis to be controlled by a VMEbus master residing in another chassis. The VMEbus chassis in which VMEbus masters reside is referred to as a master chassis, while the VMEbus slave boards reside in a slave chassis.
-
product
VME Modules
VME is a high speed and high performance bus system with powerful interrupt management and multiprocessor capability. It was created by combining VERSA-bus electrical specifications (1979) with the Euro-card format resulting in the VME-bus Revision A - 1981 specification.
-
product
Digital Output Board
VME-2533
VME-2533 32-bit Differential Digital Output Board. VMEbus specification compatible double height form factor.
-
product
VME / VSB Module
ADM-42M
The AD42M Data Acquisition Module provides high performance 14-bit digitizing of analog signals for VMEbus applications. The AD42M accepts 4 differential analog inputs via front panel miniature SMC connectors. The AD42M utilizes a signal processor to acquire and store data samples. The AD42M is able to direct the data samples to local static RAM or VSB.
-
product
SCSI Fast/Wide Single-Ended VMEbus P2 Paddle Card
2699
Our SCSI Fast/Wide Single-Ended VMEbus P2 Paddle Card (2699) use a 68-pin SCSI Fast/Wide connector to bring out multiple ports. Transition panels and paddle cards are intended to adapt the 68-pin connector to more traditional connectors used in applications.
-
product
VMEbus board
IIB-429--VME-4C
The IIB-429-VME-4C provides 16 ARINC-429 compatible channels (8 receive and 8 transmit) at any rate between 12.5 and 100 kbps. Because the IIB-429-VME-4C is built upon a flexible platform, user function can be implemented almost without restriction, making this product flexible and user-friendly. This VMEbus board has a 6U form factor. This VME unit is also available in a 3U form factor, as IIB-429-VME.
-
product
High-Resolution VMEbus Laser Axis Board
10897D
The 10897D High-resolution VMEbus laser axis board provides excellent resolution of up to 0.3 nm with a high resolution interferometer. The data age uncertainty is dramatically reduced allowing extremely accurate measurement and control of moving systems. The very high data rates accommodate high-bandwidth and high-performance closed-loop applications. Configured with appropriate lasers and optics components, the 10897D supplies unsurpassed positioning accuracy for dynamic measurement.
-
product
VME 3U 129-130-30-31
Hartmann Electronic is an industry leader in the designing, manufacturing and production of backplane technology, including VME and VME64x. Over the evolution of its near 40 years of existence, VME-bus has become a worldwide standard and is still used in a wide variety of applications across many different markets.
-
product
Digital Input Board
VME-1129
VME-1129 128-bit high voltage digital input board with Built-in-Test and input filter. This product complies with the VMEbus specification (ANSI/IEEE STD 1014-1987, IEC 821 and 297), with the following mnemonics: A24:A16: D32/D16/D08 (EO): Slave:39/3D: 29/2D Form Factor: 6U
-
product
Stepper Motor Controller for VMEbus
VME321
The VME321 Intelligent Stepper Motor Controller with Amplifiers is an ideal solution for all applications where stepper motors must be controlled with a maximum of flexibility and a minimum of overhead. The local processor handles all high-level commands to provide maximum control for both straightforward as very complex applications.This VMEbus board has a 6U form and is also available as 3U VMEbus board.
-
product
VME-Bus Synchro - Resolver LVDT I/O Cards
VB Series
Computer Conversions Corporation
The "VB Series" product lines contains VME compatible synchro/resolver converters and absolute encoder systems. These particular cards are ideal for any rotary motion and related process, control, or simulator type application with any VME compatible system.
-
product
64 Channel ADC for VMEbus
VME392
The VME392 features 64 self-contained ADC channels with a resolution of either 12 or 16-bit (see ordering information). This product is ideally suited for mass acquisition with high accuracy for reasonable cost. The 64 channels are grouped into four sections of 16 channels each. Each section behaves completely independent from the other sections.
-
product
Serial Controller
PMC522/FP
The PMC522/FP provides a uniquely effective solution for integrating serial I/O requirements into a VMEbus or CompactPCI system. Implemented on a single PMC card, the PMC522/FP is fully compatible with the current generation of VMEbus and CPCI single board computers, as well as any special purpose processor that includes a PMC connector.
-
product
Digital Output
VME-2170A
The VME-2170A optically coupled digital output board consists of VMEbus compatibility logic,data control logic, four 8-bit output registers, and 32 optically isolated high-level outputs. The board is implemented as a double Eurocard form factor PC board, and provides all necessary address decoding and data transfer control logic to accept both 8- and 16-bit data transfers. Optical couplers isolate the 32 outputs from each other and from the VMEbus.
-
product
Single / Dual Power PC
DP-VME-0447
DP-VME-0447 is a Single/Dual Power PC7448/7447A SBC.This dual or single processor VME-bus computer to meet needs of high performance embedded applications. It addresses such markets as defence, aerospace and automation, where real-time control signal processing is required. Applications for this board include VME computers, signal processing units, airborne system controllers, and automation systems.
-
product
6U Form Factor PMC/PrPMC Carrier-VMEbus
i4400
The i4400 is a low-cost 6U form factor PMC / PrPMC carrier for the VMEbus and forms the basis of a flexible I/O system. It offers the user a means of integrating two single PMC modules or one double PMC module in a VMEbus system. The current version of the i4400 supports PMC modules and also supports Processor PMC modules on one PMC-site. The VME-to-PCI bridge is implemented in an FPGA for flexible VME-to-PCI mapping and to allow future updates and upgrades.
-
product
SCSI Fast/Wide Differential VMEbus P2 Paddle Card
1870
Our SCSI Fast/Wide Differential VMEbus P2 Paddle Card (1870) use a 68-pin SCSI Fast/Wide connector to bring out multiple ports. Transition panels and paddle cards are intended to adapt the 68-pin connector to more traditional connectors used in applications.
-
product
16-Channel VME Analog Output/Thermocouple Simulator Module
V470
The V470 is a 6U VME module that provides sixteen independent, isolated analog outputs that may be user-programmed to operate as voltage outputs or thermocouple simulators. Users may write temperature or voltage values at VMEbus speed, and the microprocessor will transparently do all necessary calculations and update the channel electronics.
-
product
VME / VME64x Chassis
Hartmann Electronic is an industry leader in the designing, manufacturing and production of backplane technology, including VME and VME64x. Over the evolution of its near 40 years of existence, VME-bus has become a worldwide standard and is still used in a wide variety of applications across many different markets.
-
product
Universal Timer/Counter for VMEbus
VME385
The VME385 Universal/Timer Controller VMEbus board is an ideal solution for automated test and measurement applications. The VME385 features eight timer/counter inputs, all inputs have an coaxial connector for the input range of +/- 10 V and high-voltage pins for the input range of +/- 300 V. The coupling of the inputs is either AC or DC. The VME385 provides 6 measurement functions: frequency, high-time, low-time, period, counter and phase measurements.
-
product
16 Channel ARINC-429 Controller for VMEbus
VME302
The VME302 provides sixteen ARINC-429 compatible channels (8x receive and 8x transmit) at any rate between 12.5 and 100kbps. Because the VME302 is built upon a flexible platform, the user interface is extremely versatile and user functions can be implemented almost without restriction, making this product flexible and user-friendly.
-
product
Expansion Card
PMC238
The PMC238 is a 6U form factor card that expands a single PMC site on a VMEbus processor board to two PMC sites and one PCMCIA/CardBus socket or to three PMC sites. Compatible with many VMEbus single board computers, it provides an extension of PCI and PCMCIA capacity within the VMEbus form factor. The PMC238 has the option for the PCMCIA/CardBus cards to be mounted outside the chassis using an 18-inch cable.
-
product
Interface
RMAC-VME
Designed for laboratory simulation and production test applications, the Modular Avionics Controller (RMAC) is an intelligent, high performance 6U VME product supporting ARINC protocols and other serial communications. As an evolutionary follow-on product to the successful VME-AIC product line, the RMAC-VME provides a single integrated interface to multiple avionics protocols on VMEbus platforms.
-
product
CANbus Controller for VMEbus
VME360
The VME360 CANbus controler is a 6U VMEbus board based on four SJA1000 CANbus controllers. Each SJA1000 provides an interface to the popular CANbus that supports both standard (11-bit) and extended (29-bit) identifier fields. Front panel LEDs provide diagnostical network information. The VME360 provides four CANbus interfaces. The CAN network is a serial communication protocol which efficiently supports distributed control with a high level of reliability.
-
product
Aerospace
AcQ can perform custom developments compliant with ED12/DO-178B and ED80/DO-254 in various design assurance levels (DALs) for safety critical applications, using the ED14/DO160 for the environmental requirements. AcQ also offers standard products for various open standards like VMEbus, CPCI, PCI and other bus standards for test applications and other applications like GPS, display, actuators, data logging and -storage.
-
product
VME 64x 6U 166
Hartmann Electronic is an industry leader in the designing, manufacturing and production of backplane technology, including VME and VME64x. Over the evolution of its near 40 years of existence, VME-bus has become a worldwide standard and is still used in a wide variety of applications across many different markets.
-
product
RTD Measurement for VMEbus
VME390
The VME390 features 24 two, three or four wire high-accuracy PT100 measurement channels. Each channel has programmable alarm limits on which an interrupt can be issued.
