Filter Results By:
Products
Applications
Manufacturers
Trace
-
product
Analog Oscilloscope
PS-200
*20MHz Dual Trace, Dual Trigger*Vert, Sensitivity From 1mv/DIV to 15V/DIV*Sweep Rate From 10ns/DIV to 2s/DIV*Hold-off, X-Y operation*CE, UL, CUL, TUV GS, IEC 1010, EN61010
-
product
Analog/Digital and Network Trace
At iSYSTEM, we realize that embedded systems development requires more than just the insights of the microcontroller/processor. Developers need a holistic view, covering external signals and serial bus messages, or even insights into more than one microcontroller/processor and/or traget system at once.
-
product
Liquid Calibration Unit
LCU
Versatile Trace Gas Calibration by Evaporation of Liquid Calibration Standards.
-
product
PCI Adapter for cPCI
PCI2cPCI
PCI2cPCI is an adapter familiy used to mount a cPCI device into a PCI connector. PCI2cPCI-32, PCI2cPCI-32-IO, and PCI2cPCI-64 are passive devices with impedance controlled traces interconnecting the Gold Fingers of the PCI edge connector to the press fit cPCI connector. All PCI signals are routed through including power, ground, PCI bus, secondary control signals.
-
product
In-Circuit Emulator
DS-251
# Real-Time and Transparent In-Circuit Emulator for 251s# Uses Intel and Atmel Licensed Bondout Technology# Standard 256K Emulation Memory# Real-Time Trace up to 128K Frames Deep, 128 Bits Wide# Complex Hardware Breakpoints# Supports Both Binary Mode and Source Mode# MS-Windows Debugger# High-Level Support for Popular C-Compilers# Full Support of Local and Global Variables# On-Line Assembler and Disassembler# Performance Analyzer
-
product
Trace Oxygen Analyzer
Model 3300TB
Teledyne Analytical Instruments
The 3300 series of low cost, microprocessor-based instrument are specially designed to satisfy industry’s need for a simple yet highly reliable process analyzer. These units offer excellent accuracy, ease of use, high reliability, low maintenance and a variety of standard features usually found on more expensive instruments.
-
product
Cable and Pipe Locator
PT-14
The locator PT-14 is used as an induction signal receiver in a cable tracing and fault location set for the following applications:• tracing – finding the route and determining the burial depth of underground cables and other hidden utilities;• fault location – pinpointing interphase and phase-to-sheath short circuits faults;• cable identification – identifying a correct cable from a bunch.
-
product
Wireless In-Circuit Test Fixtures
Higher density more complex circuit boards complicate testing requirements while smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in standard long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board or T-Board®. Circuit Check’s wireless fixture technologies reduce test program debug and maintenance times while easing the ECO process. Thus allowing for the higher level of test performance, the ability to probe smaller denser targets and achieve ultra-high node counts.
-
product
SF6 Gas Leak Detector
Weshine Electric Manufacturing Co., Ltd
1. SF6 quantitative leak detector is an ideal tool and method for sf6 gas trace leakage inspection. It has the advantages of fast, convenient, reliable, and low maintenance cost.2. Especially suitable for occasions with high frequency of use such as factory workshops.3. It is recommended to purchase model LF-200 products during after-sales or inspection, with a total product weight of 7.5Kg, equipped with a portable aluminum alloy crash box.
-
product
Cable Tracers
181 CB
Standard Electric Works Co., Ltd
● The Amplifier Probe is designed to identify and trace wires or cables within a group without damaging the insulation.● Works with any Tone Generator to identify wires.● Volume control for increased sensitivity and adjustable to suit work environment.● Recessed ON/OFF button prevents battery drain.● A phone jack is designed for headset or handset.
-
product
Explosion-Proof Oxygen Transmitter
OxyTrans-EX
The Edgetech Instruments Model OxyTrans is an easy to use, accurate and economical way to measure Oxygen at trace and % levels. A simple display and one point calibration allows for a quick start of the instrument.
-
product
Real-time S-Parameter And Power Measurement Uncertainty
S96015B
See real-time measurement uncertainty for S-parameters and power measurements with the measurement traces on one screen. Estimate uncertainty reliably and apply more realistic limit lines for pass/fail tests for better production yield rates
-
product
Multi-purpose Cable Tracer and Non-contact Voltage Detector
168 CB
Standard Electric Works Co., Ltd
● Four transmitter plug types - RJ-11 - RJ-45 - COAX - Alligator clips ● Two unique audible tones: - Fast alternating tone - Slow alternating tone ● Telephone line polarity check - Tip side - Ring side● Cable tracing ● Telephone line status check - Clear line - Busy line - Ringing line ● Continuity check.● Transmitter plug storage.● Easy to store different kinds of transmitter plugs (RJ-11, RJ-45, COAX, and alligator clips).● Easy to carry.● Flashlight function.
-
product
Frequency Selective Power Sensor
NRQ6
The R&S®NRQ6 is based on receiver technology and can perform band-limited power measurements down to -130 dBm. The R&S®NRQ6 combines high-precision with high-speed measurements beyond the limits of currently available power meters. In addition to conventional continuous average measurements, the R&S®NRQ6 has a trace display function and also performs ACLR measurements.
-
product
Sample Pretreatment For Optical Emission Spectrometry
Samples are taken from molten metal, thin sheet, semi-complete or complete products. When sampling molten metal with a ladle, small quantities of molten metal are poured into a casting mold. Unnecessary parts of the sample are removed using a grinder or a cutter. As particles from a grinder may contaminate the surface of the sample, a lathe or milling machine is used (not a grinder) to cut soft samples such as white metal. If trace elements are not being investigated, a grinder or belt sander can be used. However, to minimize contamination, the grinding wheel or belt should be changed for each sample. Samples excised from semi-complete or complete products must be at least 12 mm in diameter. Small rod-shaped samples can be analyzed using special equipment.
-
product
2100Vdc Screw Terminal Connector Board | Cable & Harness Tester
CB29H
CAMI Research Inc. (Acton, MA) announces another new board for its CableEye cable and harness testing systems. Populated with four 16-pole screw terminal blocks, the board addresses high voltage (HiPot) testing to 2100Vdc/1200Vac. Of particular interest to the harness testing market, the CB29H is also available as a transition board variant (CB29AH). The CB29H and CB29AH boards are high voltage versions of the CB29 with the high voltage traces running on inner layers to afford additional safety, and protection from contamination.
-
product
ALM Tool For End-to-End Traceability
HelixALM
Helix ALM is a modular suite of ALM tools. You can use this application lifecycle management suite to trace requirements, tests, and issues.
-
product
Zero-footprint Timing Analysis For Critical Software
RapiTimeZero
*Collect timing metrics from systems that produce branch traces* Identify code to optimize for worst-case behavior*Debug rare timing events*Simplify verification through integration with your CI tool*Analyze timing behavior of libraries without source code
-
product
Tone Generator with Cable Tracer
1RA470
Cable tracer is designed to trace wires without damaging the instalations. It has wolume control to increase sensitivity. Power supply is standard 9V battery.
-
product
Elemental Analyzers
Bruker manufactures instruments for elemental analysis from 100% down to the sub-ppb trace level. Easy-to-use solution packages help customers in process and quality control to meet industry norms and standards including ASTM, DIN, ISO and FDA. Highest analytical accuracy and precision enable academic research from lab to field.
-
product
JTAG Debug Probe for Cortex-M
J-Trace PRO
SEGGER Microcontroller GmbH & Co. KG
J-Trace PRO for Cortex-M is setting a new standard for trace probes. It enables continuous streaming trace via its Gigabit Ethernet interface, lifting the limitations by internal buffers and slow data transmission.J-Trace PRO can capture omplete traces over long periods - thereby enabling the recording of infrequent, hard-to-reproduce bugs. This is particularly helpful when the program flow 'runs off the rails' and stops in a fault state. It also supports extended trace features, such as code coverage (so engineers have visibility of which parts of the application code have been executed) and execution profiling (providing visibility as to which instructions have been executed and how often - so hotspots can be addressed and optimization opportunities identified).
-
product
Real-time S-Parameter And Power Measurement Uncertainty
S93015B
The S93015B provides real-time measurement uncertainty for S-parameters and power measurements with the measurement traces on the same screen. It enables the users to estimate more reliable uncertainty and apply more realistic limit lines for pass/fail tests for better production yield rates.
-
product
Trace Moisture Analysis System
Analyzing moisture, and how much of it, is critical to the performance of petroleum products, as well as infrastructure and product integrity. For example, moisture in petrochemical feedstock can cause pipelines and valves to freeze, as well as poison some catalysts. One popular method used to analyze for moisture is Karl Fischer Titration (KFT). KFT has a wide dynamic range but has difficulty in measuring relatively low amounts of moisture. In addition, there are the well-known problems of side reactions and known interferences.
-
product
Inductively Coupled Plasma
Inductively Coupled Plasma Techniques can be very powerful tools for detecting and analyzing trace and ultra-trace elements. Over the past years, ICP-MS has become the technique of choice in many analytical laboratories for providing the accurate and precise measurements needed for today’s demanding applications and for providing required lower limits of detection.
-
product
Cable ID & PoE Tester
PK-170 INNOTESTER PRO
INNOTESTER PRO combines the functions of a smart cable tester, network tester, port identifier and organizer with the capability to identify up to 100 cables run at a time, and 8 Test + ID remotes allows one person to test 8 cables run up to 600 meters. Tone mode, transmits 2 powerful tones for tracing inactive and active network cables on a Switch or HUB. More effectively tracing at patch panel, termination blocks or hidden within bundles.
-
product
Cable Tracers
179 CB
Standard Electric Works Co., Ltd
● The Amplifier Probe is designed to identify and trace wires or cables within a group without damaging the insulation.● Works with any Tone Generator to identify wires.● Volume control for increased sensitivity and adjustable to suit work environment.● Recessed ON/OFF button prevents battery drain.● A phone jack is designed for headset or handset.
-
product
Multiplex Temperature Meter (8 ,16, 64 Channel)
TP-1
Shenzhen Chuangxin Instruments Co., Ltd.
TP series of multiplex temperature meter is a kind of instrument which suits to real time monitor and trace multi-points temperature simultaneously. With the features of Simplified operation, high precision and reusable thermocouple, it is widely applied in electronic ballast, motor tools, lighting fixtures and household appliances. The application software records and save the temperature rising curve in real time for analyze purpose.
-
product
Cable Tracers
180 CB
Standard Electric Works Co., Ltd
● The Amplifier Probe is designed to identify and trace wires or cables within a group without damaging the insulation.● Works with any Tone Generator to identify wires.● Volume control for increased sensitivity and adjustable to suit work environment.● Recessed ON/OFF button prevents battery drain.● A phone jack is designed for headset or handset.
-
product
Wires and Pipe Locator
LKZ-720
*Detection of wires and cables (live or not)**detection of cables in ceilings, walls and floors,**detection of breaks in cables,**tracing cables in building installation,**locating power points and switches in buildings,**locating short circuits between leads,**tracing shielded cables,**tracing cables in metal ducts.*Identification of fuses on the distribution board.*Tracing underground cables.*Tracing conductive water and heating pipelines.*Non-contact detection of live cables.
-
product
Mobile Trace Detection
TR-TRACE
Lightweight, easy to use, real-time trace detection equipment solutions for mobile security screening operations.
