Filter Results By:
Products
Applications
Manufacturers
Thermal Conductivity
See Also: Conductivity Meters
-
product
Thermal Conductivity Apparatus
Objective Thermal Conductivity of Liquids & Nanofluids & Engine Oils etc.
-
product
Thermal Conductivity & Diffusivity Meters
Thermal conductivity, thermal diffusivity and specific heat capacity define a material’s ability to store and transfer heat. The precise and accurate measurement of these properties is critical for any process or material, which experiences a large or fast temperature gradient, or for which the tolerance for temperature change is exacting.
-
product
Portable Thermal Conductivity Analyzer
CI2100-RQD
Shanghai ChangAi Electronic Science & Technology Co.,Ltd
CI2100-RQD portable thermal conductivity analyzer adopts imported high performance intelligent thermal conductivity sensor as measuring unit, which is based on microprocessor. It can test H2 concentration correctly in N2 and H2 mixed gases in a short time. - See more at: http://en.ci-ele.com/dcb675d2-4e33-4eb9-33a0-60edf78c9348/efb4c1eb-f4f5-70af-3ddd-ba6c1066c3fa.shtml#sthash.lXHNyKR1.dpuf
-
product
Non-steady-state probe for thermal conductivity measurement
TP02
Hukseflux Thermal Sensors B.V.
TP02 is a probe that offers the possibility to perform a practical and fast measurement of the thermal conductivity (or thermal resistivity) of the medium in which it is inserted at the highest accuracy level. It works in compliance with the ASTM D 5334-00, D 5930-97 and IEEE 442-1981 standards. The standard TP02 probe has proven suitability in soils, thermal backfill materials, sediments, foodstuff, powders, sludges, paints, glues and various other materials. The Non-Steady-State Probe (NSSP) measurement method (also known as transient line source, thermal needle, hot needle, heat pulse- and hot wire technique) has the fundamental advantages that it is fast and absolute while the sample size is not critical. Hukseflux is specialised in NSSP design. Special models have been developed for in-situ field experiments. For permanent installation in soils, a dedicated model, TP01, is available. TP02 has been designed and tested in collaboration with the Applied Physics Group of Wageningen University.
-
product
Thermal Conductivity Gas Analyzer
CI2000-RQD
Shanghai ChangAi Electronic Science & Technology Co.,Ltd
Determining gas concentrations by measuring the thermal conductivity of the gas, CI2000-RQD analyzer uses advanced thermal conductivity sensor with single chip technology. It adopts platinum thread as sense organ to make up Imbalance Bridge, which output signal has a relationship with tested gas volume. And the single chip will magnify, sieve wavelength, modify linearly and criteria the signal by electric procedure.
-
product
Thermal Conductivity Analyzer
TCi
The default C-Therm TCi Thermal Conductivity Analyzer employs the Modified Transient Plane Source (MTPS) technique in characterizing the thermal conductivity and effusivity of materials.
-
product
Small size non-steady-state probe for thermal conductivity measurement
TP08
Hukseflux Thermal Sensors B.V.
TP08 is a probe that offers the possibility to perform a practical and fast measurement of the thermal conductivity (or thermal resistivity) of the medium in which it is inserted at a high accuracy level. It works in compliance with the ASTM D 5334-00, D 5930-97 and IEEE 442-1981 standards. The TP08 is a small version of type TP02, made for situations where the length of the TP02 poses a problem. The standard TP08 probe has proven its suitability for soils, thermal backfill materials, sediments, foodstuff, powders, sludges, paints, glues and various other materials.
-
product
Thermal Conductivity Analyzers
Teledyne Analytical Instruments
Thermal Conductivity Analyzers by Teledyne Analytical Instruments
-
product
Flat-plate Thermal Conductivity Tester
TESTEX Testing Equipment Systems Ltd.
Flat-plate Thermal Conductivity Tester, to determine the thermal conductivity of various fabrics, quilting products, and other heat insulation materials.
-
product
Field thermal needle system for thermal resistivity / conductivity measurement
FTN01
Hukseflux Thermal Sensors B.V.
The FTN01 Field Thermal Needle System allows performing fast, on-site measurements of the thermal resistivity or conductivity of soils, in particular around the typical depth of burial of high voltage cables. FTN01 is designed with a focus on robustness and saving time, while still offering sufficient accuracy for typical field measurements. The sensor is a Non-Steady-State Probe (NSSP), TP09, which is mounted at the tip of the Lance LN01. The system is operated using a hand-held Control and Readout Unit CRU01.
-
product
Diode Submounts
Ultra-precise patterning of thin film metals on dielectrics with high thermal conductivity are used for diode submount applications. Via the acquisition of Ion Beam Milling, Inc., SemiGen is the industry leader for laser diode submount fabrication. As each application is different, we work with customers to develop a custom design that perfectly fits their requirements. We have experience producing circuits utilizing substrates of varying thicknesses with high thermal conductivity such as alumina (Al), aluminum nitride (AlN), and beryllium oxide (BeO). SemiGen can deliver laser diode submounts with or without Au/Sn pads depending on your needs.
-
product
Heat Flow Meters
Fox Series
Fox Series Heat Flow Meters are reliable, easy-to-use, and durable thermal conductivity measurement instruments. Each of our FOX heat flow meters combines advanced technology with over 20 years of superior engineering. Explore our lineup of thermal conductivity instruments.
-
product
Physical Testing Test
Physical Testing by Aero Nav: mechanical, weathering, environmental, immersion, electrical, luminance, thermal analysis, thermal conductivity, water exposure, saltwater exposure, etc.
-
product
Liquid Thermal Conductivity Instruments
THW-L1
The Transient Hot Wire (THW-L1) Liquid Thermal Conductivity Meter is an advanced measurement system for direct determination of the thermal conductivity, thermal diffusivity, and specific heat instrument for measurement of liquids and pastes in accordance with ASTM D7896-19. The THW-L1 was designed with speed and operational simplicity in mind. With a single measurement of 1 second in duration, small volumes of liquids and pastes can be accurately and precisely measured for thermal conductivity, thermal diffusivity, and specific heat. The THW-L1 utilizes a non-stationary measurement approach and rapid test times to limit convective effects for samples with a wide range of viscosities. The THW sensor consists of a thin heating wire 40 mm in length and is completely inserted into the sample to be tested.
-
product
Portable Thermal Conductivity Meter
TLS-100
The TLS-100 is a portable thermal conductivity meter used to measure thermal conductivity and thermal resistivity at the push of a button. Each TLS-100 comes equipped with a 100 mm sensor for testing soil, polymers, and other soft materials. An optional 50 mm sensor was designed for testing harder materials, like rock and concrete. The collected data is automatically analyzed, and results are displayed instantly.
-
product
Oxygen/Nitrogen by Inert Gas Fusion Infrared and Thermal Conductivity Detection
736 Series
The ON736 Oxygen/Nitrogen Elemental Analyzer is designed for wide-range measurement of oxygen and nitrogen content of inorganic materials, ferrous and nonferrous alloys, and refractory materials using the inert gas fusion technique.
-
product
Cyrogenic Solutions
Our leading edge dewar technology combines the highest quality, reliability and expertise in thermally conductive materials. Our unique designs allow you flexibility to use standard dewars for more than one specific application or test.Minimize cryogenic consumption and maximize thermal conductivity.Vibration isolation to enable the most vibration sensitive applicationsTime-tested ergonomic designs for ease of operation
-
product
Oxygen/Nitrogen/Hydrogen Analyzer
EMGA-930
This is a simultaneous oxygen, nitrogen & hydrogen elemental analyzer with high accuracy and repeatability suiting to cutting-edge technology's R&D as well as quality control in the market of steel, new materials, catalyst and so on. This is a new generation model optimized to fit to user's requests.The oxygen is measured as carbon monoxide and carbon dioxide by two non-dispersive infrared detectors, the nitrogen by a thermal conductivity detector and the hydrogen with non dispersive Infra Red detector as H2O.
-
product
Thermal Conductivity Analyzer
Model 2000B
Teledyne Analytical Instruments
The Series 2000 represents a complete line of Thermal Conductivity Detector (TCD) based analyzers which can be applied in a wide range of applications and industries. By using field proven filament-based and semiconductor based TC detectors, Teledyne is able to continuously monitor hydrogen and a variety of other gases of interest in either binary or multi-component sample gas streams.
-
product
CS/ONH-Analysis
G6 LEONARDO
The high-end thermal conductivity detector used for hydrogen and nitrogen analysis allows detection limits in a sub-ppm range (based on 1g sample mass)
-
product
Thermal properties sensor
TP01
Hukseflux Thermal Sensors B.V.
TP01 is designed for long term (permanent) installation in soils. It covers the thermal conductivity (λ) range of 0.3 to 4 W/m.K, which is sufficient for most inorganic soil types. The core of TP01 is a differential temperature sensor (2 thermopiles) (1) measuring the radial differential temperature with record breaking sensitivity. The sensor performs a temperature measurement around a heating wire (2).
-
product
Oxygen / Nitrogen / Hydrogen Analyzer
ELEMENTRAC ONH‑p 2
The new ELEMENTRAC ONH-p 2 is a powerful and robust elemental analyzer for measurement of oxygen, nitrogen and hydrogen concentrations in inorganic materials like steel, iron, copper or ceramics. The highly sensitive NDIR and thermal conductivity detectors reliably detect element concentrations from low ppm content to high percentages.
-
product
Aluminum PCB
The heat dissipation afforded by this construction is dramatically superior to standard FR-4 constructions. The dielectrics used are typically 5 to 10 times as thermally conductive as conventional epoxy-glass and a tenth of the thickness resulting in thermal transfer exponentially more efficient than a conventional rigid PCB. This is so effective that lower copper weights than suggested by the IPC heat-rise charts can be used.
-
product
CHNO Combustion Services
Carbon, Hydrogen, Nitrogen are determined using a 2400 Perkin-Elmer CHN Analyzer. This analyzer uses combustion to convert the sample elements to simple gasses, i.e. CO2, H2O, & N2. Upon entering the analyzer, the sample is combusted in pure oxygen environment at temperatures in the range of 1200-1500 F. The product gasses are separated under steady state conditions, and measured as a function of thermal conductivity.
-
product
Thermitest
THW-L2
Designed with speed and operational simplicity in mind, the Transient Hot Wire (THW-L2) Liquid Thermal Conductivity Meter is an advanced measurement system for direct determination of the thermal conductivity of liquids and pastes in accordance with ASTM D7896-19. In less than 2 seconds, a single measurement of small volumes of liquids and pastes can be accurately and precisely measured for thermal conductivity. Using a non-stationary measurement approach, the THW-L2 uses rapid test times to limit convective effects for samples with a wide range of viscosities. The THW sensor consists of a 60 mm heating wire that is fully inserted into an isothermal sample. A constant current source (q) is used to heat the sensor wire and the temperature rise is recorded by monitoring the change in electrical resistance of the wire. The slope (m) is determined from the plot of temperature rise vs. logarithm of time and is used in the calculation of thermal conductivity (λ). Liquid samples of high thermal conductivity will have a lower slope, while liquid samples with low thermal conductivity will have a higher slope.
-
product
Thermal Conductivity Transmitter
Model 2000XTC
Teledyne Analytical Instruments
The Model 2000XTC Transmitter resets the standard for thermal conductivity detector based applications with the process control industry. As an intrinsically safe transmitter, packaged within a rugged, weatherproof housing, the 2000XTC is suitable for use in harsh, hazardous outdoor environments. Using a novel, solid-state thermal conductivity sensor, this cost effective transmitter can be configured to detect H2, He, N2 Ar, CO2 a number of other gases of or a number of other gases of interest in binary or multi-component interest in binary or multi-component sample gas mixtures.
-
product
PXIe-4353, 32-Channel, 24-Bit PXI Temperature Input Module
781348-01
32-Channel, 24-Bit PXI Temperature Input Module—The PXIe‑4353 is a thermocouple input module that provides integrated data acquisition and signal conditioning for temperature measurements. The PXIe‑4353 includes increased accuracy and synchronization features for scalable measurement systems from low‑ to high‑channel counts. The high accuracy is attributed to the NI TB‑4353 isothermal terminal block that optimizes thermal conductivity between the thermocouple terminals and the cold-junction compensation (CJC) channels. The PXIe‑4353 has two auto zero channels for offset compensation as well as open thermocouple detection to identify disconnected thermocouples.
-
product
40-CH 100G Thermal AWG
Flyin’s 40 channel 100G Thermal AWG(100G TAWG) is designed for use within the C -band release of DWDM system. To decrease the power dissipation of the devices in different environmental conditions, the TAWG package is special designed with selection of reliable thermal plastic with low thermal conduction, and the TAWG operating temperature is controlled by using foil resist heater or Peltier TEC with thermistor temperature sensor. Different input and output fibers, such as SM fibers, MM fibers and PM fiber can be selected to meet different applications. We can also offer different product packages, including special metal box and 19” 1U rackmount.
-
product
Heat Flux Sensors
MF Series
EKO Heat Flow Sensors are applied to measure the heat flow or thermal conductivity in materials and radiative IR flux emitted by body surfaces. The sensors are suitable for indoors applications, some models made for outdoors purposes and are available in different sizes and thickness. All sensors are extremely flat, which is a big advantage considering the minimum interference with the conditions of the testing area the thermal dynamics. Since sensor foils are relatively flexible those can easy be applied on curved surfaces and can be used in different applications to measure the performance of insulating materials in refrigerators, container walls, pipes, building constructions, etc.
-
product
TIM Tester
The Analysis Tech TIM Tester 1300 is an automated test system for measurement of thermal impedance and conductivity on thin, thermally conductive materials of the type frequently used for electronic packaging, as well as a wide variety of flexible or rigid solids and semi-liquid or viscous materials. Generally, the TIM Tester 1300 can accommodate samples with high-to-medium thermal conductivity with contact pressures ranging from 10 to 550 psi (70-3800 kpa) and at sample temperature ranging from 15C to 70C.
