Filter Results By:
Products
Applications
Manufacturers
Synchro/Resolvers
Compute trigonometric values over 360 degrees of rotation by varying the magnetic couplings between its primary (rotor) and secondary (stators) windings.
See Also: Synchro / Resolver Converters, Angle Position Indicators, Stator, Rotor, Synchros, Resolvers, Synchro / Resolver Simulators
-
product
Synchro or Resolver Angle Indicator Readout
AITM
Computer Conversions Corporation
This series of units were designed to satisfy Hi speed multiturn synchro/resolver applications where the output data must be fresh and no data staleness can be tolerated. The tranducers utilized are the same as in the regular MDS series, however different tracking electronics are used.
-
product
Synchro to Digital-Resolver to Digital Converters
HSDC-HRDC
Computer Conversions Corporation
HSDC & HRDC Series are Miniature, Tracking Synchro and Resolver to Digital Converters with programmable resolution, 8/16 Bit data bus controls, continuous Built-In Self-Test report, and forced angle test modes used for functional validations on command for military and industrial applications.
-
product
Synchro/Resolver
With so-called synchro/resolver cards, rotation angle sensors that work according to the synchro/resolver principle can be measured. Depending on the angle of rotation, these generate a sine and cosine signal, in order to determine the position and direction of rotation.
-
product
Synchro/Resolver Conversion & Simulation PMC boards
Versatile, rugged, and time saving Synchro/Resolver conversion and simulation PMC boards featuring multiple high accuracy, independent channels and easy programmability, to provide a highly accurate and convenient method to test and simulate positioning systems in lab and embedded environments. The SB-3642 conversion and SB-3644 simulation boards’ versatility and ruggedness enable them to be used first in the lab, and then be readily designed into embedded applications, just by the switch of a carrier card.
-
product
Synchro/Resolver to Linear DC Converter
NAI offers a variety of Synchro/Resolver Converters that continuously transform Synchro or Resolver inputs into digital form. These solid-state modules provide resolution to 16-bit and accuracy to 19.8 arc-seconds, and are error-free up to the maximum specified tracking rate. They are transformer-isolated and operate over a frequency range from 47 Hz to 10 kHz. The modules are specifically designed for rugged defense and industrial applications.
-
product
1, 2, or 3 Channels @ 0.5 VA, 1.5 VA or 3.0 VA
DSx
Synchros are transformer-type voltage/current transducers that convert a shaft or other rotating device's angular position and/or velocity to a multi-wire AC electrical signal. Both deliver signals proportional to the Sine and/or Cosine of the shaft angle. A Digital-to-Synchro simulator is used to convert digital angle/velocity commands to corresponding Synchro/Resolver AC signals.
-
product
AC Reference Generators
SR21
Computer Conversions Corporation
The SR Series are miniature, low cost AC reference generators designed to supply 26 or 115 volt excitation to synchros or resolvers in military and industrial control applications. They accept +/-15V DC and provide up to 5VA of transformer isolated output power. These converters are packaged in PC card mounting modules 2.6”x3.1”x1”H.
-
product
Programmable Oscillator Amplifier
Computer Conversions Corporation
The Computer Conversions Corporation POA90-3 is a programmable quadrature oscillator with a built-in power amplifier, capable of driving current loads of up to 200mA. The sinusoidal outputs are 2.5Vrms signals that are phased 90° apart as REF out and REF out +90 (Quadrature), allowing the unit to be used with Synchro, Resolver, LVDT/RVDT, Inductosyn, or similar inductive transducers.
-
product
AC Reference Generators
SR23
Computer Conversions Corporation
The SR23 Series are miniature, low cost AC reference generators designed to supply 26 or 115 volt excitation (2-115VAC) to synchros or resolvers in military and industrial control applications. They accept +/-15V DC or +/-12V DC power inputs and provide up to 5VA of transformer isolated output power. These converters are packaged in PC card mounting modules 2.6”x3.1”x1”H.
-
product
Programmable S/R Standard & Simulator
5300
NAI’s 5300 Synchro/Resolver Standard & Simulator is a laboratory-grade, programmable instrument. This model can be used as a true Synchro/Resolver standard for calibrating and testing Automatic Test Equipment (ATE) for Calibration/Metrology Labs, and for Engineering Design and Production Test environments. It can also be used to measure Angle Position Indicators (API) and Synchro-to-Digital converters for static or dynamic characteristics. This model also may use an external reference waveform.
-
product
PCI D/S, S/D, I/O & Comm Board
76CS3
NAI’s 76CS3 is a PCI/PCIe multifunction I/O and communication board designed for applications requiring Digital-to-Synchro/Resolver (D/S) and Digital-to-LVDT/RVDT (DLV) stimulus output, as well as I/O and communication functions. This full-slot board contains five independent, function module slots. The board can be configured for 6 separate D/S channels, or for D/S in combination with I/O and communication modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
product
DC to Synchro and Linear DC to Resolver Converters
ST-LDS & ST-LDR
Computer Conversions Corporation
ST-LDS and ST-LDR Prefix - Linear DC to Synchro and Linear DC to Resolver Converters On PCB with Mounting Track having Screw-Terminal Block for ease of wiring
-
product
Synchro/ARINC 429/Fuel Flow Modules
NAI designs and manufactures a wide variety of self-contained, remotely mountable, Signal Converter Modules:*Synchro/Resolver Booster AmplifiersS*ynchro/Resolver Converters*ARINC 429-to-Synchro Converters*Second Harmonic Fuel Flow ConvertersTheir field-proven designs and carefully selected components assure highly reliable performance. These military grade modules are specifically designed for rugged defense and industrial applications.
-
product
Solid State Active Synchro Control transformer and Solid State Resolver Control Transformer
Computer Conversions Corporation
The SCT Series are low cost, miniature, solid state control transformers designed for military and industrial control applications. They will directly replace conventional electromechanical control transformers & thus provide digital control to existing analog servo systems. They simultaneously accept a 3 wire synchro input (0) and a digital angle input (0), and provide an ouput which is the sine of the difference between these two input angles (A sin wt sin (0-0) ("wt" is the synchro excitation frequency).
-
product
Synchro Differential Control Transmitter and Resolver Differential Control
SCDX-RCDX Series
Computer Conversions Corporation
The SCDX Series are low cost, miniature, solid state control differential transmitters and resolver transmitters designed for military and industrial control applications. They will directly replace electro-mechanical control differential transmitters (CDX) & thus provide digital control to existing analog servo systems.
-
product
Motion Control Solutions
DDC offers a complete line of Synchro/Resolver instrument-grade cards and test equipment including angle position indication and simulation, plus a variety of hardware and software to meet today’s civil, military, and COTS/MOTS requirements. DDC is a leading supplier of Synchro/Resolver-to-Digital and Digital-to-Synchro/Resolver components—the smallest, most accurate synchro/resolver-to-digital and digital-to-synchro/resolver converters available today. Most of these single chip and hybrid converters are based on ASIC designs, yielding the most reliable and affordable converters ever offered, and are the building blocks for DDC’s card-level products.
-
product
Solid State Synchro Control Transformer and Solid State Resolver Control Transformer
SCT-RCT Series
Computer Conversions Corporation
The SCT Series are low cost, miniature, solid state control transformers designed for military and industrial control applications. They will directly replace conventional electromechanical control transformers & thus provide digital control to existing analog servo systems. They simultaneously accept a 3 wire synchro input (0) and a digital angle input (0), and provide an ouput which is the sine of the difference between these two input angles (A sin wt sin (0-0) ("wt" is the synchro excitation frequency).
-
product
Synchro And Resolver Angle Position Indicator
AP-501
The AP-501 is a high accuracy, auto-ranging, broad band synchro and resolver angle position indicator. The synchro or resolver angle is displayed on a bright 0.56 inch LED display. The indicator maintains a accuracy up 0.03 degrees even with synchro or resolver phase shifts up to 45 degrees over a frequency range of 47-300 Hz. The 800B301 is a low profile rack mounted synchro/resolver angle position indicator with 360 degree offset capability via front panel thumb wheel switches.
-
product
3 Channels, 0.5 VA @ 28 Vrms
DSK
Synchros are transformer-type voltage/current transducers that convert a shaft or other rotating device's angular position and/or velocity to a multi-wire AC electrical signal. Both deliver signals proportional to the Sine and/or Cosine of the shaft angle. A Digital-to-Synchro simulator is used to convert digital angle/velocity commands to corresponding Synchro/Resolver AC signals.
-
product
Programmable Selsyn Indicators
PSI
Computer Conversions Corporation
Computer Conversions Solid State Selsyn/Resolver Indicator digitizes the outputs of Selsyns, Synchros and Resolvers for position indication and control applications. The Selsyn Indicator is designed to replace failure prone mechanical selsyn torque receivers, counters, etc. The tracking converters high noise immunity and high speed tracking characteristics make it ideal for use in industrial envrionments.
-
product
VME-Bus Synchro - Resolver LVDT I/O Cards
VB Series
Computer Conversions Corporation
The "VB Series" product lines contains VME compatible synchro/resolver converters and absolute encoder systems. These particular cards are ideal for any rotary motion and related process, control, or simulator type application with any VME compatible system.
-
product
VXI Synchro/Resolver Module
VX3701
With so-called synchro/resolver cards, rotation angle sensors that work according to the synchro/resolver principle can be measured. Depending on the angle of rotation, these generate a sine and cosine signal, in order to determine the position and direction of rotation.
-
product
Phase Angle Voltmeters
Since the development of the first Phase Angle Voltmeter (PAV) over 50 years ago, North Atlantic Industries has been the industry leader in AC Measurement Instrumentation. Our name has become synonymous with innovation and quality. Our products, specifically designed for defense, industrial, and commercial applications, deliver industry-leading accuracy, repeatability, and reliability.NAI’s units of today are actually multifunction Digital Analyzing Voltmeters that combine a complete Voltmeter, a Phase Angle Voltmeter, and a Waveform Signal Analyzer in a single microprocessor-based instrument. With these versatile and flexible instruments, a wide range of tests can be performed, either manually using the front panel controls or automatically using the IEEE-488 bus. Designed for the Synchro/Resolver and LVDT/RVDT marketplace, NAI’s Voltmeters are used in a variety of applications.
-
product
Handheld Battery Powered Digital Synchro Meter
DSM-4
The DSM-4 is the handheld battery powered digital synchro meter with a large four digit LCD display. It is auto-ranging to accept virtually all standard military synchro signals. The DRM-4 is a handheld battery powered digital resolver meter. A dual range switch provides compatibility with all low-level resolvers ranging from 3.5V to 14V.
-
product
Synchro/Resolver to Digital Converters
Resolvers and synchros are transducers that convert the angular position and/or velocity of a rotating shaft to an electrical signal. Both deliver signals proportional to the sine and/or cosine of the shaft angle. A resolver-to-digital or synchro-to-digital converter converts these signals to a digital output corresponding to the shaft angle and/or velocity. ADI’s family of RDCs and SDCs offer solutions for these applications.
-
product
PCIe Mini Module
PCIe-Mini-SYNCHRO
The PCIe-Mini-SYNCHRO module is a one channel Synchro/Resolver controller. It uses a state of the art 16-bit monolithic Resolver-to-Digital converter. This single chip converter offers programmable features such as resolution, bandwidth, velocity output scaling and encoder emulation.
-
product
AC Reference Generators
SR22
Computer Conversions Corporation
The SR Series are miniature, low cost AC reference generators designed to supply 26 or 115 volt excitation to synchros or resolvers in military and industrial control applications. They accept +/-15V DC and provide up to 5VA of transformer isolated output power. These converters are packaged in PC card mounting modules 2.6”x3.1”x1”H
-
product
PCI Bus Synchro - Resolver - LVDT I/O Cards
PCI Synchro
Computer Conversions Corporation
Proven "Whole" Std. ConvertersOptimized Thermal ManagementExternal Synchro AMP I/O100% Transformer Isolated I/OPermits 2 wire X/Y Stators(Air)No External Parts or Power RequiredReference Powered(NAVAL) Options10-16 BIT Resolution ProgrammableVirtually Indestructible Outputs1.2 to 4.5VA High Power ModelsMix/Match Input & Output TypesSimultaneous Fine/Coarse Transmit For Multispeed Outputs
-
product
Bus Digital-Synchro-Resolver
PC104
Computer Conversions Corporation
The PC104-DS Series are Low Cost, Dual Channel, PC104 Compliant Digital / Synchro / Resolver Output Cards designed to simulate precision AC Synchro and resolver formatted signals for use in navigation and positioning systems or test sets on both industrial and COTS - military type applications.
-
product
4 Digit Angle Position Indicator (API)
TA-900
This has been the New standard in Angle Position Indicators. 4 digit API has fault monitoring for both low-level and loss of signal (LOS) and this status is shown on the front panel led. The unit provides simultaneous connection of both synchro and resolver devices.
