Filter Results By:
Products
Applications
Manufacturers
-
product
Portable Hardness Tester
Handheld Hardness Testers
Handheld Hardness Testers are ideal hardness testing tools where large samples, which cannot be brought to a traditional tabletop hardness tester, or specimens with hard to access areas are to be tested. A wide variety of the portable hardness testers, offered by Qualitest ensure that we recommend the most suitable model for your application. The extensive selection of our handheld hardness testers is available from low-cost economy models up to advanced models coming with more features. These models can measure the hardness of your materials in Rockwell, Superficial Rockwell, Brinell, Vickers, Webster, Barcol scales and often conversions can be done.
-
product
Thermal Shock Test Chamber (Three Zone)
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Thermal Shock Test Chamber (3 Zone) consist of the Test Zone, Heat Storage Zone and Cold Storage Zone. The specimen stay in test zone, hot and cold air will be blew from the storage zones to achieve rapid temperature change for thermal shock.
-
product
Pneumatic Bidirectional Vertical Shock Test System
KRD17 series
KRD17 series pneumatic bidirectional vertical shock test system is the novel designed and developed for large specimens that cannot or are not easy to turn over, especially adopt for battery testing. It can complete vertical upward and downward shock test in one test stand without moving the UUT.
-
product
Compensating Reactor
The compensating reactors are accessories for the CTS-12KSA/ACTS-12K Capacitance & Tan Delta Test Set. The use of one or more compensating reactors increases the capacitance that the internal power supply can excite to conduct measurements. As the measuring range of the CTS-12KSA / ACTS 12K exceeds the kVA rating of the internal power supply, one way of using the test set over its entire measuring range is to form a resonant circuit with the test sample. The use of one or more compensating reactors forms partial resonating circuit with the test specimen, thereby reducing the power supply requirement.
-
product
Magnetic Particle Inspection
Shanghai Xianda Denshijiki Industry Co.,Ltd
Using the "leakage magnetic flux" phenomenon generated from the scratches, the magnetic powder (or fluorescent magnetic powder) of the ferromagnetic material scattered on the surface by magnetizing the specimen is adsorbed to the scratch. Observe this and detect scratches.
-
product
Needle Microprobe
MT-23/8HT
Fast-response 23 gauge needle probe, (needle length is 8 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
product
Samples Preparation (Polisher/Grinder)
* LCD displays all the cutting data.* The diameters of specimens to be cut range from 5 to 8mm (1008:100mm) and the cutting capacity reaches 100x200mm.* Manual cutting and automatic cutting can be changed over at random. * Large cutting chamber & tempered-glass view window.* Non-burnt movable cutting mode which greatly improves cutting quality.● Automatic retract at the end of cutting operation.● Dual-direction feed which increase the depth of cutting.
-
product
Current Compression Flexure Testing Machine
CST-300/200
Jinan Testing Equipment IE Corporation
The Compression and Flexure Testing Machine is mainly designed for compression and bending tests of cement & mortar specimens. The Compression and Flexure Tester for Current can finish compression and flexure tests automatically by one-key action . Computer & software are also adopted to make the operation even easier. With new design and advanced technology, the series of Compression and Flexure Testing Machine have more advantages in appearances operation & applications. The Compression and Flexure Tester for Cement is an ideal tester for quality control at industrial & mineral enterprises, teaching in high schools, and technology researching al scientific industries.
-
product
1 KN Capstan Grips For Yarn And Wire
These capstan grips are applicable for tensile testing yarn and metal wire with thickness less than 3 mm (0.12 in). Flat grip faces are used to hold the specimen. The grip faces are opened and closed by a cam with an operating lever. Ease-of-use and simple design are advantages of these 1 kN capstan grips for yarn.
-
product
Circular Locus Tester
TF225
TESTEX Testing Equipment Systems Ltd.
Circular Locus Tester, to determine surface deterioration and quality of fabrics (wool, chemical fiber, mixed, kitted and woven fabrics). Using an active friction system, fabric is rubbed against a nylon brush and abrasive or an abrasive only under controlled conditions. Results of the test are achieved in minutes. The relative motion of the locus specimen grip and the abrasive platform is a circle with a relative speed of 60+/-1 r/min. The grip offers pressure to the specimen which is adjustable with a tolerance of +/-1%. For added control and safety, the machine is equipped with a self-stop switch.
-
product
Biaxial Clip-on Extensionmeters
The Instron 2650 Series Biaxial Extensometers are ideally suited for testing a wide range of materials, including polymer matrix composites, metals, and plastics over a range of temperatures. Two sensors measure axial strain on opposite sides of the specimen and a third sensor measures transverse strain. The extensometers meet the calibration requirements of ASTM E83 class B1, ISO 9513 class 0.5, and ISO 527.
-
product
1 KN Eccentric Roller Grips
These eccentric roller grips are specifically designed for tensile testing flexible materials, such as rubber and soft and semi-hard plastics. Named after the non-symmetric roller design, these grips employ a simple and quick clamping mechanism. They also have a self-tightening action, which maintains clamping of the specimen during testing regardless of any thickness reduction. In addition, the upper and lower grip faces are parallel grooved to help hold these soft materials.
-
product
Averaging Clip-on Extensometer
The Instron 2650 Series Biaxial Extensometers are ideally suited for testing a wide range of materials, including polymer matrix composites, metals, and plastics over a range of temperatures. Two sensors measure axial strain on opposite sides of the specimen. Versions are available which provide either a single averaged axial output or 2 independent axial outputs. The extensometers meet the calibration requirements of ASTM E83 class B1, ISO 9513 class 0.5, and ISO 527.
-
product
Dynamic Jack System
This is a structural fatigue testing machine for researching the dynamic behavior of full-size or model structures by applying repeated loads. The actuator that supplies the loads to the specimens can be installed on load frames, reaction floors, reaction walls, etc.
-
product
Light Sheet Microscopes
Life science research can place high demands on your imaging capabilities: Sometimes you need to image whole living model organisms, tissues and cells as they develop. Or you may want to observe subcellular dynamics in living samples over hours and even days. Light sheet fluorescence microscopy (LSFM) with its unique illumination principle is ideal for fast and gentle imaging of such specimens.
-
product
Environmental Test Chambers
ET-Series
Environmental Test Chambers are designed with uncompromised features included in the system to meet your changing application needs of simulation of wide range of temperature, relative humidity etc., conditions without the added cost of expensive add-on’s as options. Available in varied volumes to fit your differing specimen sizes
-
product
Impact Specimen Preparation Equipment
Jinan Testing Equipment IE Corporation
DWCT Low Temperature Chamber for Impact Specimen in Drop Weight Testing is specially designed according to ASTM E 208& equivalent ISO Test Method for DWTT of Ferrite Steel Materials. The Low Temperature Chamber adopts multiple compressors, cooling technology and utilizes the heat balance principle and cycle stirring method to realize the constant cooling to impact specimen. With digital display and automatic control temperature, the Low Temperature Chamber is an ideal equipment for cooling and keeping constant temperature.
-
product
Needle Microprobe
MT-23/5HT
Fast-response 23 gauge needle probe, (needle length is 5 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
product
Climate Control Test Chamber
ACMAS's Climate Test Chamber is ideally suited for specimen test requiring quick changes of temperature. It covers various applications from JEDEC and IEC test standards. ACMAS Thermal Cyclic Chamber is equipped with advanced technology such as specimen temperature control which allows linear specimen temperature rates of change during rapid thermal cycling or accurate temperature ramp control. This chamber is also known as Climatic Test Chamber and Climate Controlled Test Chamber.
-
product
Heat Deflection Tester
Apparatus is used to determine the Heat Deflection Temperature or the Vi cat Softening Point. All the specimens are charged with a constant load and immersed in a bath, where temperature is increased at a standard velocity. The attained heat resistance rate of plastic materials is a widely required parameter for product characterization, for quality control, as well as for evaluating their conformity to the previewed applications.
-
product
High Temperature XY Planar Biaxial Extensometer 1200 C or 1600 C)
Model 7651
Jinan Testing Equipment IE Corporation
Model 7651 extensometers measure combined in-plane strains in flat cruciform specimens tested in machines capable of simultaneous X and Y (perpendicular) axial loading and on standard flat samples tested in pure tension. All models are capable of bi-directional displacement in both axes and may be used for strain-controlled fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7651 models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to eliminate crosstalk between axes and to provide high accuracy, high resolution measurements. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods with conical rod tips for specimen contact when testing to 1200℃(2200°F). Silicon carbide rods are used for the 1600℃(2900°F) high temperature option.
-
product
IEC61588 Mandrel Test Device
CX-KD13
Shenzhen Chuangxin Instruments Co., Ltd.
This Mandrel Test Device conforms to IEC60588-1 Fig6 and IEC60065 Fig14--16.The test shall be performed by fixing the specimens of thin sheets on a mandrel made of nickel plated steel or brass with smooth surface finish.
-
product
Textile Tensile Testing Machine
TF002
TESTEX Testing Equipment Systems Ltd.
Textile Tensile Testing Machine, to determine the physical and mechanical performance of tension, tearing, compression, bursting, rapture, flexibility, shear and peel and seam slippage. Especially designed to test a wide range of yarn, fabric, leather, with a huge assortment of specimen grips and software available, it can also be used for strength test of rubber, plastic, metal, wire, paper, packaging, and other materials
-
product
3-Axis Non-Robotic Automated Testing System
AT3
The Instron® TestMaster AT3 and AT3+ Automated Testing System utilizes an innovative design for the automatic tensile and/or flexural testing of plastic specimens. Meeting the testing requirements of ASTM D638 and D790, ISO 527 and 178, as well as other testing standards, this system offers many of the benefits of our robotic AT6 systems, but in a smaller footprint.
-
product
SUNTEST Family
Atlas Material Testing Solutions
SUNTEST instruments are compact material test chambers for accelerated lightfastness and weathering testing based on filtered xenon lamp technology. All SUNTEST chambers offer a horizontal test plane which is particularly useful for testing 3-D specimens. Lightfastness testing aims at testing a material under solar radiation and temperature only – Weathering testing adds water and moisture to the test.
-
product
Shielding Effectiveness/ Conductivity Test
EM-2107A | 30 MHz – 1.5 GHz
The EM-2107A is a standard test fixture for evaluation of the electromagnetic shielding effectiveness of planar material. The fixture is an enlarged section of coaxial transmission line and complies fully with the requirements of ASTM test method D4935-1. The measured data relates to the shielding effectiveness due to a plane wave (far field EM wave) from which near field values for magnetic and electric fields may be inferred. The EM-2107A is provided with a reference standard test specimen, a dynamic range specimen. Dynamic range of greater than 80dB is achievable, although the cables and other test system components usually establishes the limiting factors.
-
product
Pneumatic Flat Grips
For tensile testing rubbers, plastics, elastomers, textiles, cloth, and paper, in specimen geometries such as plates, films, and wires, a good option is pneumatic flat grips. Quick clamping and a repeatable clamping force are advantages of pneumatic flat grips.
-
product
Air Permeability Tester
TF164B
TESTEX Testing Equipment Systems Ltd.
Our Air Permeability Tester determines the resistance of fabrics (woven, knitted and non-woven textile materials) to the passage of air (air flow) under constant pre-set air pressure while firmly clamped in the test rig of selected test head/area.The specimen is loaded to the test area of the instrument easily by means of a pneumatic holder. By pressing down the holder to start the test. The air permeability tester is equipped with a vacuum pump to draw air through an automatic interchangeable test head with a circular opening. The pre-selected test pressure is automatically maintained, and after a few seconds the air permeability of the test specimen is digitally displayed in the pre-selected unit of measure on the touch panel after test the holder is released and the vacuum pump is shut off.
-
product
Hydraulic Servo Control Compression Testing Machine (Four Column)
TYE Series
Jinan Testing Equipment IE Corporation
This series Servo-Hydraulic Compression Testing Machine is mainly designed for compression test of building material items, such as concrete cubes, cement specimen, paver materials and related component, etc. With new design idea and advanced technolog, this series has more advantages in appearance, operation & applications. The compression testing machine is an ideal tester for quality control at industrial & mineral enterprises, teaching in high schools, and technology researching at scientific institutes.
-
product
Auger Microprobe
Auger
It is a high specification Auger electron spectrometer with a hemispherical analyzer to provide high throughput analysis of the chemical bonding state at nano to micro areas, and a field emission electron gun also used for EPMA, because it can deliver a large, stable electric current The highly precise eucentric specimen stage makes it possible to perform the previously-impossible analysis of insulators. This in combination with the floating type ion gun offers the versatility to handle any specimen, such as metals and insulation materials, to obtain composition information to and chemical information.
