Filter Results By:
Products
Applications
Manufacturers
-
product
Serial analyzer
The Serial analyzer sink decodes analog data on a serial bus to serial data. It can be used to monitor and analyze RS232, RS485, MIDI, DMX or other compatible serial buses. The serial analyzer can monitor up to eight sources. When these sources are in sync (all sources are of one (combined) instrument), all captured data will be displayed in chronological order.
-
product
Serial Analyzers
This product enables passive monitoring, debugging, and target system analysis of all speeds of Serial RapidIO Gen2 and Gen1 from the physical coding-sublayer (PCS), through serial protocol, to full-duplex link protocol exchanges. Stimulus transmitters allow for injection of SRIO packets, control symbols, and 8b/10b characters.
-
product
In-Circuit Emulator
DS-51
* Real-Time and Transparent In-Circuit Emulator * Supports Most of the 8051 Derivatives * Emulates 1.5V to 6V Microcontrollers * Maximum Frequency of 42MHz * 64K/512K of Internal Memory with Banking Support * 32K Trace Memory "on the Fly" * 64K Hardware and Conditional Breakpoints * MS-Windows and Keil ?Vision Debuggers * Source-Level Debugger for Assembler, PLM and C * On-Line Assembler and Disassembler * Performance Analyzer * Serially linked to IBM PC at 115 Kbaud
-
product
8 CHANNELS ARINC 429 Simulator Analyzer Tester
CIC429
The CIC429 is a full featured, high performance Serial bus Simulator Analyzer Tester developed by Andor Design for test and simulation of ARINC 429 or similar Avionic buses. The CIC429 is designed as a 5/8 size plug-in card for an ISA bus. An on board microprocessor off loads the host by organizing the data in a predefined structure in the dual port RAM. Programming the CIC429 consists of changing this data, which can be done on the fly for real time applications
-
product
Fifo Serial Analyzer 2 TO 1 Breakout Boxes
FLL221/FLL221S
The FLL221 BreakOut Box is designed to be used with the FLL and FSA serial analyzers when they run on PC's with only one ComPort. The serial line passes through FLL221 using the 9-pin connectors. Data from both pin 2 and 3 of the serial line is available on the FLL221 output. The output cable from FLL221 is connected to the ComPort of the PC running the analyzer.
-
product
PICkit Serial Analyzer
DV164122
The PICkit Serial Analyzer is a low-cost USB-based tool used to direct communication between a PC and an external serial device. I2C™ - Master, I2C™ - Slave, SPI - Master, USART – Asynchronous, USART – Synchronous, LIN (external hardware required to meet electrical specifications), MICROWIRE.
-
product
Simulator / Analyzer / Tester PCI BUS Interface Card
CIC301 - MIL-STD-1553
The CIC301 is a full-featured, high performance, Dual Redundant MIL-STD-1553 A/B serial bus Simulator Analyzer Tester designed as a plug in card for PCI backplane. The CIC301 includes full error injection and can operate in independent or simultaneous mode as a Bus Controller, multiple simulated Remote Terminals and full/selective Monitor. Its data structure can be changed on the fly without interrupting the processor for real time operation. The active monitor stores, time tag and annotates bus traffic with the message type and any detected errors. Stored words are annotated with a break down of the word error.
-
product
Smart Protocol Analyzer
Works transparently over the Computer's I/O ports (serial & network). The analyzer supports Modbus, Fisher-ROC, BSAP, DNP and other Protocols. In addition to monitoring, this tool is capable of simulating Master and Slave devices.
-
product
Fifo Serial Analyzer 2 TO 2 Breakout Box
FLL222
The FLL222 Break Out Box is designed to be used with the FLL and FSA serial analyzers to monitor full duplex bidirectional data. The serial line passes through FLL222 using the 9-pin connectors on the unit. Data from pin 2 of the serial line is available on pin 2 in the first output cable. Pin 3 data is available on pin 2 of the second cable. The output cables can be plugged into the COM ports of the PC running the serial analyzer.
-
product
Fifo Serial Analyzer
FSA32
FSA32 is a Windows based protocol analyzer for debugging serial asynchronous communication. FSA32 uses the standard COM ports of a PC and does not require any other hardware except for the physical connection to the line.
-
product
Fifo Serial Analyzer Breakout Box
FLLBOB
FLL BreakOut Box FLLBOB is a breakout box specially designed to be used with the FLL and FSA serial analyzers. With FLLBOB it is easy to connect the PC to the serial line without having to make dedicated cables.
-
product
Fifo Serial Analyzer for DOS
FLL
FLL is a DOS based protocol analyzer for debugging serial asynchronous communication. FLL uses the standard COM1 and COM2 ports of a PC and does not require any other hardware except for the physical connection to the line.
-
product
Data Analyzer, 8 GHz Bandwidth, 4 Input Channels, 32 GS/s Max Sample Rate
SDA 808Zi-B
8 GHz, 32 GS/s, 4ch, 32 Mpts/Ch Serial Data Analyzer with 15.3" WXGA Color Display.
-
product
Data Analyzer, 16 GHz Bandwidth, 4 Input Channels, 80 GS/s Max Sample Rate
SDA 816Zi-B
16 GHz, 80 GS/s, 128 Mpts/Ch Serial Data Analyzer with 15.3" WXGA Color Display. 50 ohm and 1 Mohm Input, 6.5 Gb/s Serial Trigger, 8b/10b and 64b/66b decode. Also operates in 4ch, 40 GS/s, 64 Mpts/Ch mode.
-
product
Controls Systems for Engine Control and Combustion Analysis
NI Powertrain
NI Powertrain Controls systems incorporate the LabVIEW reconfigurable I/O (RIO) architecture to create some of the world’s most flexible and capable combustion analysis and engine control systems. The engine control systems can drive both solenoid and piezoelectric direct injectors, control timing events with 25 ns of precision, and implement novel engine control strategies such as next- and same-cycle control. The combustion analysis systems are available in both portable and higher performance stationary form factors.
-
product
ARINC 818 Analyser
iWave’s ARINC 818 Video Protocol Analyzer (VPA) instantly verifies the ADVB Packets against ARINC818 Standards. ARINC818 VPA software efficiently captures, decodes the ADVB data, and displays the ADVB data, raw video data, and error status. It is an excellent troubleshooting tool that helps to quickly detect and rectify errors in the ARINC 818-2 applications, simultaneously ensuring compliance of the system with the ARINC 818-2 standards.
-
product
Sound Harmonics and Current Analyzer
H74050100
This analyzer is used as end of line control for electro mechanic components with electric motors, with or without mechanical reduction. While the motor is running at nominal speed, a spectrum and temporal analysis of the sound as well as a current consumption test is performed. Statistical analysis of the data acquired is also performed real-time, expediting the PASS/FAIL decision of the DUT.
-
product
PXIe-7902, 12.5 Gbps, 24-Channel PXI High-Speed Serial Instrument
784232-01
12.5 Gbps, 24-Channel PXI High-Speed Serial Instrument—The PXIe-7902 is designed for engineers who need high-performance FPGA co-processing capabilities or who need to validate, interface through, and test serial protocols. It includes a Xilinx Virtex-7 FPGA to implement various high-speed serial protocols, and it is programmable with the LabVIEW FPGA Module for maximum application-specific customization and reuse. The PXIe-7902 takes advantage of FPGA multigigabit transceivers to deliver 24 TX and RX serial lanes.
-
product
PXI-8430/2 , 2-Port, RS232 PXI Serial Interface Module
778982-01
2-Port, RS232 PXI Serial Interface Module - The PXI‑8430/2 is a high-performance interface for high-speed communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial interfaces also appear as standard COM ports … for compatibility with programs that use serial communications.
-
product
PCIe-8430, PCI Express, 16-Port, RS232 Serial Interface Device
780591-02
The PCIe‑8430/16 is a high-performance interface for high-speed communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial interfaces also appear as … standard COM ports for compatibility with programs that use serial communications.
-
product
PXI-8431, 4-Port, RS485/RS422 PXI Serial Interface Module
778985-01
4-Port, RS485/RS422 PXI Serial Interface Module - The PXI‑8431/4 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
product
PXI-8430, 8-Port, RS232 PXI Serial Interface Module
779536-01
8-Port, RS232 PXI Serial Interface Module - The PXI‑8430/8 is a high-performance interface for high-speed communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial interfaces also appear as standard COM ports … for compatibility with programs that use serial communications.
-
product
USB-485/2, 2-Port, USB, RS485/RS422 Serial Interface Device
778476-02
The USB‑485/2 interface transforms your USB port into a single asynchronous serial port for communication with RS485 and RS422 devices. You can use a USB‑485/2 port as a standard serial port from your application, including RTS/CTS hardware handshake lines. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
product
USB-485/4, 4-Port, USB, RS485/RS422 Serial Interface Device
778476-14
The USB‑485/4 interface transforms your USB port into a single asynchronous serial port for communication with RS485 and RS422 devices. You can use a USB‑485/4 port as a standard serial port from your application, including RTS/CTS hardware handshake lines. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
product
NI-9870, 4-Port, RS232 C Series Serial Interface Module
779891-03
The NI‑9870 adds RS232 serial ports to CompactRIO systems. The serial ports are accessed directly from the FPGA to offer you flexibility in communicating with serial devices. The module has individual buffers on every port that save FPGA space and simplify programming. The NI‑9870 supports standard start bit, stop bit, and handshaking settings. It uses an external power to provide maximum compatibility and reliability under all serial port conditions.
-
product
PXI Vector Component Analyzer, 100 kHz to 32 GHz
M9816AS
The PXI vector component analyzer enables complex multiport device characterization with continuous wave and modulated signal measurements.
-
product
PXIe Network Analyzer Direct Access Receiver
M9377A
The M9377A is one port PXIe Vector Network Analyzer direct access receiver which is used in the M9485A PXIe Multiport Vector Network Analyzer
-
product
NI-9871, 4-Port, RS485/RS422 C Series Serial Interface Module
779892-02
The NI‑9871 adds RS485/RS422 serial ports to CompactRIO systems. The serial ports are accessed directly from the FPGA to offer you flexibility in communicating with serial devices. The module has individual buffers on every port that save FPGA space and simplify programming. The NI‑9871 supports standard start bit, stop bit, and handshaking settings. It uses an external power to provide maximum compatibility and reliability under all serial port conditions.
-
product
PXIe Vector Network Analyzer, 300 kHz to 9 GHz
M9372A
Pay for only the frequency range you need with a choice of six frequency ranges up to 26.5 GHz Improve accuracy, yield and margins with the best PXI VNA speed, dynamic range, trace noise and stability Add functionality to your test system with a full 2-port VNA that fits in a single PXI slot Address your multiport applications needs by cascading multiple models Increase throughput and lower costs by adding modules in a multi-site configuration
-
product
PXIe Vector Network Analyzer Source, 1 MHz To 6 GHz
M9389A
The M9389A PXIe vector network analyzer source is a component for the M9485A PXIe multiport vector network analyzer. The M9389A configuration includes two PXIe modules (M9310A source output, M9309A synthesizer) and its control is provided through the M9385A software front panel (SFP). The M9485A provides a true multiport VNA with up to 12-ports in one chassis and up to 24 ports in two chassis.
