Filter Results By:
Products
Applications
Manufacturers
Screw
See Also: Thread, Linear Actuators
-
product
Run Down Adapters
Screw RDA
The screw run down adapters are designed only for EZ-TorQ analyzer. These devices provide consistent and reliable torque readings for use with power-driven torque control tools. The RDA reduces the impact and irregular peaks that cause poor repeatability. The run down adapter is mounted in-line between the tool drive and transducer.
-
product
Lamp Holder Torsion Test Instrument
Shenzhen Chuangxin Instruments Co., Ltd.
This lamp holder Torsion Test is strictly designed according to UL496 etc. It's mainly used to the screw lampholder torsion test of protecting accidental force.
-
product
DAQ Terminal Board
* Provides screw terminal connections for the Analog, Digital, Relay Driver and Thermocouple signals.* Mates with the 62-pin connector on the 2307 boards and the 2367 Minibox™.
-
product
Tensile tester
TS-2000
Advantage server motor, high quality warm gear gearbox, and precise roll bearing screw are adopted to ensure tensile tester machine the accurate control and results.
-
product
Enclosure, 50 Module, Hinged Cover Plate, 4" Deep
410112199
The Enclosure for the 50 module ITA is made of aluminum, painted black and secured to the ITA by eight socket head cap screws (included). The top of the enclosure is a hinged cover plate with quarter turn hardware that provides easy access to the ITA’s wiring when required.
-
product
Drop-In In-Circuit Test Fixtures
The Chameleon
The Circuit Check kit called the Chameleon allows easy re-use of a majority of an ICT fixture’s major components. The Chameleon includes a full size probe plate and interface alignment plate so all valuable tester resources are available. The probe plate assembly is held in place with twelve (12) screws and the vacuum box’s interchangeable push plate is easily replaced by removing four (4) shoulder screws.
-
product
Odd Shape Assembly Cell
JOT
The reusability of the platform and feeders is close to 80%, allowing the platform to grow and adapt with future business needs. The same cell is easily expandable to automate over 20 different processes and configurable to versatile applications like screw insertion, soldering, laser marking, labeling and packaging.
-
product
Module Accessory Kit, Quantity 26 2-56 x .50" Flat Head Phillips Screws Stainless Steel
510109376
Used with modules: 510104307, 510170101 and 510170102.
-
product
Carbon Monoxide Detector, CO
ENVIROMUX-CMD
Continuous air monitoring. Pre-set alarm points alert at: 70 ppm after 60 to 240 minutes; 150 ppm after 10 to 50 minutes; and 400 ppm after 4 to 15 minutes. Flush or surface mount. Test functionality of electrochemical CO sensing cell. Connect to RJ45 or digital input sensor ports. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Maximum cable length: 1000 ft (305m). LED indicators for operation status and system test. Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: UL.
-
product
Miniature Digital Panel Meter
CSMS-321
Measuring DCA, DCV, Temperature. 1/32 DIN Size ( 48mmX24mm ). Accuracy: +/- 0.1%(DC), +/- 1%(Thermocouple), +/- 0.2%(Pt100). 3 1/2 Digits Display: 1999. Input Max. 2Adc +/- 10%; 300Vdc, T/C type K: 1200J, Pt100:600J. Aux Power 5Vdc +/- 10%; Isolated Aux. Power 5Vdc, 12Vdc, 24Vdc available in option. Easy to wire, screw type terminal. Outside dimensions is 1/32 DIN Standard ( 48 x 24mm ). High stability & low cost.
-
product
TB-2651, Screw Terminal, 8x32, Dual 1-Wire PXI Module Matrix Terminal Block
781131-04
Screw Terminal, 8x32, Dual 1-Wire PXI Module Matrix Terminal Block - The TB-2651 provides the necessary routing to configure the PXI-2531 or PXIe-2531 PXI Matrix Switch Module as a 1-wire dual 8x32 matrix. You can directly connect the TB-2651 to the front panel I/O connectors of the PXI-2531 or PXIe-2531.
-
product
DC Actuators
Electrak DC
Thomson offers Electrak Linear Actuators in DC power versions. With added features and performance capacity, these products follow the quality reputation of our previous designs. From standard to customizable stroke lengths, clevis to trunnion mounts, ball or acme screw drives, and a variety of DC control options, Thomson can provide a fit for just about any application requirement.
-
product
96-Pin Micro-D Connector Block, Male With Backshell
40-965-096-M
This connector block provides a simple method of connecting to 96-Pin SCSI Style Micro-D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
-
product
50-Pin D-Type Male Connector Block
92-965-050-M
This connector block provides a simple method of connecting to 50-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross-sectional area and insulation properties.
-
product
Microscope Cameras
The Imaging Source 13 megapixel microscope camera has been designed to be a cost-effective, versatile solution for demanding microscopy applications. Featuring Sony CMOS technology, this camera comes equipped with a distortion-free autofocus lens which allows viewers to capture exactly what they see through the ocular rather than being limited to a region of interest. This camera can take the place of the ocular itself or can be screwed into the C-mount - eliminating the need for costly adapters. The camera's USB 3.0 interface makes a full HD preview (at 30 fps) on the host PC a reality.
-
product
Cable Assembly, 68 Pin Male Offset VHDCI (Thumb Screws), to 68 Pin Female SCSI (Thumb Screws), 36"
Cable Assembly, 68 Pin Male Offset VHDCI (Thumb Screws), to 68 Pin Female SCSI (Thumb Screws), 36"
-
product
Smoke Detection Sensor - UL Approved
ENVIROMUX-SDS
For warning of smoke. Photoelectric smoke detector. Smoke sensitivity: 0.98-2.4%/ft. Built-in 135° F (57° C) thermal heat sensor. Includes mounting hardware. Connect to RJ45 or digital input sensor ports. Supports CAT5/5e/6 UTP or STP cables. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Operating temperature: 14 to 122°F (-10 to 50°C). Maximum cable length: 1,000 ft (305 m). Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: UL, RoHS.
-
product
Automated Tuners / Impedance Tuners / Load Pull Tuners
MT97x, MT98x and XT98x series automated tuners (also known as automated impedance tuners and automated load pull tuners) are precision instruments that are optimized for a broad class of in-fixture and on-wafer applications, and may be used in any automated or manual application requiring the ability to match the impedance of a microwave circuit element or to establish specific impedances at a terminal interface. The tuner design is based on the slide screw concept using the inherently broadband slab-line transmission structure. Each unit has two non-contacting probes deliver high VSWR with superb accuracy and reliability over a wide frequency range. These probes can be fully retracted leaving a low-loss, well-matched transmission line, which is a significant benefit in power related applications where two-port tuners capable of handling large amounts of power are required. As integral components of Maury Device Characterization Solutions, these PC-based tuners are controlled using Maury's family of Device Characterization Software tools, including MT930 IVCAD, MT993 ATS and the DLL-based measurement automation environment. Maury Microwave automed impedance tuners are ideal for load pull, harmonic load pull, active load pull, hybrid active load pull, noise figure, noise parameters and all automated tuner applications.
-
product
Cable Assembly, 68 Pin Female SCSI (Thumb Screws), to 68 Pin Male SCSI (Spring Latch), 18"
515109119
Cable Assembly, 68 Pin Female SCSI (Thumb Screws), to 68 Pin Male SCSI (Spring Latch), 18"
-
product
TB-2631B , Term Block for NI PXI-2530B 4x32 1W or 4x16 2W Matrix
781688-01
The TB-2631B provides a PXI front-mounting terminal block to configure the PXI-2530B PXI Multiplexer Switch Module. It provides direct signal wire connections to the screw terminals inside the terminal block.
-
product
Polarization Controller and Scrambler - MATRIQ
The Pol 1000 Series enables high-speed automated polarization control for polarization dependent testing procedures.Rotate or scramble the polarization of your signal with no need for manual adjustment of paddles or tension screws using intuitive software, LabVIEW or comprehensive SCPI commands.
-
product
Power Interface Board 3U, 2PSU connectors with AC pins
106PIBM302-9001R
The PIB 3U 2 slot has two power connector P47 with AC pins and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
product
PICMG 2.11 3U CompactPCI 47-pin Power Backplanes
cBP-3061/cBP-3062
- PICMG 2.0 CompactPCI Specification Rev. 2.1 compliant- Design for 47-pin 3U CompactPCI redundant power supply*- cBP-3061 for single power supply, cBP-3062 for dual power supply- AC (and DC) Screw terminal input
-
product
Micropositioner
XYZ 500 MIMT
Quarter Research and Development
Submicron manipulator and translation stage. The XYZ-500-MIMT Micropositioner is intended for precise probing and instrumentation for industrial, medical, biological, semiconductor, and general scientific applications. It provides 3-axis motion with .500" movement on each axis. Motion is controlled by three precision stepping motors attached to precision gear heads 64:1 (standard), that drive a 100 threads per inch screw (standard).
-
product
EZ-Glider Position Control Torque Arms
Equipped with position encoders, the position control torque arm is an error-proofing system that detects and eliminates costly screw-fastening errors during the assembly process. The poka-yoke system reduces the risks of improperly fastening screws, ensuring that every screw is correctly tightened in the correct sequence. In critical applications, tightening fasteners in the correct sequence ensures the reliability of the joint. The position control system is like putting the eyes and ears of a quality control manager where they are needed most – right at each work station.
-
product
Module Accessory Kit, Quantity 26 2-56 x .25" Socket Head Cap Screws Stainless Steel
510109375
Used with modules: 510104306.
-
product
Manual Screw Flat Grips
Screw flat grips are general-purpose grips used for static tensile testing of a wide range of materials, most commonly, rubbers, plastics, textiles, and paper, and specimens such as plates and wires. Another advantage of these grips is they can be used to test thick specimens, up to 16 mm (0.63 in).
-
product
Analog Tank Test Kit
4108
The voltmeter included in the kit, the “Model IA” voltmeter, is designed for ease of use by meter readers and corrosion technicians alike and the voltmeter comes with an integrated RE-5 reference electrode attached for “metallic structure-to-soil” potential difference readings. The kit also includes a special test lead that has a brass thumb screw on one end which allows the test lead to substitute for the RE-5 reference electrode. This substitution allows the voltmeter to take “structure-to-structure” potential difference readings. The voltmeter offers a 0 - 2VDC range with a 10MΩ input impedance and the analog display presents a color divided scale for convenient indication as to whether or not a carbon-steel structure is receiving a suitable level of cathodic protection, with respect to the accepted 0.85V (850mV) threshold value.
-
product
Electric Fatigue Testing Machine
EFT Series
Jinan Testing Equipment IE Corporation
EFT series electric fatigue testing machine is an ideal platform to test a variety of materials and components for the following high demanding tests: Quasi-static test; Reverse-stress mechanical low cycle fatigue loading tests (LCF); High temperature creep, stress-rupture, relaxation tests in load/strain control mode for medium-term or long term period. Mechanical fracture tests like crack growth & toughness tensile/compression test for ceramics in both room- or vacuum-, high- temperatures up to 1200 C conditions etc. Compression test on plate springs or clutch springs etc. It is also widely used to evaluate the mechanical properties of biologic materials, composites, orthopedic fixation devices, prostheses, spinal constructs, stents, dental implants, elastrometric materials, etc. It adopts electric actuator structure with all-elastic, backlash free, central ball-lead screw driving to achieve direct force transmission to the specimen, it is especially a perfect choice for R&D institutes, universities, nuclear power, automotive and aviation, & aerospace sectors from metals, composites, ceramics, springs and component parts.
