Filter Results By:
Products
Applications
Manufacturers
Receptacles
receive conductors.
-
product
Switch Probes
A Switch Probe is a spring contact probe and receptacle combination that is normally open, and after a designated travel the switch probe closes. The most common use for switch probes is in the cable harness testing industry. The switch probe is used to verify the correct location of a terminal in a connector while checking the retention force as well. Switch probes also verify the presence of nonconductive components such as caps for connectors or devices on a circuit board. Smiths Interconnect offers three standard sizes of switch probes.
-
product
Extender
3690-12
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.
-
-
-
product
GPIB PCI Mezzanine Card (PMC) Interface & Cable
GPIB-PMC-XL
The GPIB-PMC-XL is a PCI Mezzanine Card (PMC) GPIB controller card that converts any CPU card with PMC slots into a GPIB controller.It performs all the basic IEEE-488.1 functions such as talker, listener and system controller. The IEEE-488.2 compatible functions make it fully compliant with the IEEE-488.2 specification. In controller applications, you can control typically up to 15 devices (instruments). If operated as a talker/listener (device) interface it does exchange data and state information with the current controller-in-charge of the GPIB bus. The GPIB-PMC-XL lets Windows and Linux programs control GPIB devices.The flat ribbon cable has a standard GPIB jack on one end and a receptacle to be plugged into the GPIB card on the other end. The 30cm (12in) flat ribbon cable is included by Team Solutions, Inc.
-
product
Standard Type Spring Probes
From for bare board to for ICT, we have variety of spring probes for PCB. In addition to variety of tip type and total length, we also have receptacles that match the best to spring probes. We can also attach lead wire to the receptacles.
-
product
Quick Access Recorders
QAR
Two QAR styles are available depending on the features needed, both include our specialized Silo™ Quick Access Recorder Software. Silo QAR with webFB hardware is the ideal certified solution for programs on Boeing 737 aircraft. It quickly attaches to the Flight Data Recorder (FDR) test receptacle and gathers data using the ARINC 717 protocol. For applications on other aircraft or using other protocols, Silo QAR with webCS hardware includes ARINC 429 and Discrete interfaces in addition to ARINC 717.
-
-
product
Circuit Testing
Tester, Circuit GFI
*Use to troubleshoot 120 VAC grounded outlets and test GFCI receptacles*Light sequence indicates correct/incorrect wiring*Lifetime Limited Warranty
-
product
General Purpose Test Probes
Low profile, short travel test probes for restricted space applicationsApplications where long travel is not required such as thin film/hybrid circuits or bareboard PCB testingReplaceable test probe by use of a receptacle
-
product
Universal ZIF (Zero-Insertion-Force) DIP Test Socket
Series X55X
Universal Zero Insertion Force DIP Test Socket. All pin count sockets go into PCB with either .300 or .600 [7.62 to 15.24] centers. Sockets can be soldered into PCBs or plugged into any socket. Socket fits into Aries or any competitive test socket receptacle.
-
product
Extender
3690-2
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.
-
product
Receptacle Tester w/GFCI
61-501
*Warns against faulty wiring in 3-wire receptacles*For use on 120VAC circuits*1-year warranty
-
product
230V AC Socket Tester With RCD Test (For UK)
1944
Peaceful Thriving Enterprise Co Ltd
*With UKCA Approval.*Test for 230VAC circuits.*Neon indicators.*RCD Test.*30mA leakage current measurement.*Detect faulty wiring status in 3 wire receptacle.*Various combinations of 3 neon idnicators tell if wiring is OK or 6 possible faulty conditions.*Power Plug type: UK 13A socket-outlet*Measurement Category: CAT II / 1.5W*Frequency: 50Hz
-
product
Voltage Testers
Electrical Receptacle Tester Instantly Displays Wiring Condition of Any Standard 3-Wire AC 110-120 OutletNeon Indicators Give Positive Indication of Current StatusCompact Unit Simply Plugs into any Standard 3 Wire/Grounded Receptacle (110–125 Volt AC Circuits)Tests for 6 Circuit Conditions: Open Ground, Open Neutral, Open Hot, Hot/Ground Reverse, Hot/Neutral Reverse & Correct WiringBlister PackedcULus ListedOrder Qty of 1 = 1 Piece
-
product
Tester, US Mains Socket
72-6861
The 72-6861 is a Receptacle Tester with 3-indicator light. 2nd-Amber indication for ground contact (Open ground) and 3rd-amber indication for neutral contact (Open neutral) not connected, for hot and ground contacts interchanged indication by red and amber. If 2-amber indication occurred, receptacle is wired correctly.
-
product
Extender
3690
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.
-
product
MEASUREMENT QUALITY JUMPERS
4000-1065
This kit includes two (2) Singlemode Enhanced MQJs (ST-to-Socket, 1 meter, SinglemodeEnhanced), two (2) Singlemode Enhanced MQJs (ST-to-Pin, 1 meter, SinglemodeEnhanced), two (2) Multimode MQJs (ST-to-Socket, 1 meter, Multimode), two (2)Multimode MQJs (ST-to-Pin, 1 meter, Multimode), two Snap Lock Plugs, and two SnapLock Receptacles.
-
product
Electrician & Technician Testers
EVSE's Electrician and Technician testers are created for installation professionals, and are small and durableenough to be carried in a toolbox. These weatherproof handheld units allow new chargers to be checked after installation, verifying a number of vital power and safety requirements, as they simulate the connection a charger makes with an electric vehicle. Simply plug the charger's J1772 connector into the tester's receptacle and you are ready to evaluate operation.
-
product
180V-260V AC Socket Tester (For UK)
1941
Peaceful Thriving Enterprise Co Ltd
*With UKCA Approval.*LED indicators & Digital display.*Test for 180-260VAC circuit.I*t can perform self test after plug-in ( Voltage sould be above 180V ).*Detect faulty wiring status in 3 wire receptacle.*This socket tester will give LED indication as well if the main voltage is below 200V or above 260V.*Earth loop impedance test.*Power Plug type: UK 13A socket-outlet*Measurement Category: CAT II / 4W*Frequency: 50Hz
-
product
110-125V AC GFCI Receptacle Tester
1934B
Peaceful Thriving Enterprise Co Ltd
*With UL and cUL Approval.*Detect faulty wiring in 3 wire receptacle.*Test for GFCI receptacle for proper operation, 110-125V circuits.*Various combinations of three lights tell if wiring is correct or six possible faulty conditions.
-
product
MU Cable Tester System
16814
The MU Locomotive Trainline/Cable Test System (MU Test System) can perform shorts testing, continuity testing, and ground-leakage testing on each of the 27 pin Multi-Unit Trainlines normally found on Freight Locomotives. The MU Test System is comprised of two identical tester units. Each unit is installed in a rugged, water resistant Pelican case. Each unit contains an MU cable receptacle that mates with a 27 pin MU jumper cable. A snap-on vinyl pouch on the outside cover of each unit provides storage for the battery charger/power adapter and the chassis test lead. The enclosure cover hinges separate from the test unit as the cover is opened; this removes the cover completely to allow free access to the MU cable receptacle and the control panel.
-
product
GFCI Receptacle Tester
RT600
Designed to detect the most common wiring problems in standard 120V receptacles.Also tests GFCI receptacles for proper operation.Test for correct wiring, open ground, reverse polarity, open hot, open neutral, hot and ground reversed.Conditions NOT indicated: Quality of ground, multiple hot wires, combinations of defects, reversal of grounded and grounding conductors.Large light indicators for greater visibility.Reinforced prongs for increased durability.Push-pull design with slip-resistance ribbing.
-
product
110-125V AC GFCI Receptacle Tester
1934
Peaceful Thriving Enterprise Co Ltd
*With UL and cUL Approval.*Detect faulty wiring in 3 wire receptacle.*Test for GFCI receptacle for proper operation, 110-125V circuits.*Various combinations of three lights tell if wiring is correct or six possible faulty conditions.
-
product
Super-Safeway Receptacle Tension Tester
1301270007
Super-Safeway Receptacle Tension Tester & Receptacle Tension Tester in Carrying Case
-
product
12-600V AC Adjustable Non-Contact Wire Tracer
5220
Peaceful Thriving Enterprise Co Ltd
This non-contact voltage tester, can be used to test the presence of AC voltage from 12V~600V, no need of metallic conduction, easy to read by visual and audio indication. Locates breaks along live, insulated wires and power cords. Adjustable sensitivity allows tracing of wires behind walls, around switches or receptacle.
-
product
Extender
3690-6
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.
-
product
Variable Power Supply
VS3
The VS-3 power supply is a very convenient portable, non-isolated “variable source” from 0 volts to 150 Vac or 0 volts to 150 Vdc and rated for up to 3 amps, thus the name VS-3. It is comprised of an illuminated voltmeter that reads to the first significant digit, AC variable system output voltage, DC variable system output voltage, logic output voltage and one sense (continuity) contact monitoring points. Banana jacks for connection of test leads are spaced at intervals that allow the use of dual banana test plugs if desired. The VS-3 is protected by two levels of overcurrent protection; AC input, and ground fault protection by a GFCI. All circuitry is housed inside a custom designed case made from 16 gauge steel. An Internal fan dissipates heat buildup and exhaust through louvered side vents built into the case. The carrying handle is designed with a “spring return to rest” position and is padded for comfort. The case has been sized for optimum portability and is balanced from the handle during transportation. The case has a powder coated finish that is scratch, chemical and weather resistant. Rubber padded feet support the case when in the upright position and a convenience receptacle is located on the side of the case. A unique feature of the VS-3 is that it contains “Magnet Packs” on the back of the case. These “Magnet Packs” can support the VS-3 and allow it to “hang” from any magnetic metal surface. The VS-3 can be powered by our UPS system, eliminating the need for an extension cord. The ability to magnetically attach the VS-3 near the source of connection and eliminating the need for an extension cord makes the VS-3 a “must have tool” for technicians.
-
product
Hand Insertion Tools
Zierick Manufacturing Corporation
Ideal for low volume, short run and prototype PCB assembly applications, Zierick’s hand tools offer a simple and reliable method for inserting press fit and splay mounted terminals. The hand tool can be easily installed on any type of press machine for increased flexibility and faster insertion. With the addition of a lower tool die, terminals can then be splayed and locked into place to improve reliability and prevent part removal and rotation. Zierick hand tools are available for PCB-mounted quick-disconnect terminals, quick-disconnect receptacles, post receptacles, test points and IDC terminals. Simple and reliable method for inserting press-fit and splay mounted terminals. Single tool can handle multiple terminal insertion applications. Tools can be installed on almost any type of manual or pneumatic press. Please click here for a PDF user manual for Zierick's hand tools.
-
product
Electrical Receptacle Tester
ERT100
UEi Test & Measurement Instruments
The ERT100 is a rugged, well-designed and well-built electrical receptacle tester. Featuring 6 different results with indicator lights for outlet condition, making it easy to read. With over molding and a comfortable grip, it fits comfortably into your hand. And is backed by a 1-Year limited warranty.
