Filter Results By:
Products
Applications
Manufacturers
-
product
Multi-Band Dual-Channel Receiver/Combiner, Modular Unit with Integral Tracking Receivers and Bit Syncs
LS-28-DRSM Series
Lumistar offers the LS-28 series of high performance multi-band multi-mode RF Receiver/Combiners in several different versions including rack mount, portable and modular formats. Complete solutions from RF to bits and/or RF to UDP data broadcast in Chapter 10 format are available. Available at any frequency range from 215 MHz to 6000 MHz, data rates to 50 Mbps.
-
product
ATR Enclosures
Elma Air Transport Rack (ATR) enclosures offer a standardized, cost effective solution for VME, VME64x, CompactPCI, VXS, VPX and Small Form Factor (SFF) based applications.
-
product
VME Radar Processing System
Signal Processor is Standard 19' rack mount chassis. 400 Hz, 3-phase, 115VAC aircraft power is available. Typical system can handle 200 MB/s (minimum) input data (also output data since we record the input data). Options include 10 GigE, Infiniband, FibreChannel or Serial FPDP. Optional 1GigEthernet for output products, parameter data, control messages, etc.
-
product
G12 - 12 Module Solution
For maximum versatility and easy access to instrument-side wiring and cable assemblies, VPC offers a selection of slide kits designed to fit most common rack depths. All slides are rated to support 180 lbs (81 kg) to accommodate even the largest fixtures. To order, measure rack depth between mounting rails. With this measurement choose the slide mounting kit that fits the rack. A rack extender kit is available for mounting to racks with recessed rails.
-
product
S6 Rack Mount
The S6 Rack Mount receiver is ideal for consolidating multiple test instruments and only occupies 1U of rack space. This low-profile makes it ideal for in-line test applications. The S6 receiver will support an ITA/fixture weight of 50 lbs. at 6”.
-
product
cPCI Backplanes
CompactPCI bus is compatible, in terms of electrical specification, with the PC world’s PCI bus. The mechanical specifications were adapted to the commonly used Euro-board plug in systems for 19" racks.
-
product
Capacitance Sensor Systems
MTI Instruments offers high resolution capacitance sensors, probes and systems that generate low noise, highly accurate and high stable measurements. Our Capacitance sensor line-up offers accurate measurements for automated inspection applications such as thread quality inspection, disk drive run-out, leveling or flatness measurement, lens alignment, tire run-out and bulging. Our Accumeasure capacitive sensors offer large stand-off distance that includes single and multiple channel rack systems that connect up to 10 capacitive sensors or capacitance probes with individual analog measurement outputs. We also offer cost-effective customized capacitive sensor amplifier board and probe system for easy integration. Our inspection systems linearity exceeds 0.01% full scale measurement (FSM) and resolution to sub nanometers.
-
product
VPC Receiver Frame
ABex REC21-84TE-EXT
Robust and flexible interconnect solution for test fixtures. Designed for the use with ABex PXIe Rack 18 it provides support to equip all 21 slots with VPC interconnect modules. In addition, it offers 6 more slots on the bottom, below the ABex rack to feed through signals from external measurement devices.The interface uses the well-known Virginia Panel connectors with more than 20.000 guaranteed mating cycles. To build DUT specific test fixture, we also provide the corresponding ITA mounting frame (ITA = Interchangable Test Adapter).
-
product
Measurement System
MS-500 series
The MS series is suitable for pre-processing analog signals.The plug-in units of filters, differential amplifiers, isolation amplifiers, etc. can be installed into their frames.(16 channels at maximum/the JIS rack size)
-
product
Engineering Support Platform
ESP
ESP, or Engineering Support Platform, is a low cost, powerful and versatile platform for the development, deployment and support of FPGA Applications. ESP is powered by DSX core, ARC’s core element for the development and deployment of digital and mixed signal systems. The standard system contains 2 custom FPGA system, often configured in combination where one acts as the application firmware, and the other is used for test. But the system is expandable and configurable in any combination to solve any problem in a digital, analog or mixed signal system. The FPGAs can be configured to generate, analyze, process and/or output complex signals at a wide range of voltages, frequencies and serial protocols. It has been used to develop solutions for Radar systems, testers, Pattern Generation, digital signal processing and generating, Video processing, and many more. ESP comes as a desktop or rack mounted solution, and no special interfaces are needed.
-
product
Dispersion Compensating Fiber
Dispersion compensating fiber from M2 Optics is used for correcting dispersion effects created over distances within G.652 single mode optical fibers. Offered in a 19" chassis for rack or benchtop use, these high quality testing platforms are easy to work with and provide consistent, repeatable results.
-
product
30"D Retractable Writing Shelf for 24" Racks
WS-022430
24" x 30"D retractable writing shelf operates smoothly on ball bearing slides which lock in fully extended position.
-
product
Rack Mounted Load Banks
Traditional commissioning is a daunting task. Since formal system operation doesn’t begin until the system is commissioned, the commissioning team experiences intense pressure to complete the commissioning process quickly. Commissioning can involve high expense and requires staffs from different departmental disciplines to work together. For these reasons data center commissioning has almost uniquely been associated with large data centers (over 20,000 ft2 or 1,858 m2). In the recent past, many data center managers chose to roll the dice and perform little or no commissioning, relying only on start-up data to press ahead with launching the new data center. Given the reality of 24x7 operations, however, the alternative of exposure to major system failures and accompanying downtime is no longer an economically viable option. Commissioning has now become a business necessity. JUNXY series AC & DC rack mounted load banks can be used to introduce heat loads and to allow for simultaneous testing of both electrical and cooling systems.
-
product
Autosampling Dissolution Tester with Built-In Sample Collector
Vision AutoPlus & Vision AutoFill
The Vision® AutoPlus™ is a modern upgrade of the popular Hanson legacy AutoPlus™ autosampler. The Vision AutoPlus comes with a choice of 6 or 8 sampling channels, and DissoScan™ (1-bath) or Maximizer™ (up to 3 baths) configurations. Precision syringe pump mechanics, all-inert tubing and valves, and color touchscreen programming with up to 100 protocols are standard on each instrument.The Vision® AutoFill™ is a sample collector designed for seamless integration with the Vision AutoPlus to save space and to provide a 360 degree view for visual monitoring of the collection process.. Vision AutoFill accessories include choice of collection racks with 13 x 100 or 16 x 100 mm test tubes for UV-Vis, 12 x 32 mm vials for HPLC, sample trays with 12 x 32 mm vials for UPLC®, and more.
-
product
20" Slide Kit, Fits 20"-22" Deep Racks, Supports 180 lbs
310113409
20" Slide Kit, Fits 20"-22" Deep Racks, Supports 180 lbs.Measure rack depth between mounting rails to determine the slide mounting kit that fits the rack. An extender block kit is available for mounting to racks with recessed rails.
-
product
Mission Critical, Fault Tolerant Power Supplies
Series HSF
- Hot-swappable plug-in power supplies.- Designed to be combined in an N+1 fault-tolerant power system.- Front panel voltage adjustment trimmer for adjustment of output voltage.- Built-in forced current sharing and or-ing diodes.- May also be used independently as a multi-output power supply.- Designed to be sustainable - new models are backward compatible with existing racks.- Available in 1U and 3U sizes. Mounts in 19-, 23-, and 24-inch equipment racks.- All models include power factor correction (PFC).- Full service customized DC power distribution systems can match power supply output(s) with your load(s).- I/O connections via 24 pin connector that plugs into rack adapter. External connections are made via rack adapter.- Surface mount technology permits minimum mounting space.- Entire RA 19 racks populated with HSF power supplies can be connected in parallel, parallel-redundant or series.- HSF are CE Marked per per the LVD, EMC and RoHS 2 Directives. See applicable Declaration of Conformity.- Compliant with UL 8750, Standard for LED Equipment,- Watch video of NEBS GR-63-CORE earthquake and office vibration testing.
-
product
Subrack Enclosures
IEC 60297
Beijing Rdekono Electronic Equipment Co.,Ltd.
As a professional 19-Inch Subrack Manufacturer, our Networking Racks and 19-Inch Subracks are meticulously crafted to meet the highest industry standards, ensuring optimal performance and reliability. Designed with precision and attention to detail, our products offer a robust and efficient solution for housing and organizing electronic components.
-
product
3U / 6U PXIe Chassis
The GX7100e Series are 14-slot combination PXIe chassis that accommodate a 3U PXIe embedded controller or a MXI express controller as well as 3U & 6U PXI / PXIe insruments in 4U of rack space. The GX7100e’s unique format includes seven 6U slots and seven 3U slots arranged horizontally to reduce the overall size of the chassis, providing the versatility and high-density necessary to address many PXI / PXIe applications and requirements. The backplane architecture supports Gen 2, 4x4 PCI Express bus signaling and the use of both x1 or x4 system controllers. By offering a combination of PXI-1, Hybrid, and Express slots, the GX7100e offers users the ultimate in flexibility for general purpose as well as high bandwidth test needs.
-
product
EDFA For CATV, FTTH And HFC Applications
MX-A5400 series
The EDFA is suitable for long haul transmission networks or FTTH distribution networks. This optical amplifier is packaged in a 19” rack mount housing to provide a complete optical communications solution. Maxcom offers our MX-A5400 platform which can be ordered with 8, 16, 32, 64, 128, 256 and 512 output ports and various output powers.
-
product
Receiver, G12, 12 Module, Rack Mount
310104338
Receiver, G12, 12 Module, Fixed Rack Mount Unit 15" Platform Supports 275 lbs
-
product
Rack Mount Power Supplies
AC-DC High Voltage Power Supplies
Ideal for laboratory and instrumentation applications, these rack mounting supplies have the same output ratings and specifications as the modular supplies, but additionally feature calibrated ten-turn controls (with locking vernier dials) for precisely setting voltage and current. Voltmeter and ammeter are standard. An 8' long shielded output cable is included.
-
product
DISCRETE TMTC INTERFACE BOX
The Discrete TM/TC Box is a 6U custom 19’’ rack equipment that could be filled with 6U, 4HP plug-ins covering the main ECSS compliant discrete I /Fs. The I/O signals of this box are all arranged in the rear side of the box, keeping clear the front side: in this way no accidental operation could be performed on the box.
-
product
Flush Mount Rack Kit For M9018A
Y1215B
Y1215B is a rack-mounting kit that suspends the chassis in a Keysight rack using 4 U of rack space. It includes rack flanges, handles, and attachment hardware.
-
product
Emergency Power Supply Units (EPSU) (10) 5-20R 1U/0U V/H
EPS-1020-HV
EPSU Power (Basic / Surge / Metered / Value) – rack mountable power distribution, 120V, optional surge suppression, and amp meter
-
product
2450 MHz Industrial Microwave Generators
Alter® 2450 MHz Industrial Microwave Generators are built on MKS Alter® Product experience and designed with rugged and reliable switch mode power supplies for demanding industrial applications. They offer compact generators up to 3kW in a 19 inch standard rack with a remote head and integrated isolator.
-
product
Mini Rack 60*60*60cm
OTP2 module no.001
The rack serves as the basic structure for your individually designed test system. Various OTP² modules can be installed in the 60 x 60 x 60 cm rack in order to implement a wide variety of test requirements.
-
product
LS-28-1U Chassis Combined AUX Cable Assembly
28U-CBL-AUX3
Cable assembly for LS-28-DRSM 1U Rack Mount Unit
-
product
6TL23 Off-Line seat operation Base Test Platform w/o Table
H71002301
- 18U height 19inch rack space (580mm depth)- VPC G12 or G12X interface- Man Machine interface H73000301 (not included)- stand-up operation
-
product
6TL23 Off-Line Seat Operation Base Test Platform
H71002300
The 6TL23 is a bare rack for creating Off-Line, modular, flexible and reliable Base test platforms. The overall rack capacity is 18U (580mm depth). The rack is ideal for sit-down operation, since there’s space for the operator’s legs under the fixture receiver.
-
product
Xenotest Xenon-Arc Instruments
Atlas Material Testing Solutions
These premium rotating rack, xenon-arc air-cooled weathering instruments have an array of optional features to meet virtually all global weathering and lightfastness test methods. They incorporate state-of-the-art controls, including on-the-rack, radio controlled sensor technology for superior monitoring of light and temperature. They provide highly efficient systems for water and power to provide economical operation. The intuitive user interface makes programming and operation easy.
