Filter Results By:
Products
Applications
Manufacturers
RJ45
Common name for any 8P8C modular connector.
-
product
cRIO-9066, 667 MHz Dual-Core CPU, 256 MB DRAM, 512 MB Storage, Zynq-7020 FPGA, 8-Slot CompactRIO Controller
783169-01
667 MHz Dual-Core CPU, 256 MB DRAM, 512 MB Storage, Zynq-7020 FPGA, 8-Slot CompactRIO Controller - The cRIO-9066 is a rugged, fanless, embedded controller that you can use for advanced control and monitoring applications. This software-designed controller features an FPGA, a real-time processor running the NI Linux Real-Time OS, and embedded user interface capability. Additionally, the cRIO-9066 features an SDHC slot and a variety of connectivity ports, including one tri-speed RJ-45 Gigabit Ethernet, one USB host, one USB device, and one RS-232 serial. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
product
PCB Adapter, ITA, VTAC, to (2) USB 5 Gbps (USB 3.0, USB 3.1 Gen 1, USB 3.2 Gen 1) and (4) RJ45 Connectors
510171114
Mates with p/n 510170114.Please note: The RJ45 connectors extend beyond the width of the module. Care should be taken when installing in positions adjacent to other PCBs. Please contact VPC, if further assistance is needed.
-
product
Professional LAN Installation Tool kit
CTK400LAN
The StarTech.com Professional LAN Installation Tool kit provides all the necessary tools to install and test RJ45 networks in a compact, handy, carrying case.
-
product
Carbon Monoxide Detector, CO
ENVIROMUX-CMD
Continuous air monitoring. Pre-set alarm points alert at: 70 ppm after 60 to 240 minutes; 150 ppm after 10 to 50 minutes; and 400 ppm after 4 to 15 minutes. Flush or surface mount. Test functionality of electrochemical CO sensing cell. Connect to RJ45 or digital input sensor ports. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Maximum cable length: 1000 ft (305m). LED indicators for operation status and system test. Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: UL.
-
product
VTAC, Patchcord, ITA, 36", VTAC, CAT6A FTP, to RJ45 PLUG
7-141705694-036
VTAC, Patchcord, ITA, 36", VTAC, CAT6A FTP, to RJ45 PLUG.
-
product
Optical Power Meter & VFL & RJ45 Network Test
TM263N
◇ Added Network Cable Test ◇ Accurately test whether a single network cable transmits signals normally ◇ Self Calibration ◇ Set the Auto Off ◇ Wavelength Memory function after turn off the tester ◇ High Accuracy, high ,High sensitivity, high linearity ◇ Stable VFL Output ◇ USB Charge port ◇ FC,SC Connector ◇ 18650Li-ion Battery ◇ Lower power consumption design, long standby time ◇ Rubber Out shell, increased the protective properties for field work
-
product
Smoke Detection Sensor - UL Approved
ENVIROMUX-SDS
For warning of smoke. Photoelectric smoke detector. Smoke sensitivity: 0.98-2.4%/ft. Built-in 135° F (57° C) thermal heat sensor. Includes mounting hardware. Connect to RJ45 or digital input sensor ports. Supports CAT5/5e/6 UTP or STP cables. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Operating temperature: 14 to 122°F (-10 to 50°C). Maximum cable length: 1,000 ft (305 m). Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: UL, RoHS.
-
product
16-CH Discrete Input 16-CH Discrete Output Modules
HSL-DO16-UC / HSL-DI16-UC
- Support 16 DI channels and 16 DO channels- Transmission speeds: 3/6/12 Mbps- RJ-45 phone jack for easy installation- Compact design to meet space limitation and cost-effective requirement- Fuse design to protect digital output channelover-current
-
product
3U CompactPCI 9th Gen Intel® Xeon®/Core™ i7 Processor Blade
cPCI-3520 Series
The cPCI-3520 Series is a 3U CompactPCI blade available in single-slot (4HP), dual-slot (8HP) or triple-slot (12HP) width form factors with various daughter boards to provide a broad range of I/O requirements. Faceplate I/O in the single-slot (4HP) version includes 1x DVI-I, 2x GbE and 1x USB 3.0 port (these I/O are common to all versions). Faceplate I/O in the dual-slot (8HP) version includes additional 2x USB 2.0, 1x COM, 1x KB/MS and Line-in/Line-out on the cPCI-3520D or additional 2x DisplayPorts, 1x COM in RJ-45 connector, 1x KB/MS and 1x additional USB 2.0 port on the cPCI-3520G. Two more dual-slot options are the cPCI-3520L with additional 2x GbE, 1x COM and 2x USB and the cPCI-3520M with one 100-pin high density connector supporting additional 2x DVI-D, 2x USB 2.0, 2x COM, 2x KB/MS and Line-in/Line-out ports.
-
product
Mini OTDR 1310/1550nm with OPM, iOLM, LS, VFL and RJ45
TR1000
Shenzhen Sharingtek Communication Co., LTD
Fiber & RJ453.5 Inch Color LCD8 Functional Modules24dB Dynamic RangeiOLM-Event Map3m Event Dead Zone60km Precision Testing
-
product
Rear-Panel I/O Transition Module
CP3-GESW8-TM8
CP3-GESW8-TM8 is a rear-panel I/O transition module providing flexible access to CP3-GESW8 or NETernity™ CP3-GESW8N rear-panel I/O. Up to eight Gigabit Ethernet ports of the switch are accessible from the transition module's stacked RJ-45 connectors. Each Ethernet port is routed as four 100 Ohm differential pairs.
-
product
8-Ports Gigabit Ethernet RCV Interface
YAV90058C
8x RJ45 LAN connectors to VPC RCV 192 pins module
-
product
Digital Input/Output Expander (Open-Collector Outputs)
ENVIROMUX-DI16DO16
Adds 16 digital inputs and 16 digital open-collector outputs to the ENVIROMUX-2D/5D/16D. Interfaces with the ENVIROMUX-2D/5D/16D via the RJ45 Sensor Port. Digital inputs: 16 screw terminal pairs for connecting dry contact devices; One screw terminal pair for tachometer; 0 to 255 Hz. Accepts 26 to 16AWG wire. Potential free. Voltage range: 0 to +36VDC. Over-voltage surge protected. Digital outputs: 16 screw terminal pairs for open-collector outputs. Accepts 26 to 16AWG wire. Rated sink current: 500 mA per output. +5VDC, 22kΩ pull-ups. Voltage range: 0 to +24VDC. Over-voltage surge protected. Supports CAT5/5e/6 cable up to 500 ft. (152.4 m). Powered by ENVIROMUX-2D/5D/16D. Compatible with ENVIROMUX-2D/5D/16D. Dimensions WxDxH: 6.49x3.10x1.08 in (165x79x27 mm). Regulatory approvals: RoHS.
-
product
Multi-purpose Cable Tracer and Non-contact Voltage Detector
168 CB
Standard Electric Works Co., Ltd
● Four transmitter plug types - RJ-11 - RJ-45 - COAX - Alligator clips ● Two unique audible tones: - Fast alternating tone - Slow alternating tone ● Telephone line polarity check - Tip side - Ring side● Cable tracing ● Telephone line status check - Clear line - Busy line - Ringing line ● Continuity check.● Transmitter plug storage.● Easy to store different kinds of transmitter plugs (RJ-11, RJ-45, COAX, and alligator clips).● Easy to carry.● Flashlight function.
-
product
Cable Assembly, Receiver, QuadraPaddle, 72", 2 RJ45 Plugs
540224010540
Cable Assembly, Receiver, QuadraPaddle, 72", 2 RJ45 Plugs
-
product
Interface Board, Compact, 8:1 Ethernet RJ45
40-965-907
Compact converter card for 40-736 Data Communications Multiplexer. Adapts the 78-Pin D-type connector on the front of the module to 9 RJ45 sockets. Allows the multiplexing of up to 8 Ethernet signals with speeds up to 1G bit.
-
product
Value-added Module With 4 RJ-45 GbE LAN And PoE
VAM702/VAM703
*4 x RJ-45 LAN or PoE/PoE+*Swappable modular design*Maximize I/O flexibility*Designed for tBOX300/500 series*LVD, FCC, EN 50155 and IEC 60945 certified; CE compliant
-
product
Outdoor Temperature Sensor
ENVIROMUX-STS-O
Applications from -40 to 185°F (-40 to 85°C). Accurate to within ±0.9°F (±0.5°C). Weatherproof enclosure. High resistance to external influences on the cable due to digital output signal. Re-calibration is not necessary after initial set-up. Quick release waterproof RJ45 connector. Supports CAT5/5e/6 cable up to 1,000 ft. (305 m). Powered by ENVIROMUX-2D/5D/16D. MTBF: 1,942,123 hrs. Compatible with ENVIROMUX-2D/5D/16D. Regulatory approvals: CE, RoHS.
-
product
VTAC, Patchcord, ITA, 36", VTAC, CAT6, To RJ45
7-141893694-036
VTAC, Patchcord, ITA, 36", VTAC, CAT6, to RJ45
-
product
Multi-Modular Cable Tester
MT-7051N
Tests RJ45 TIA568A/B (AT&T 258A), 10 Base-T, Token ring, RJ-11/ RJ-12 USOC and Coaxial BNC cable.Automatically check cable for continuity, short, open and crossed wire pairs.Coaxial cable port indentifies cable conditions including shorts, shield opens and center conductor breaks.Main unit and remote allow one person testing.Power source: DC 9V BatteryDimension: 102x106x28 (mm)Cable not include
-
product
Installation Tester
M75
Installation tester for safety tests according to IEC/EN61557-1 with TRMS multimeter functions and test of cable mapping on lan RJ-45 networks
-
product
Turnkey Laboratory Acquisition Systems
Series 6800 for laboratory applications is a ready-to-run, high performance measurement system. Enclosures are 3U rack mountable or can be used right on the desktop. 6800 units come equipped with a conditioner, amplifier, filter and digitizer. Each channel has a front mounted connector specific to a measurement type: RJ-45 for 8-wire bridge transducers, BNC for voltage or ICP/IEPE inputs or a 3-wire military grade connector.
-
product
48-Channel High Performance Strain Gauge Measurement Instrument
EX1629
48-Channel High Performance Strain Gauge Measurement InstrumentSupports quarter-bridge (120, 350Ω or user defined), half-bridge or full-bridge24-bit ADCs, sampling rates up to 25 kSa/sBuilt in programmable differential excitation -8V to 8VBuilt in selectable bridge completionConfigure signal conditioning excitation and bridge completion on a per channel basisSimple, low-cost wiring using RJ-45 telecom connectorsSupports TEDS for easy transducer detection and setupRJ-45 input connector reduces setup cost and timeBuilt in self-calibration and shunt calibrationSupports voltage, ratiometric and linear measurements other than strain measurements.
-
product
Light Intensity Sensor
ENVIROMUX-LIS
Detects and measures the luminous intensity of light. Ideal for monitoring unmanned closets, telecom rooms, remote data rooms, or other low traffic facilities. Applications from 0 to 128,000 lux. Human eye response (540 nm peak sensitivity). IR and UV rejection. RJ45 connector. Supports CAT5/5e/6 cable up to 1,000 ft. (305 m). Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: CE, RoHS. Compatible with ENVIROMUX-2D/5D/16D.
-
product
RJ45 (Ethernet 100 Base T) to 90 Series Interface (R)
J90RJ45R
RJ45 Ethernet connector for VPC Tripaddle 90 series RCV moduleUp to three connectors per moduleFor Cat 5 Fast Ethernet cable IEEE 802.3 standard100 Base-T
-
product
Network Analyzer, Lan Tester, LED
72-6290A
The 72-6290A is a multi-modular Cable Tester (LAN Tester) with LED meter display. Requires 9V battery for this modular cable tester. Used with RJ-45, RJ-12, RJ-11 connectors and USOC4, USOC6, USOC8 cables.
-
product
Remote Cable Tester for RJ45 RJ11 USB and BNC
REMOTETEST
Troubleshoot your wiring problems, quickly and affordably with StarTech.com's REMOTETEST, a Specially designed network wire tester that saves valuable time and effort when testing RJ45, RJ11 and BNC cables.
-
product
Legacy Liquid Detection Rope Sensor
ENVIROMUX-LDSx-y
For warning of flooding. Detects liquid depth >0.1" (2.5 mm). Minimum puddle: 0.6" (15 mm) diameter. 100% waterproof electronics. Detects any liquid or moisture, except deionized water. RJ45 connector. Voltage Supply: 12VDC. Current Consumption: 20mA. Supports CAT5/5e/6 cable up to 1,000 ft. (305 m). Available water sensor cable (x) lengths: 1/10/50/100/200/400/600/800/1000 feet. Plenum rating: CL2P (UL). Available 2-wire cable (y) lengths: 5/10/20/50/100 feet. Powered by ENVIROMUX-SEMS-16U and SERIMUX-S-x. Regulatory approvals: CE, RoHS. Requires the ENVIROMUX-SEMS-16U and SERIMUX-S-x to operate. Use self-adhesive clips (ENVIROMUX-CLP10-LD) to prevent sensor rope cable from shifing after installation. ENVIROMUX-CLP10-LD includes 10 clips.
-
product
Glass Break Detection Sensor
ENVIROMUX-GBS
Acoustically detects the cracking of glass. Adjustable sensitivity. Includes mounting hardware. Connect to RJ45 or digital input sensor ports. Supports CAT5/5e/6 UTP or STP cables. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Maximum cable length: 1,000 ft (305 m). Powered by ENVIROMUX-2D/5D/16D.
-
product
PRO Banjo Pro Line Tester
TC-BJ100
The Banjo Pro features convenient testing in both data and POTS environments. The black RJ45 plug is used for testing in eight conductor environments. "Just Flip It" to the red RJ11 plug for testing of two, four, and six conductor POTS environments.
