Filter Results By:
Products
Applications
Manufacturers
Phase Standards
verify Phase Meters, Vector Voltmeters, Broadband Wattmeters and Power Analyzers, Resolvers and other Phase Sensitive Instruments.
See Also: Phase, Phasing, Phase Meters, Phase Angle, 3 Phase
-
product
Multifunctional Meter
CPM-80
Chuan Sheng Electronics Co., Ltd.
CPM-80 multifunction power analyzer provide high accuracy single phase and three-phase energy measuring and displaying, energy accumulating, power quality analysis, data logging and data communication. CPM-80 series meters are able to measure bidirectional, four quadrants kWh and kVarh. It provides maximum/minimum records for power usage and power demand parameters. Hardware standard built in a RS485 Modbus communication port , 4 Digital inputs, 2 Relay outputs, LCM and 2MB flash for data-logging. In addition , also provide TOU , voltage and current THD, harmonics up to the 63rd and auto wiring change via software .
-
product
Solar Analyzers
Max. solar system power (Pmax) search by Auto-scan: 1000V, 12A (12000W capability)The analyzer and the Remote Solar Detector is connected by Bluetooth wireless communication (Bluetooth 2.1 + EDR Class 1)The Remote Solar Detector is moisture-proofIntelligent test logic with no personnel attendance required in the field Solar system analyzer waits and tests the system until appropriate sunlight irradiance is detectedMax. voltage (Vpm) at Pmax, Max. current (Ipm) at Pmax Voltage at open circuit (Voc), Current at short circuit (Isc)Efficiency (%) calculation of solar systemTemperature measurement of solar panelsIrradiance measurement of sun lightSeries resistance (Rs) calculation of solar panelsWith data logging/open function, the I-V curves of solar system can be analysed / recorded for a period of time (e.g. 60 min.)Conversion of I-V curve under OPC to data under standard test condition (STC) based upon IEC standardProvide Operating Condition (OPC) and Standard Test Condition (STC) test reports for verification of solar panel performance (OK or NO OK)Users can set up the parameters of solar panelsUsers can set up the series number of solar panels. Parameters of many solar panels can be measured in one measurementThe Irradiances and Temperatures of solar panels can be continuously measured, monitored and recordedContinuously measure/monitor/record the DC power output of solar system and the AC power output of inverter (1 phase or balanced 3 phases)Calculate the efficiency of DC to AC power conversion and the efficiency of the max.output power
-
product
Environmental Chamber
REXMED REC-200
MOD. REC-200, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -20˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 1.5KW X 2pcs, Humidity heater: 2.5KW X 1pc, Heat up transition time: -20˚C~100˚C within 35 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 1,892 Watts, 6,455 BTU/hr, 1,630 Kcal/hr, Cool down transition time: 20˚C~-20˚C within 45 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L50 X W60 X H75cm, Capacity: 225L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
product
Computer Control 6-Phase Relay Protection Tester
GDJB-PC6
Chongqing Gold Mechanical & Electrical Equipment Co.,Ltd
1.This tester with standard 6 phase voltage, 6 phase current output,2.Voltage 125V/phase, current 30A/phase, 6 phases in parallel can up to 180A.3.Digital Signal Processor Microcomputer.4.Not only test the traditional relays and protectors, but also test the modern micro computer replays, special for transformer differential protection and transfer equipments.
-
product
Phase Verification Bridges
5002
Clarke-Hess Communications Research
The Model 5002 Phase Verification Bridge set comprises passive devices that are used in conjunction with Model 5500-2 Phase Standard and an output null indicator such as a true rms voltmeter, an oscilloscope or a wave analyzer to verify that the Phase Standard is continuing to operate within its specified phase accuracy limits.
-
product
Comb Generator, 10 MHz to 50 GHz
U9391F
The Keysight Technologies, Inc. U9391F comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
product
Comb Generator, 10 MHz To 110 GHz
U9391M
U9391M comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
product
Radio Frequency Cable Tester
RFCT
Textron Systems’ Radio Frequency Cable Tester (RFCT) allows for on-site testing and maintenance for radio frequency (RF) transmission paths within a platform. Using preconfigured databases of sweep parameters and pass/fail criteria, the RFCT quickly determines the status of installed RF cables. The RFCT checks each cable’s performance characteristics to include voltage standing wave ratio (VSWR), insertion loss (IL), phase and phase matching. If a cable fails a test, the RFCT automatically determines the distance-to-fault (DTF). With its intuitive touchscreen-based user interface and lightweight, ruggedized packaging, the RFCT is the gold standard for operational-level RF cable testing.
-
product
VDI Millimeter-Wave Frequency Extension Modules for PXA, MXA, EXA Signal Analyzers
These modules offer low conversion loss and excellent noise figure. Standard features include dual operating modes. First, the module can function as a high performance down-converting mixer. The second operating mode functions as a block down-converter with a broadband IF up to 20 GHz. Power to the module is provided via an included external DC power supply. These frequency extenders minimize conversion loss by multiplying and amplifying the LO signal internally, thus taking advantage of the benefits of low harmonic mixing. This architecture also preserves the X-Series precision frequency resolution and low phase noise, extending those qualities into the millimeter and sub-millimeter bands.
-
product
Multifunctional Meter
AEM-DRA
Chuan Sheng Electronics Co., Ltd.
The AEM-DRA series has 2 independent and isolated main circuit inputs , can use for different power system.Up to 24 single phase or 8 three-phase circuits, programmable from push buttons with LCM display panel, or using Adtek program software through RS485 communication port.Hardware standard built in a RS485 Modbus communication port , 2 Digital inputs, 4 Relay outputs, LCM and 2 MB flash for data-logging.Optional second communication port for Ethernet, ProfiBus ,LonWorks ,BACnet and Zigbee solutions.Din rail mounting , compact and easy installation, programming through computer and push buttons easy to use.
-
product
EMC Testing
Does your product send or receive electromagnetic data? This can be analyzed using various tests. We investigate the interference immunity and emitted interference of simple electrical devices and complex machinery. Our EMC measurements and tests conducted in accordance with standards recognize all activity in the electromagnetic field and ascertain how immune to interference a piece of equipment is. We will also offer guidance on optimizing the product in terms of its EMC properties during the development phase.
-
product
Comb Generator, 10 MHz to 26.5 GHz
U9391C
The Keysight Technologies, Inc. U9391C comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
product
Audio Test Software
1. Distortion free stimulus even the equalized stimulus.2. Unlimited channels acquisition and processing. (Hardware limited)3. Human correlated listening test(Bark Scale intensity chart). (Requires large memory)4. Hi Res intensity chart for buzz/pop detection. (Requires large memory)5. Auto equalization method with target dBSPL accuracy.6. TCP client for test framework integration.7. Easy limits and logs development.8. Easy logs visualization module.9. Auto waveform alignment and triggering.(Upto single point alignment accuracy)10. Easy regression testing via TCP client.11. Standard Magnitude, Phase, THD, THD+N, Rubb&Buzz, Pink Noise, Noise Tests.12. Unlimited calibrations and equalization for scaling to different products and stations.13. Lowest test system and test sequence development times.14. Requires minimal training and debugging.15. Automatically avoid Reference speaker play and stop pops.16. WMD/ASIO driver compatible sound cards supported.(B&K 3670 recommended)
-
product
90 Degree Hybrid Couplers To 500 MHz
Hybrid couplers with bandwidths as broad as 125:1 are available for applications within 100 kHz to 500 MHz. Power handling is 1 watt maximum for a load VSWR of 1.2:1 or better. These hybrids have an isolation of 20 dB and phase balance of 3 degrees. Most models have a VSWR of 1.4:1 or better throughout their operating bandwidths.Pulsar Microwave currently offers these hybrid couplers packaged in three outlines, including an SMT version. Standard offering of connectorized packages 412 and 442 are with SMA female connectors. Outline 412 may be customized with any combination of BNC, TNC, F or N connectors. Outline E is the surface mount version and requires less than one square inch of board area, making it well-suited for portable applications.
-
product
Power and Energy Automated Calibration System
RS-933
The RS-933 Syntron Power and Energy Automated Calibration System calibrates a range of test equipment including; Energy Reference Standards, Digital Multimeters, Phase meters, Energy meters, Power meters, Revenue meters, Amp meters, Panel meters & Power Quality meters.
-
product
Low G Sensitive Oscillators
Precision Test Systems is increasingly becoming a world leader in ultra-low phase noise (ULN) crystal and rubidium oscillators. We manufacture the CFS10B crystal frequency standard and the RFS10E and RFS10F rubidium frequency standards. All these models can also be locked to the global satellite service operated by the USA (GPS), Russian (GLOSNASS) and Europe (Galileo). We also have a complete range of distribution amplifiers to compliment these frequency standards.
-
product
Audio Generator
AG-51
The AG-51 Audio Generator contains a low distortion 20 Hz to 200 kHz sine wave generator, an SMPTE standard intermodulation signal generator and a fixed frequency sine wave generator at 3.15 kHz for wow and flutter tests. Signal outputs are simultaneously available at levels of up to +20 dBm (equivalent sine wave power for complex signals) at separate left (L OUT) and right (R OUT) output connectors. Outputs may be selected for left (L) only, right (R) only, left and right in phase (L+R), and left and right in phase opposition (L-R). Fully balanced or unbalanced outputs at impedance levels 150 ohms or 600 ohms are front panel selectable. Three precision attenuators (10, 1.0 and 0.1 dB) provide a dynamic range of 99.9 dB in 0.1 dB steps. Attenuator dials display the output level directly in dBm in the 150 ohm source impedance configuration. Automatic output leveling circuitry with a built-in self-test feature provides a constant output level thereby eliminating the need for output metering. In the TEST mode the generator output level is reduced to zero, a useful feature during noise measurements.
-
product
Three Phase Power Analyzer
930A
Model 930A Three Phase Power Analyzer is an economical alternative to the Model 931A Power System Analyzer when the dc voltage measurement, transducer calibration and timer features are not required. The Model 930A has the same ac accuracy as the Model 931A with PowerDSA™ Digital Signal Analysis. Basic accuracy of 0.05 % of reading and 0.05 ° phase, harmonic analysis, and full three-phase capability are standard.
-
product
Signal Generators
SSG5000X Series
SIGLENT’S SSG5000X series of signal generators can generate analog and vector signals, and have a frequency range of 9 kHz to 4 GHz/6 GHz. They feature the industry-leading performance in phase noise, spectral purity, bandwidth, EVM, output power. The internal IQ modulation generator and waveform playback function make it easy to create even the most complex signal types. They also cover the most important RF band for digital wireless communications and include standard waveform files. The SIGLENT SSG5000X are powerful and cost effective sources that are ideal for R&D, education, and manufacturing.
-
product
Volume Production Oscillators
Volume production oscillators utilize either high performance GaAs Gunn diodes with high Q cavity designs or state-of-the-art FET devices with dielectric resonators to yield excellent phase noise and stability. These oscillators are free running with extremely high frequency and power stability. The oscillators are generally designed and manufactured for fixed frequency applications. However, fine frequency adjustments can be achieved by mechanically tuning the provided self-locking screw. While the below standard models are offered for immediate production release, custom models are also available.
-
product
Vector Network Analyzer
R42XXE
The R42XXE Vector Network Analyzers are designed for measuring of S-parameters, VSWR and impedance of waveguide networks in the full frequency ranges of standard waveguides between 33 and 170 GHz. Frequency accuracy is ±0.2%. The measurement range of reflection factor modulus is from 0 to 1. The measurement range of reflection factor phase is from 0 to ±180° for 0.1< |Гx|<1 with accuracy ±7.5 o in 18-75 GHz frequency range and ±9.6° in 75-170 GHz frequency range. The measurement range of transmission factor phase is from 0 to ±180 o with accuracy ±(5+0.1 |Ax|) o for Ax >-50 dB in frequency range to 75 GHz, for Ax >-30 dB - to 170 GHz. Data can be displayed in the rectangular, Smith or polar diagrams. VNA requires Personal Computer with USB interface.
-
product
Energy Meters
Bofa Instrument & Equipment Co., Ltd
Energy meter is a new type of single phase electronic energy meters, which completely accords with international standard IEC61036. It can display energy consumption by stepping-motor counter or LCD. It features good reliability, small volume, light weight and convenient installation.
-
product
Multifunction Electrical Installations Meter
MPI-520
The MPI-520 multifunction meter is dedicated to perform diagnosis of electrical installation according to IEC 61557 standards. Digital meter MPI-520 is designed to measure impedance of a short cicuit loop also without triggering RCD, parameters of RCD, insulation resistance, earthing resistance, continuity and also for phase sequence testing. Furthermore to measure and logging of AC voltage and current, frequency and power.Wide range of standard accessories enable to perform all necessary measurements and safety test. Highly professional portable multifunction meter with memory of measured parameters.
-
product
GeoSwath Module
The GeoSwath Plus Sonar Module contains a wide-swath bathymetric sonar suitable for a range of survey and inspection tasks. The GeoSwath Plus is a 500kHz interferometric sonar, or phase detecting bathymetric sonar (PDBS) from Kongsberg GeoAcoustics. Boat-mounted GeoSwath sonars are used worldwide for high accuracy surveys including port and harbour navigation and environmental mapping: the Gavia’s GeoSwath module makes this capability available in a commercial AUV. The GeoSwath Plus offers: wide swath coverage of up to 12 times the AUV altitude when near the seabed; integrated bathymetry with simultaneous true digital side scan; high depth resolution suitable for IHO survey standards; as well as the accuracy and repeatability of a boat-mount hydrographic survey system. Like most of the survey-grade sensors on the Gavia AUV, the GeoSwath data is time-synchronised with the AUV master clock using the vehicle PPS/ZDA system. Benefits of the GeoSwath AUV module include ease of deployment, ease of use, reducing survey time, and the ability to take a 500kHz high-resolution sonar down to targets in 1000m of water. The GeoSwath Plus post-processing software (provided as standard with the system) allows a user to inspect and process the data, create and inspect digital terrain models, and create basic sonar mosaics. Several other commercial post-processing software packages are also available, please ask for details. Note that for best results the GeoSwath Module should be deployed with a direct-reading sound velocity sensor (option) in the Control Module, and one of the high-accuracy INS/DVL Navigation Modules for motion sensing.
-
product
Thermal FFF
TF2000
The new award winning Postnova TF2000 Thermal FFF Series was invented to become the first professional modular Thermal FFF system available. It is completely integrated by the NovaFFF single software platform which runs the entire system from autosampler to detectors. The TF2000 Series incorporates the combined solid know-how and the proven technologies from three decades of leadership in FFF. Due to its unique design, the TF2000 Thermal FFF system offers more flexibility, higher robustness and better performance than traditional chromatographic systems. No separation column with stationary phase is required anymore and consequently the TF2000 technology sets a complete new standard and offers a real alternative to column-based polymer characterization techniques.
-
product
Safety
Chroma Systems Solutions, Inc.
The purpose of safety testing medical electronic equipment is to be sure that a device is safe from electrical hazards to the patient and caregivers. There are a number of UL, European and Canadian standards that serve as the ruling body on how medical products will be tested, one in particular, IEC60601 (the International Electrical Safety Standard for medical electronic equipment) is experiencing “global harmonization,” meaning it has been accepted and implemented around the world. The IEC60601 standard is mainly intended for product development where safety considerations must be taken into account early in the design phase of a product, however much of it is applied to production line testing since it is the only way for a manufacturer to be sure they are shipping safe product.
-
product
Multifunctional Meter
CPM-70
Chuan Sheng Electronics Co., Ltd.
CPM-70 multifunction power analyzer provide high accuracy single phase and three-phase energy measuring and displaying, energy accumulating, power quality analysis, data logging and data communication.CPM-70 series meters are able to measure bidirectional, four quadrants kWh and kVarh.It provides maximum/minimum records for power usage and power demand parameters. Hardware standard built in a RS485 Modbus communication port , 4 Digital inputs, 2 Relay outputs, LCM and 2 MB flash for data-logging.
-
product
Multi SDI Monitors
LV 5333
LV 5333 Waveform Monitor is a powerful, versatile video production tool that is compact and portable. LV 5333 has a high quality TFT LCD screen which produces high quality picture images. Waveform, Vector, Audio, Status and 5 Bar gamut displays are all included in this precision instrument. These can be displayed full screen or in various multi-display combinations. LV 5333 can also display the levels of an embedded audio signal. Plus, Cable Length, External Phase Difference, and Field Frequency Deviation measurements are standard along with CINELITE® II. Now with HD HDR monitoring as an option, the LV 5333 can be carried as a portable unit or rackmounted for studio or flypack use.
-
product
Single Phase Din Rail Multi-Tariff Energy Meter Type DDS999D
Bofa Instrument & Equipment Co., Ltd
Single phase Din rail multi-tariff energy meter type DDSF999D is a new type of single phase electronic multi-rate energy meter, which accords international standard IEC61036. It features: good reliability, small volume, light weight, convenient installation, etc.
-
product
Mechanical Tunable Phase Shifters
The phase shifter features a high resolution precision micrometer which allows for finer adjustment sensitivity than a standard micrometer. The phase shifter is an ideal piece of equipment in waveguide systems where broadband phase shifting is required. The phase shifter exhibits a 2.5 dB typical insertion loss and an adjustable phase range of up to 180 degrees.
