Filter Results By:
Products
Applications
Manufacturers
Integration
-
product
Integrated Flight Controller
Kratos Defense & Security Solutions, Inc.
The Integrated Flight Controller (IFC) controls the entire flight functionality and maneuverability of the BQM-167 subsonic aerial target platform. The IFC accepts commands from a ground control system (such as GRDCS, SNTC, or TTCS), inputs current vehicle operating parameters from onboard sensors, and outputs control signals to the vehicle for flight control. The IFC supports multiple high performance maneuvers, such as barrel rolls, high G turns, and low altitude operation.
-
product
Modulation Distortion Up To 43.5 GHz
S930704B
S930704B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 43.5 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930704B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
product
ISDD Tool Suite
The Integrated System Diagnostic Design or ISDD Tool Suite provides a start to finish solution for meeting all the diagnostic needs of system design. The ISDD design process is centered around functional modeling of systems which is used to develop the diagnostics and failure analysis necessary to fully support good system design. This includes: *Analysis of Fault Detection and Fault Isolation.*Analysis of critical failures and their impact upon safety.*Detecting and reducing false alarms caused by diagnostics.*The impact of prognostics upon fault detection/fault isolation and mitigation of critical failures.*Development of vehicle health management and troubleshooting diagnostics
-
product
Surface Resistance Meter
WL MIDGET
WL MIDGET Surface Resistance Meter is an ultra-wide range, battery operated, portable instrument for measuring Surface Resistivity and Resistance to Ground of virtually any flat surface conforming to ASTM D-257 standard method by using recommended parallel bar sensing probe. Gives simple, repeatable measurements of conductive, static dissipative, and insulative surfaces. Ranging is automatic due to the use of high-speed OP-AMP Integrated circuits being linear, with changeover points +1/2 decade on a logarithmic scale. Repeatability equals + 5%.
-
product
Integrated Clamp-On Ultrasonic Flowmeter
KATflow 210
The KATflow 210 is a portable flowmeter designed for situations that require a reliable flow measurement regardless of the conditions in which it needs to be operated. With its advanced battery technology and durable waterproof housing the instrument is intended for long-term installation in remote areas where access to power is limited and exposure to the worst of elements is likely.
-
product
Components for System Integration
Bh offers a wide range of accessories to improve your photon counting experiment such as experimental control modules, optomechanics or implantable fiber probes for in-vivo applications. For PMTs and MCPs we offer different preamplifiers and a variety of routing devices for multi-detector operation. For a perfect SYNC signal, trigger modules and a SYG are available.
-
product
Coordinate Measuring Machines
StentCheck®
High performance multisensor CMM with Integrated Werth Zoom® optic with magnification 0.7x – 6.8xRotary/Tilt Axis with high speed air bearing rotary axisRotary OnTheFly for fast measurementsContour image processing for fully automatic measurements of complex geometrical elements with sub-micron repeatabilityIntegrated goniometer (tilting axis) allows for the measurement of non-cylindrical geometriesUnique lighting design optimized for measurement of stentsTemperature compensation included
-
product
Systems Integration (SIL) Lab Data Acquisition
Bloomy’s SIL data system allows testing and simulation of every system component on the aircraft. The functionality of these complex integrated systems are fully tested, debugged, and verified safely in the lab prior to flight testing. This reduces cost and schedule for new aircraft. Bloomy has applied its expertise to multiple SILs.
-
product
YIG Integrated Products
With a 30 year YIG heritage, Teledyne RF & Microwave integrates YIG components with related microwave technologies, creating custom solutions that leverage the advantages of YIGs in cost-effective assemblies including synthesizers, receivers, converters and more.
-
product
16/8 Channel 14-bit 250 MS/s Digitizer
VX1725 / VX1725S
The VX1725S family comes in a VME64X form factor, with 16/8 input channels. The communication to and from the board is provided through the VMEBus and Optical Link interfaces. The VX1725S is a digitizer capable of recording waveforms along with performing advanced algorithms for online digital pulse processing (DPP). Utilizing DPP Firmware, users can acquire quantitative physical parameters (Integrated Charge, Pulse Shape Discrimination with very fine time resolution, Pulse Height Analysis) as well as read out waveforms with automatic pulse identification and baseline suppression on channel basis (Zero-Length Encoding and Dynamic Acquisition Window).
-
product
Pyrometer With Integrated Controller
thermoMETER CS
The infrared thermoMETER CS temperature sensors are equipped with a miniature sensor that is particularly suitable for installation in confined spaces. The small size and temperature resistance up to 120°C open up a wide range of applications.
-
product
Electronic Load
* Fully programmable, self-contained, air-cooled solid state load.* Patented design is optimized to provide ultra-low impedance operation for fuel cell testing.* Load is compatible with AC impedance or frequency response analyzers.* Interchangeable shunts for precise operation over a wide dynamic range.* Ten built-in cell voltage monitoring inputs optional. Additional voltage monitoring inputs available.* Ethernet Interface for simple configuration and expansion!* Combine with additional Fideris™ Innovator Series™ modules to create a fully-integrated,fully-automated, customized test system.* System-wide control of all Fideris™ Test System Components using FCPower™ Software,LabviewTM, or other programming language.* Integrated hardwired Run/Standby signal.
-
product
BIM Structural Modeling Services
Structural Modeling represents the digital replica of structural components of a building i.e., beams, columns, torsion, and foundations, using Autodesk Revit software. Tejjy-BIM Inc. provides Revit Structural BIM design-drafting-modeling services for concrete & steel structure building design. Integration of BIM modeling in structural engineering facilitates better analysis of design detailing and simulates the behavior to coordinate and collaborate with the architectural & MEP (mechanical, electrical, and plumbing) system. BIM services in structural engineering facilitates structural analysis, and optimization of building design, as well as generate fabrication and construction documents.
-
product
Integrated Function Tester for Inductance Ballast
UI2001B
• Measure input parameters: Vrms, lrms, W, PF, Hz, current crest factor, total harmonic and 0~50th harmonic components. V range: 10.0~300.0V, A range: 0.010~2.000A, F range: 45~65Hz • Measure output parameters: Vrms, lrms, W, PF, Hz, current crest factor, total harmonic and 0~50th harmonic components Lamp voltage range: 10.0~450.0V, Lamp current range: 0.010~2.000A • Accuracy: ± (0.4% reading+0.1% range+1 digit) • Can test every kind of curve, print both data & curve • Communication interface available for PC, running under Windows98/2000/XP/Vista
-
product
Integrated Receivers/Demodulators/Bit Synchronizers
Lumistar provides a wide variety of rack mount integrated receiver and diversity combiner systems. Some of these can be configured with multiple receivers, diversity combiners, and bit synchronizers depending on custom requirements. Lumistar does not manufacture any computers, but selects only the finest of the industrial machines available to provide a high performance package. Basic system setup, control, and display software is included with each of these systems at no additional cost.
-
product
COTS Integrations
Sundance Multiprocessor Technology Ltd.
Our “COTS” Integrations are some examples of what could be achieved with combinations of our carriers and FMC modules.They are systems for data acquisition, signal generation, video processing and more.
-
product
Temperature Humidity Vibration Comprehensive Integrated Test Chamber
THV-1000
Can match appropriate vibration table. Meet all kinds of the corresponding temperature, humidity, vibration, three comprehensive test requirements. Widely used in aviation, aerospace, shipbuilding, electrical, electronics, communications and other fields
-
product
Integration of Inline Test Systems
The test system and adapter can also be integrated in inline test systems. Additional communication can take place via interfaces (e.g. RS232, DLL). We have already created numerous integrations for different manufacturers.
-
product
Integrated Current Sensors
GO series
*Standard package and small footprint*Cost effective*A perfect compromise for small drives, robots, solar inverters, e-bikes etc.
-
product
Integrated Test Facility
ITF
The ITF, located in El Segundo, California, has multiple test stations to enable parallel testing and significantly streamline program test schedules. More than 25,000 square feet are available for integration and test activities, including a 10,000-square-foot Class 10K clean room. Our facilities feature thermal vacuum chambers and test stations to support optical alignment, warm optical bench testing, and hardware integration.
-
product
Value Family 6th Generation Intel® Core™ i7/i5/i3 Processor-Based Fanless Embedded Computer (Code name: Skylake)
MVP-5000 Series
The MVP-5000 Series provides an optimal balance of price and performance in a compact construction. Incorporating 6th Generation IntelR Core? processors, the MVP-5000 features computing performance boosted by up to 30% over previous generation-processors. Integrating the front-mounted industrial I/O and fanless construction featured in ADLINK?s proven Matrix line, and rich LGA 1151 socket type CPU selection, the MVP-5000 Series is ideally suited to a wide variety of machine, factory, logistic automation, and general embedded applications.
-
product
Switches-SP3T
Macom Technology Solutions Holdings Inc.
At MACOM we offer an extensive collection of switches covering multiple commercial and aerospace and defense markets. Our product portfolio has a broad frequency spectrum from DC to 70 GHz. Our silicon Heterolithic Microwave Integrated Circuit (HMIC) PIN diode process is ideal for high power and broadband switches operating from 50 MHz to 26 GHz. Our AlGaAs PIN diode process can extend the upper frequency range of our switch die beyond 70 GHz and is ideal for instrumentation and radar applications. Our GaAs pHEMT and MESFET technology is ideal for fast switching and low control voltage switches optimized for both narrow band and broadband applications. Our 75 Ohm absorptive switches are designed specifically for demanding CATV, FTTx and DBS Infrastructure and CPE applications.
-
product
16 Channel Charge Integrating ADC
CQ16
The CQ16 is a 16-channel 12bit, fast converting charge-integrating ADC for CAMAC. To provide compatibility to older CAMAC ADC’s it can be switched into an 11-bit mode. All data read-out is provided either via CAMAC commands or through the fast FERA bus on the front of the module.
-
-
product
Wireless Billet Scale System
SW888RFX™
Displays Setups to One Hundredth of a Percent! Fully Integrated RFX Wireless Weighing Technology the most widely used advanced weighing technology of its kind and is used by champions in all forms of motorsports.
-
product
Wireless Connectivity Laser Distance Meter
MS-BLDM1130C
Bluetooth Integrated Wireless Connectivity Laser Distance Meter
-
product
SoC Integration At RTL
Before logic synthesis, STAR enables full implementation capabilities towards IP and connectivity insertion with a real-time monitoring of the integration progress. This enables SoC creation in minutes and maximize design reuse from existing projects.
-
product
Class 1 Integrating Sound Level Meter and Advanced Analyzer
HD2110L
HD2110L is an handheld integrating sound level meter performing either spectral or statistical analysis.
-
product
Integrated Gas Alarm & Control System
MCX-32
Teledyne Gas & Flame Detection
The MCX-32 controller features a flexible design that allows the user to customize a system by choosing from a selection of individually addressable field devices or use addressable input and output modules. Detcon’s full range of gas sensors (purchased separately) can be used to create a gas detection system consisting of toxic gas, combustible gas, and/or oxygen deficiency. A wide range of field devices such as liquid level, temperature, pressure, flow, etc., can also be configured for input to the control system. Four standard I/O modules are available: a 4-channel 4-20mA input module (DA-4), a 4-alarm relay output module (RL-4), a 4-channel 4-20mA output module (AO-4), and a 4-relay contact input module (DI-4). I/O modules are din-rail mounted and stackable allowing for seamless system expansion. The I/O modules may be mounted within the main system enclosure or in separate enclosures suitable for the area classification where installation will occur. In many cases using distributed I/O nodes can significantly reduce wiring and installation costs.
-
product
Mission Computer Software Integration Rig
MS 1124
The HSIR is the ground test facility and it simulates various LRUs/sensors interfaced with the HAWK Mission Computer. RIG consists of Industrial computers with Simulation modules, Acquisition modules, Video generator module and video display monitors. RIG provides the simulated inputs to both the MCs from each simulated sensor/ LRU through hardwired signals, through the MIL-1553B, Arinc 429, RS-422, RS232 and Ethernet etc. The rig is capable of testing two MCs together either of which can be used as the Bus Controller (BC) or the Remote Terminal (RT). The rig provides the facility to monitor and acquire the MIL-1553B, Arinc 429, RS-422, and RS232 Ethernet bus, Analog IOs, Synchro IOs, Discrete IOs and transactions that takes place between the MCs and various sensors/units. The RIG has the capability to test individual MCs also.
