Filter Results By:
Products
Applications
Manufacturers
-
product
Volvo Oxygen Sensor
KS60113 - Volvo
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
product
Nuclear Industry Instruments
The Failed Fuel needs accuracy to Identify Leaking Nuclear Fuel in both Pressurized Water Reactors and Boiling Water Reactors in Nuclear Power Plant.
-
product
Distillation Characteristics Tester
K590
Chongqing Kailian Yongrun Industrial Co.,Ltd.
To measure the distillation characteristics of gasoline, aviation gasoline, jet fuel, solvent with special boiling point, naphtha, diesel oil, distillate fuel and similar petroleum products;Conforms to GB/T 6536, ASTM D86.
-
product
Hydraulic & Pneumatic Pressure Sensors
One of the toughest applications for pressure sensors is measuring high pressure, repetitive pulses, such as those encountered in hydraulic applications. However, our pressure sensors are designed to continuously measure repetitive pulses during applications such as hydraulic cylinder “torture” testing or diesel fuel injection. Ordinary diaphragm-type sensors usually fatigue quickly in such applications.
-
product
POWER PROBE 4 MASTER KIT
PPKIT04
*Combines the Power Probe 4, PPECT3000 and various accessories to provide the ultimate combination of diagnostic and circuit testing capabilities*Tests for AC/DC voltage in 100ms and 50s resolutions, AC volts RMS and volts peak-to-peak, measure resistance, frequency and pulse width (negative and positive)*Tests fuel injectors, module drivers (transistors) and works as a circuit detector with the PPECT3000
-
product
fuel Center Products
Secure PCI compliant and easy to install networking solutions for all the data connections in and around your fuel center.
-
product
LPG Mass Flow Rate Detection System
This is a massflow rate measurement system that can measure the massflow rate of LPG with high accuracy using the Coriolis method massflow meter.LPG is a fuel that easily vaporizes, and it is not difficult to measure the correct flow rate in a gas-liquid mixed state.
-
product
Volumetric Flow Detectors
FP-5000 Series
In engine evaluations such as emission mode tests and transient tests for performance evaluation, the evaluation methods have been shifting from steady-state tests to transient tests. In the evaluation of fuel consumption, the requirement for evaluating the fuel consumption characteristics in transient duration has been increasing as well as the total fuel consumption for each mode. The FP-5000 series has achieved high pulse resolution and wide measurement range. It enables to detect changes in the flow rate effectively and responsively, and measure large flow rate. It can be used when the flow rate increases, such as when measuring alcohol fuel.
-
product
Combustion Efficiency Analyzer
CEA-100
Walsn CEA - 100 combustion efficiency analyzer is designed to continuously monitor CO content in flue gas while the measurement data can be used to adjust the ratio of fuel/ air so as to achieve the maximum boiler efficiency for boiler operation. Walsn CEA - 100 adopts the dual-measuring-sensor technology and features high accuracy with low zero drift and very small failure rate, matching the requirements of the harsh industrial environment. It is also easy to install and maintain.
-
product
PEM Fuel Cell Test Stations
Available with Greenlight''s integrated ''Intelligent Fuel Cell Diagnostics'' capabilities:FCDXTMCE certification including optional 3rd party verificationIndustry-leading software and diagnosticsAutomated reformate gas simulation (blending)5 different gas humidification technologies available, including Greenlight''s optional Rapid Response humidification system24/7 unattended operation with Emerald control and automation softwareIndustry leading cell voltage monitoring accuracyUser-adjustable safety featuresFuel cell stack leak testingOptional integrated environmental chambersOptional high temperature configuration, specifically designed for PBI membrane researchOptional DMFC configurationWorldwide service and support
-
product
Industrial ATX Motherboard With 12/13/14th Gen Intel® Core™ I9/i7/i5/i3 Processor
IMB-M47
ADLINK's IMB-M47 ATX Motherboard is a driving force behind industrial automation, supporting 14/13/12th Gen Intel® Core™ processors, and delivering substantial improvements in performance, capacity, and GPU support through its seven PCIe slots, PCIe 5.0 compatibility, DDR5 memory, and 2.5GbE PoE capability. Tailored for a range of industrial applications including automation, machine vision, factory automation, and logistics, the IMB-M47 features up to 128GB DDR5 memory at 4800MHz, supports three independent displays, offers USB 3.2 Gen2x2 (20Gb/s), 3x 2.5GbE LAN, multi-M.2 Key M, TPM 2.0 security, and PCIe 5.0 slots for high-performance add-on cards. Optimized for the latest Intel processors, this motherboard blends efficiency and performance cores, bolstering edge applications with swift memory performance via DDR5 technology. With a commitment to technology leadership, ADLINK equips customers with the tools to harness the latest processors, streamline real-time graphics processing, and fuel innovation in Edge AI applications, solidifying its role in the future of industrial edge computing.
-
product
Grid-Connection Testing System
This system is a power supply test system that performs grid-connection testing of distributed power sources (solar cells, fuel cells, gasoline engines, etc.)Enable inverter device testing that complies with the Agency for Natural Resources and Energy’s “Guidelines for System Interconnect Technical Requirements” and the Japan electrical Safety & Environment Technology Laboratories (JET) publication “Testing Methods for Small Solar Cell Power Generation System and System Interconnection Safety Devices”.
-
product
Fuel Flow Measurement Systems
FQ Series
Measuring a vehicle’s fuel flow requires a precise system which can run stationary and transient tests. It must also be able to offer high reproducibility and run cycle measurements under real operational conditions, including WLTP. Our FQ Series of fuel flow measurement systems offers a highly precise method of measuring various fuel types, and covers the full range from small engines (incl. single-cylinder research engines) up to heavy-duty engines with up to 5000 kW.
-
product
IAC Test Light
3501
Peaceful Thriving Enterprise Co Ltd
For GM1982 and newer GM TBI and PFI fuel infection system with square 4-pin connector. For GM vehicles with throttle body or port fuel injection systems, check the electronic control module signal that provides direction to the idle air control motor.
-
product
Electronic Fuel Quantity Indicator
Proportional to the amount of fuel in the tank, thereby visibly indicating remaining fuel quantity to the pilot.
-
product
Saluki SEL8 Series Programmable DC Electronic Load (up to 200KW)
The new SEL8 series programmable DC electronic load is a new generation product designed by Saluki Technology. Incorporating high-performance chips, the SEL8 series delivers high speed and high accuracy with a resolution of 1mV and 1mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs).SEL8 series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar cell and fuel cell etc. test and measurement applications.* Customization available upon request
-
product
Aviation Engine Test Cells
1.Design, manufacture and installation: ● Thrust stand components: thrust measurement system, adapter, superstructure etc. ● Facility subsystems: DAQ, supply systems (fuel, oil) etc.2.Civil construction works: site survey, building works etc.3.Contracting: ● Turn-key – MERA is able to supply a “turn-key” test cell including civil works, thrust stand, DAQ, all necessary facility subsystems, specialized software, throttle control level and etc. ● Joint – MERA is capable to supply specified items such as thrust stand with DAQ and software. The Customer is able to procure necessary items such as test nacelle directly from OEM. 4.Project management in accordance to EPC (Engineering, Procurement, Construction, FIDIC) 5.Certification in accordance to international and local standards and rules (SAE 5305) Engine types: PD-14, PS-90, RD-93, RD-33MK, AL-31FN
-
product
Flow Detector with Pressure Loss Compensation Function
FP-213S / FP-2140S
The Volumetric Flow Detector FP-213S, FP-2140S are volumetric flow detectors, used in combination with the Digital Flow Meter FM/DF series, for precision measurement of fuel flow such as gasoline, light oil and kerosene.They are suitable for those who want to evaluate the engine performance by measuring the minute flow rate of a small engine and making the fuel supply pressure as close as possible to the actual vehicle state.
-
product
Indirect Sequential Injection
The ECU is designed to exploit the chemical-physical characteristics of the gas fuel used in Otto engines while maintaining the level of emissions of the exhaust gas according to the original standard car.The connector used in Air 48 is automotive type 48- Poles . The connection to the engine signals , offers exceptional qualities of connective security and protection against water infiltration .
-
product
Management System
CHANGSHA KAIYUAN INSTRUMENTS CO., LTD.
Monitors all systems from receiving sample to consumption, including coal truck, coal yard and equipment of sampling, sample preparation and analysis for fuel.
-
product
Saluki SEL7 Series Programmable DC Electronic Load (up to 6kW)
The new SEL7 series programmable DC electronic load is a new generation product designed by Saluki Technology. Incorporating high-performance chips, the SEL7 series delivers high speed and high accuracy with a resolution of 0.1mV and 0.01mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs).SEL7 series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar cell and fuel cell etc. test and measurement applications.
-
product
Automotive Audio Bus (A2B®)
Analog Devices Automotive Audio Bus (A2B®) technology provides critical support to the vehicle infotainment systems of tomorrow. Our A2B products deliver high fidelity audio while increasing fuel efficiency, thanks to upward of 75% less cabling weight. The A2B portfolio helps enables multiple applications such as voice recognition and active noise cancellation. A2B is a single-master, multiple-slave system where the transceiver chip at the host controller is the master.
-
product
Oxidation Stability & Cold Flow Properties
These Anton Paar instruments enable you to evaluate the oxidation stability as well as the storage and thermal stability of mineral oil products or oil and fat containing cosmetics and food samples. The gum content tester is available for tests on the gum content of fuels and other volatile distillates. Cold flow properties (cold filter plugging point and cloud and pour point) show the lowest temperature for a trouble-free operation of diesel fuel or heating oil.
-
product
LAMBDA METER
LA4
This stand-alone device has a wide measuring range for determining lambda, A/F ratio, and oxygen content. The sensor's short heating time results in fast measuring response. The measuring system reacts quickly to exhaust gas modifications. The device offers analog output of the physical value (parameter setting), as well as a download of characteristic curves for specific fuels.
-
product
Automatic Acid Value Tester
HTYSZ-H / 684
Wuhan Huatian Electric Power Automation Co., Ltd.
It is suitable for detection transformer oil, turbine oil and anti - fuel oil.
-
product
Fuel/Other Analyzers
Our products are used to test fuel in a couple of ways. Fuel blending is the process of ensuring a fuel has the desired composition in terms of relative concentration of components. Testing fuel for contamination ensures that the equipment that burns the fuel will not suffer damage from impurities in the fuel.
-
product
Class I, Division 2 Solution
Class I, Division 2 remote I/Os, such as CID1 monitors and CID2 solutions, have met the requirements of hazardous area computer such as explosion proof, oil field drilling, pump station monitoring, chemical plants, pharmaceutical factories, oil pipeline monitoring, tank storage monitoring, and fuel station management. Class 1, Div 2 remote I/O products include data acquisition modules, industrial Ethernet switches, serial device servers, industrial monitors and embedded automation computers, all.
-
product
Alfa Romeo Oxygen Sensor
KS60113 - Alfa Romeo
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
product
Turbine Flow Meters
CT300, CT400
Flows up to 400 lpm (100 US gpm)Pressure up to 420 bar (6000 psi)Choice of 4-20mA and 0-5V outputs2-3 top ports as std for temperature / pressureBSP or SAE inlet / output portsFor use with oils, fuels, phosphate-estersBi-directional
-
product
Fuel Cell Test Software
Exceptional functionality with a user-friendly graphical interface- Enhanced with our proprietary automation language, Emerald Software - Comprehensively manages the full range of FCATS fuel cell test system parameters- Simple user-friendly interface permits even novices to begin testing in minutes
