Filter Results By:
Products
Applications
Manufacturers
-
product
Analog to Digital Converter
high-linearity, ultra-low power, dual-channel, 12-bit, 50-MSPS to 160-MSPS, analog-to-digital converter (ADC) family. The devices are designed specifically to support demanding, high input frequency signals with large dynamic range requirements. A clock input divider allows more flexibility for system clock architecture design and the SYSREF input
-
product
mmWave and Microwave GaAs Frequency Dividers and Prescalers
Keysight Technologies provides MMIC frequency dividers and prescalers ideal for high-frequency communications, microwave instrumentation, and electronic warfare (EW) radar system applications. These devices operate from DC to 16 GHz and provide a large input power sensitivity window and low phase noise.
-
product
350 MHz DDS Signal Generator
425A
The 425A generates sine, LVDS and LVCMOS outputs simultaneously and is programmable in 10µHz steps from 250kHz to 350MHz and includes an LVCMOS Prescaler and Divider for generating LVCMOS frequencies down to 2 Hz. The 425A is controlled by an RS232 serial interface. Phase can be programmed with 14-bit resolution. The Frequency is accurate to 1.5ppm when using the on board TCXO timebase or you can use an external timebase. It requires 5 VDC power. A Line Voltage AC Adapter is included. SOF8_425 windows software is also included.
-
product
MLDD 8-Way Power Dividers
KRYTAR MLDD 8-way power dividers lend themselves to emerging wireless ultra-broadband designs and many test and measurement applications. KRYTAR’s power dividers offer the widest frequency coverage in a single package on the market and provides superior performance. Targeting broadband electronic warfare (EW) systems and complex switch-matrix applications, for example, KRYTAR has used its proprietary design to produce a wide assortment of matched-line directional dividers (MLDD) with ultra-high performance over a broadband frequency range. Our 8-way power dividers can also be manufactured to meet military specifications.
-
product
IP67 DC Blocking L-Band Splitter
PD5031
INSTOCK Wireless Components, Inc
PD5031 is an IP67 outdoor, weather resistant, DC blocking, three way, RF broadband, 50 ohm, power divider, power combiner furnished with N type coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other ports blocking DC. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5031 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 3 way power divider input rating tables for additional power handling info.
-
product
Comb Generators
Keysight comb generators provide excellent phase and amplitude flatness making them ideal for use in phase calibration applications. A customer selectable USB-controlled frequency divider which allows for broad range of input signal frequencies from 10 MHz to 67 GHz and small minimum tone spacing of 10 MHz, makes Keysight comb generators suitable for characterizing non-linear devices.
-
product
DC Blocking L-Band Splitter Combiner
PD5960
INSTOCK Wireless Components, Inc
PD5960 is an IP67 outdoor, weather resistant, DC blocking, six way, RF broadband, 50 ohm, power divider, power combiner furnished with TNC coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other ports blocking DC. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5960 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 6 way power divider input rating tables for additional power handling info.
-
product
4-Way Power Dividers From 0.5 To 60 GHz
Pulsar Microwave's 4-way power dividers are available in narrowband and broadband configurations, covering frequencies from 500 MHz to 60 GHz. They are designed to handle from 10 to 30 watts input power in a 50-ohm transmission system. Microstrip or stripline designs are utilized, and optimized for best performance.Units come standard with SMA or N female connectors, or 2.92mm, 2.40mm, and 1.85mm connectors for high frequency components.
-
product
DC Blocking L-Band Splitter Combiner
PD5920
INSTOCK Wireless Components, Inc
PD5920 is an IP67 outdoor, weather resistant, DC blocking, two way, RF broadband, 50 ohm, power divider, power combiner furnished with TNC coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other port blocking DC. Max voltage rating at the DC blocked port is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5920 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 2 way power divider input rating tables for additional power handling info.
-
product
IP67 DC Blocking L-Band Splitter
PD5141
INSTOCK Wireless Components, Inc
PD5141 is an IP67 outdoor, weather resistant, DC blocking, four way, RF broadband, 50 ohm, power divider, power combiner furnished with SMA coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other ports blocking DC. Max voltage rating at the DC blocked port is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5131 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 4 way power divider input rating tables for additional power handling info.
-
product
Integrated Passive Devices
Macom Technology Solutions Holdings Inc.
MACOM’s new Integrated Passive Devices (IPD) products can be used in a wide range of aerospace and defense, wireless, and test and measurement applications. These IPD devices implement various functions such as baluns, couplers and power dividers, and are available in PQFN or bare die. Operating over the 2 GHz to 20 GHz frequency range our IPD products offer excellent performance over wide bandwidths.
-
product
IP67 DC Blocking L-Band Splitter
PD5131
INSTOCK Wireless Components, Inc
PD5131 is an IP67 outdoor, weather resistant, DC blocking, three way, RF broadband, 50 ohm, power divider, power combiner furnished with SMA coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other ports blocking DC. Max voltage rating at the DC blocked port is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5131 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 3 way power divider input rating tables for additional power handling info.
-
product
IP67 DC Blocking L-Band Splitter
PD5121
INSTOCK Wireless Components, Inc
PD5121 is an IP67 outdoor, weather resistant, DC blocking, two way, RF broadband, 50 ohm, power divider, power combiner furnished with SMA coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other port blocking DC. Max voltage rating at the DC blocked port is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5121 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 2 way power divider input rating tables for additional power handling info.
-
product
RF Frequency Divider, Multiplier, & Detector Modules
Analog Devices’ broad portfolio of frequency dividers, multipliers, and detector modules offers a number of high performance solutions, with features such as ultralow phase noise and improved frequency lock time to meet the demands of modern technology. Explore our product lines and discover how they can meet your industry, market, and design needs.
-
product
Two Channel Phase and Amplitude Noise Analyzer
DCNTS -190
The DCNTS is a two channel Phase and Amplitude noise analyzer. Its dual demodulator architecture allows the system to use cross-correlation to cancel its internal noise and limitation; it is like comparing the outputs of 2 systems and only display the similarities while rejecting differences. Its main extension is the Residual Noise measurement front-end which includes all necessary hardware to automatically measure residual noise on 2-ports devices either in RF frequencies or microwave. It could be a frequency multiplier or divider, an amplifier or any other phase coherent input to output device.
-
product
Frequency Divider
Trig-TekTM 313A
Divide high frequency to a lower frequency with an exact integer division with 1-digit divisor increments from 1 to 9999
-
product
Magic Tee
MHTXE
The MHTXE Magic Tee Hybrid Couplers for millimeter waves are matched power dividers for variety of applications (general purpose power splitters, power combiners, phase measurement circuits, phase / frequency discriminators). The MHTXE Magic Tee Hybrid Couplers are available in waveguide bands between 33 and 170 GHz. These couplers are four-port transmission line components with a port configuration as shown in figure. Operation bandwidth is limited to 20÷90% waveguide operation frequency range depending on performance specifications.
-
product
DC Blocking L-Band Splitter Combiner
PD5940
INSTOCK Wireless Components, Inc
PD5940 is an IP67 outdoor, weather resistant, DC blocking, four way, RF broadband, 50 ohm, power divider, power combiner furnished with TNC coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other ports blocking DC. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5940 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 4 way power divider input rating tables for additional power handling info.
-
product
Combiners and Dividers
CAES Combiners and Dividers are available in a variety of models from 1:2 – 1:N combiner/divider splits. Generally designed as Wilkinson structures, these are used to combine or divide power within a given designed frequency range.
-
product
High Impedance Differential Clock Divider
Alliance Support Partners, Inc.
he ASP-DCD-00 board is a high impedance input clock divider circuit. It is designed to provide minimum load to a clock source for frequency measurement. It accept single ended (Unbalanced) or differential (Balanced) signals with amplitudes as little as 100mV rms; it divides the input signal frequency from 2 to 256 times depending on shunt jumper selections on J3. The board requires 5VDC 500mA power source to operate. The output is capable of driving 5V TTL logic levels.
-
product
RF Microwave Components
Specialized in passive RF microwave components, Radiall develops and manufactures a wide range of coaxial microwave components including terminations, attenuators, couplers, power dividers, filters and other specialized components. Our range covers a wide frequency spectrum from DC to 50 GHz, as well as low to high power, designed specifically for military, instrumentation, telecom and aerospace applications.
-
product
IP67 DC Blocking Splitter Combiner
PD5123
INSTOCK Wireless Components, Inc
PD5123 is an IP67 outdoor, weather resistant, DC blocking, two way, RF broadband, 50 ohm, power divider, power combiner furnished with SMA type coaxial connectors. The passive Wilkinson design passes RF and the 10 MHz reference signal through both ports while blocking DC current. This configuration is typically used in combining applications to prevent passing DC to the sum and adjacent ports. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5123 is a bidirectional device capable of 40 W max microwave input power levels in both power splitter and combiner apps. See 2 way power divider input rating tables for additional power handling info.
-
product
IP67 DC Blocking Splitter Combiner
PD5033
INSTOCK Wireless Components, Inc
PD5033 is an IP67 outdoor, weather resistant, DC blocking, three way, RF broadband, 50 ohm, power divider, power combiner furnished with N type coaxial connectors. The passive Wilkinson design passes RF and the 10 MHz reference signal through both ports while blocking DC current. This configuration is typically used in combining applications to prevent passing DC to the sum and adjacent ports. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5033 is a bidirectional device capable of 40 W max microwave input power levels in both power splitter and combiner apps. See 3 way power divider input rating tables for additional power handling info.
-
product
Frequency Dividers
SMA SPDT electro mechanical RF relay switch features Indicators, Failsafe, Normally Open with an isolation minimum of 60 dB. SPDT electromechanical relay radio frequency switch PE71S6052 is part of over 40,000 RF, microwave and millimeter wave components available from Pasternack. Our SPDT SMA coaxial RF relay electromechanical switch can ship worldwide the same day that it is bought as with our other available RF parts.
-
product
Low Frequency 3-Way Power Dividers To 1500 MHz
Pulsar Microwave manufactures 3-way power dividers from 1 MHz to 1.5 GHz in both surface mount and connectorized packages. They are rated for an input power of 1 watt maximum for a load VSWR of 1.20:1 or better. This series of 3-way power dividers are currently offered in four outline packages. The hermetically sealed outline 301 and surface mount outline B are useful in portable applications where space is premium. Outlines 412 and 433 are connectorized versions in cross or in-line format, respectively.
-
product
Image Reject Mixers To 16 GHz
Image Reject Mixers incorporate a 2-way 0° divider, two 90° hybrids and two mixers. They produce an IF signal when driven by an LO and RF signal while rejecting unwanted sidebands that are very close in frequency.
-
product
Power Dividers
We currently offer coaxial resistive power dividers (aka power splitters), which are inherently broadband and have excellent low frequency response (0!) albeit with poor isolation; and also Wilkinson Power dividers, aka Wilkinson Splitters. We have as connector options SMA, N, 1.95mm, & 2.92mm. Our power dividers cover DC-70Ghz. While most of our power dividers are 2-ways, we also have 3, 4, & 8 way dividers. The resistive power splitters are implemented with tiny resistors. Wilkinson splitters can be microstrip or stripline. RF Power Dividers are often lumped element, Microwave Power Dividers are often microstrip.
-
product
Power Divider
Chengdu KeyLink Microwave Technology Co., Ltd.
The series of products are passive devices.The frequency range covered by 0.5GHz~40GHz.The products have the characteristics of good amplitude and phase consistency and low insertion loss.The products can be applied to all kinds of receiving and transmitting channels. KeyLink's power dividers can be categorized as follows.
-
product
Instrument Transformer
CT & PT Test Equipment
Measurements International Ltd.
Calibration of Voltage and Current Transformers from a Single Instrument, Calibration of Instrument Transformers with Different Rated Ratios Using One Single Reference Standard, Calibration of Voltage Transformers (VT) up to 800 kV When Used with MI 2500 Series of HV Dividers and Standard Capacitors, Calibration of Current Transformers (CT) Up to 10000 A When Used With MI 7020 and/or 7200 Series of Precision Current Transformers and/or Current Comparators, Test Frequency from 15 Hz to 100 Hz70.
-
product
Passive Components
Ducommun millimeter wave products include various passive components including multi-hole directional couplers (PCM), crossguide couplers (PCC), magic tees (PCT), coax power dividers (PPD), bandpass, low pass and high pass filters (PFB, PFL and PFH), waveguide diplexers (PDC), waveguide transitions (PRC and PTW), waveguide to coax adapters (PTC) and waveguide components (PWS, PWE, PWH, PWM and PWT). These passive components cover frequency range from 8.2 to 110 GHz and feature high performance and low cost.
