Filter Results By:
Products
Applications
Manufacturers
Cages
-
product
Connector Block, 50-Pin D-Type, Female
40-965A-050-F
The 40-965A-050-F connector block provides a simple method of connecting to 50-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross-sectional area and insulation properties. Connector blocks have higher losses than a cable connection and the breakdown voltage is controlled by clearances to the metal shell. The metal shell includes an internal insulation barrier under the carrier board.
-
product
50-Pin D-Type Male Connector Block
92-965-050-M
This connector block provides a simple method of connecting to 50-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross-sectional area and insulation properties.
-
product
200-Pin LFH Connector Block, Female
B200LFR-2F-5B
Suitable for use on the front of PXI modules this connector block provides a simple method of connecting to high density 200-Pin LFH connectors. The screw terminals use a rising cage screw clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross sectional area and insulation properties.
-
product
9-Pin D-Type Connector Block
92-965-009-M
This connector block provides a simple method of connecting to 9-Pin D-Type connectors. The screw terminals use a rising cage screw clamp mechanism to minimize risk of copper strand breakage.
-
product
78-Pin D-Type Block Without Backshell
92-965-078-F
This connector block provides a simple method of connecting to 78-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross-sectional area and insulation properties.
-
product
VME Test Extender 6U/220mm 64X with P0
116EXT6122-0125R
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
200-Pin LFH PCI Connector Block, Male
50-965-200-M
Suitable for use on the front of PCI modules this connector block provides a simple method of connecting to high density 200-Pin LFH connectors. The screw terminals use a rising cage screw clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross sectional area and insulation properties.
-
product
96-Pin Micro-D Connector Block, Female With Screwlocks
40-965-096-F
This connector block provides a simple method of connecting to 96-Pin SCSI Style Micro-D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
product
37-Pin D-Type Male Connector Block
40-965-037-M
Suitable for use on the front of modules this connector block provides a simple method of connecting to 37-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
product
Cabinet Style Steri-Dry™ Lab Sterilizer
The Gruenberg Steri-Dry™ Dry Heat Lab Animal Science Sterilizer provides the animal care market with equipment to sterilize animal habitat cages through the process of dry heat sterilization. These dry heat sterilizers are designed and built for lab animal science applications.
-
product
DC Coreless Motor
Adamant Namiki Precision Jewel Co Ltd.
There is a structure in the cage shape by only the copper wire turns around a cylindrical permanent magnet placed inside It is a feature. There There is not an anron core, it does not receive the action of the copper basket type rotor is light, the moment of inertia becomes small, so quick response is possible. A Permanent Magnet, There Is No Cogging, That Is, Rotation Is Smooth, And Vibration And Noise Can Be Reduced. - Since Rare Earth Magnets With High Magnetic Properties Are Used And The Rotor Is Formed Only With Coils, The Motor Itself Can Be Made smaller and lighter.
-
product
Type 12R2, 14U, 19" Rackmount, MIL-Rugged, Vertical
12R2-14U-V
The 14U, 12R2 was designed to meet the harsh environment of shipboard, airborne, and ground mobile applications per MIL-STDs.Shock isolated versions are designed to attenuate 25G shock to the chassis to less than 10Gs at the card cage and PSU tray.
-
product
160-Pin DIN41612 Connector Block, Female
92-965-160-F
This connector block provides a simple method of connecting to high density DIN41612 connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage.
-
product
Computer controlled tabletop tensile test stand 95TM - 30" travel
95TM
The ComTouch controller reports current reading, force results, test stand direction, limit switch warnings, test stand speed, and error messages. Designed to be rugged, sturdy, and easy-to-use, this test stand is built to last. Just select from our wide line of fixtures for standard tensile testing or install an optional compression cage for testing in compression.
-
product
High-Speed Optical Delay Line
The Peregrine Optical Delay Line (1-cm, 60 ps delay) and the Gyrfalcon Optical Delay Line (2-cm, 120 ps) are high-speed, high precision, voice coil motor optical delay lines. They have zero-backlash and no hysteresis. Both have similar form factors that are compatible with 30-mm cage components and 1.035” – 40 threads. Both include full digital and analog control and include a USB interface.
-
product
Type 12R2, 8U, 19" Rackmount, MIL-Rugged, Vertical
12R2-8U-V
The 8U, 12R2 is designed to meet the harsh environment of shipboard, airborne, and ground mobile applications per MIL-STDs. Shock isolated versions are designed to attenuate 25G shock inputs to the chassis to less than 10Gs at the card cage.
-
product
Faraday Cages
LBA's EMFaraCage® faraday cages are EMI and RFI shielding boxes and RF test enclosures that bring convenience to device testing. Faraday cages are ideal for isolating critical systems in high field RF environments or wherever RF ingress or egress must be minimized. Security, production testing, biomedical research and semiconductor testing are only a few of the many areas where EMFaraCage® faraday shielded enclosures are employed. EMFaraCage® faraday cage enclosure systems are fully featured to support a wide variety of test missions. The standard faraday cages include effective power, dataline and RF signal isolation in large test volumes. EMFaraCage® faraday cages are much more affordable than shielded room solutions and offer the convenience of portability.
-
product
Animal Temperature Controller - Low Voltage
TCAT-2LV
Our TCAT-2 family of general purpose PID Autotuning Controllers provides accurate temperature control in a variety of laboratory applications. Combined with a heat lamp or heating pad, the TCAT-2 may be used to maintain the body temperature of anesthetized animals during surgery or stereotaxic procedures. Small animal cages are easily warmed with a heat lamp. The TCAT-2 may also be used in cooling applications, such as to control independent perfusate cooling systems. Realizing that laboratory applications are diverse, Physitemp can provide several versions of the TCAT Controller. The model specified depends on whether a laboratory has a general or specific need for the controller
-
product
Analog Input Module, 12-bit A/D
IP320A
The IP320A monitors 20 differential or 40 single-ended input channels. When used with a carrier that holds four IP modules, up to 160 inputs can be obtained from a single card cage slot.
-
product
Connector Block, 78-Pin D-Type, Male
40-965A-078-M
The 40-965A-078-M connector block provides a simple method of connecting to 78-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximize copper cross-sectional area and insulation properties.
-
product
VME Test Extender 6U/220mm Universal
110EXT6122-000X
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
Low Voltage DC / Battery Powered High Voltage Amplifiers
WMA-005 And WMA-005LF
The Falco Systems WMA-005 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-005LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
product
96-Pin Micro-D Connector Block, Female DIN Rail Mounted
40-966-096-F
Suitable for mounting on DIN Rails this connector block provides a simple method of connecting to 96-Pin SCSI Style Micro-D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
product
Compact PCI Cards And Cages
We offer a wide variety of CompactPCI (cPCI) digital I/O cards, and card cages with robust and reliable design intended for use in factory automation and process control applications. The CompactPCI form factor allows for easy integration of the cards into cPCI style racks.
-
product
VME Test Extender 3U/400mm Universal
110EXT3140-10xx
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
VME Test Extender 3U/220mm J2
111EXT3122-12XX
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
EMF Measurements/EM Measurements/Electromagnetic Radiation
Holland Shielding Systems B.V.
Electromagnetic fields cause interference in electronic devices and may affect the health of people close to where the fields are generated. It is important to recognize this at an early stage in a construction process, for instance at a future construction location or while construction is already underway, so that budgets are not exceeded. By means of field-strength measurements one can chart the existing electromagnetic fields and radiation emitted by GSM, UMTS antennas and transformer spaces, to mention a few examples. These measurements can help determine the best location in the new building for rooms where sensitive measurements are to take place, e.g. in hospitals or nano laboratories. And last but not least, field-strength measurements can detect sources of interference and can be part of a scheduled check of existing screened spaces and Faraday cages.
-
product
Crowbar Resistors
Crowbar resistors are three phase resistance banks which are connected to the rotor windings of the DFIG (Doubly-Feed Induction Generator) such as wind power generator. They are used to prevent damage to the inverter circuits attached to rotor side when a fault occurs in the grid. DFIG power converter, which has a restricted over-current limit, needs special attention during faults in the grid. If the rotor current or DC link voltage reaches the threshold value, crowbar resistors disconnect the converter in order to prevent the generator turning into a squirrel cage induction machine. By crowbar resistors, the DFIG could stay connected to the grid and continue its operation.
-
product
VXS Type 32V, w/plug in PSU
32V05LY348Y3VGE0
VXS Type 32V family of enclosures provide a lightweight, tower platform for packaging portable VITA System applications. Designed to VITA & IEEE. Systems can be configured with or without rear I/O card cage.
-
product
Faraday Cage
Electrostatic noise from the laboratory environment disturbs measurement signals and decreases data quality drastically for small current signals. Our Faraday Cage enables effective shielding for measurement on high impedance or low current samples.
