Filter Results By:
Products
Applications
Manufacturers
Broadband Seismometers
measure motion over a broad range of frequencies.
See Also: Seismometers, Seismographs
-
product
Seismometers
3 Series
The Güralp 3T is the ultimate and original triaxial, broadband, weak-motion seismometer that provides exceptionally high quality monitoring over the long-period.
-
product
Broadband Seismometer
KS-2000M / KS-2000BH
*1000 V/(m/sec) sensitivity (other sensitivities on special order). Three-component. 120 s to 50 Hz (other cut-off values possible). The Geotech Model KS-2000 is a new broadband seismometer based on the time proven Model KS-54000. Its small dimensions make it ideal for portable applications.
-
product
Seismometers
3ESPC Series
The Güralp 3ESPC is a proven weak-motion triaxial broadband seismometer for the price and size of a medium-motion instrument.Ideally suited for long-term temporary and permanent installations in areas with low to moderate noise levels. The instruments' broadband response and low self-noise level make it suitable for seismic monitoring at all scales: local, regional and teleseismic.
-
product
Very Broadband Seismometer
KS-54000/KS-1
Geotech's Model KS-54000 is a borehole, Model KS-1 a vault, three-component seismometer, designed for ultra low-noise monitoring for frequencies from 0.003 to 5 Hz, being below the Low Noise Model for frequencies up to 5 Hz.
-
product
Radian Posthole and Borehole
High performance sub-surface broadband seismometer with maximum versatility and operational at any angle. The Güralp Radian is a triaxial, force-feedback, broadband, digital seismometer designed for posthole and borehole deployments.
-
product
Seismometers
3T-120 Pothole
120 s to 50 Hz frequency response (option to 100 Hz), 1500 V/ms-1 (2 x 750 V/ms-1) sensitivity, Covers the complete seismic spectrum with a single transfer function, Measured Self noise below the USGS NLNM from 166 s (0.006 Hz), remaining below the high frequency limit of the NLNM at 10 Hz, High linearity: >111 dB (USGS figures), Dynamic range of 167 dB at 1 Hz (Full octave width across 1 Hz), Cross axis rejection over 65 dB; sensor axes orthogonal to within ±0.05°, Remote, automatic electronic mass locking, unlocking and centring, Operating tilt range of ±5° with adjustable feet for off-horizontal installation bases, Low power consumption: 0.75 W from a 10–36 V supply, Stainless steel enclosure, 100 bar / 10 MPa waterproof connector, IP68 - protection against effects of permanent immersion under pressure to 350 m depth
-
product
Seismometers
SI value, the so called “velocity response spectrum”, is one of the standards to express an earthquake''s destructive power against structures. SW-74SI is an advanced model equipped with alarm output to 10-step and SI value output.
-
product
Seismometers
3T-360
A high-performance, observatory grade seismometer, suitable for monitoring the very long period with a 360 s to 50 Hz frequency response (option to 100 Hz)
-
product
Broadband
NC346 Series
Noisecom's NC346 Series is designed for Broadband coaxial noise figure measurement applications. Each module's low VSWR reduces reflections and increases measurement accuracy.
-
product
Broadband Diagnostics
TruVizion
TruVizion gives you a comprehensive view into the health of your cable or DSL network, including up to 90 days of historical data.PreEqualization Analyzer lets you quickly find upstream impairments like reverse splitters, loose or corroded connectors and bad wiring. Plus, you can be proactive and actually fix those problems before they affect service for your subscribers.RF Inspector is an inexpensive app that can do what a meter can do, except it can do it on a tablet from wherever you happen to have Internet access. That means in the office, at home, or in the field.Upstream Analyzer shows you the RF signals for all ports and modems on your Cisco CMTS without any additional equipment, cabling or connectors, and yes, you can see ingress under the carrier with one click.
-
product
Seismometer
4211
This seismograph model has been developed for the purpose of fast deployment and installation, for engineering structures seismic control, for application in areas with constant background noise above NLNM level.
-
product
Broadband
The UNH-IOL is the industry's leader in testing broadband systems and equipment. Working closely with service providers, equipment manufacturers, and the Broadband Forum, we have spent the last 15 years developing extensive testing coverage for DSL, GPON, TR-069, and IPv6. Our broadband testing can help ensure your products and services meet your customers' expectations with the highest quality possible.
-
product
Ocean Bottom Seismometers
Tried and tested on successful deployments all around the globe, ours is the most comprehensive range of cabled and portable ocean bottom instruments available.
-
product
Broadband Amplifier
BBA150
The R&S®BBA150 broadband amplifier family generates power in the frequency range from 4 kHz to 6 GHz. The compact amplifiers are rugged and feature high availability.
-
product
Broadband Power Amplifier
Panda Microwave design, manufacture, and support a wide variety of Power Amplifier. RF amplifiers product line from Panda Microwave consists of low noise amplifiers, Power Amplifier Module and Solid State High Power Amplifier. Our Power amplifiers cover frequency range from 100MHz to 50GHz and used Thin-film Technology. Our low noise amplifiers have superior noise figure numbers and a variety of models. Gain block low noise amplifiers provide all around gain where noise is not critical. High power amplifiers system equipment is available with either manual or digital control interfaces, power capacities up to 100W pulse power.
-
product
Broadband Amplifier
BBL200
The R&S®BBL200 broadband amplifiers are ideal for applications requiring high RF power.
-
product
48-Channel Seismometer
FlashSeis48
ZZ Resistivity Imaging Pty. Ltd.
48 channel seismic data acquisition system.
-
product
Broadband RF/Microwave Power Amplifier
R&K wideband power amplifiers support a wide range of applications with their broadband characteristic.
-
product
Broadband Power Amplifier
PAS-08042-60
* Solid State Power Amplifier* Small Signal Gain: 60 dB typ.* Rack Mount Case* Internal Cooling Fans*Type N Connectors* Over-voltage, over-current protections
-
product
Broadband Power Amplifier
PAS-08025-200
* Solid State Power Amplifier* Small Signal Gain: 50 dB typ.* Rack Mount Case (Optional)* Internal Cooling Fans* Type N Connectors
-
product
Connect Broadband Access Controller
CBAC
Evolve your fiber network with an open software solution that facilitates faster product innovation cycles, increased automation, and deeper network visibility.
-
-
product
Broadband Amplifiers
Blonder Tongue Laboratories, Inc.
Blonder Tongue offers a variety of RF amplifiers for broadband CATV or OTA (over-the-air) applications. Be it a 1GHz power doubling two-way indoor distribution amplifier or a mast-mounted preamplifier, or anything in between, we have you covered.
-
product
Broadband Tuners
BT1500A
The BT1500A 1500 watt balanced antenna tuner is the only 1500 Watt, Double-L Network antenna tuner on the market today covering 20m to 160m (2500+/-j2500) and 10m - 15m (1000+/-j1000). The BT1500A features two tandem mounted, precision ceramic roller inductors for a truly balanced tuner.
-
product
Broadband Dielectric Spectroscopy
Material Sensing & Instrumentation
Broadband Dielectric Spectroscopy is a powerful tool for investigating a variety of dielectric processes for both electrical and non-electrical applications. Also called Impedance Spectroscopy, the measurement separates molecular process on the basis of response time, providing a unique relaxation frequency along with a signature variation with frequency.
-
product
Broadband Current Probes
Conducted currents can be measured without making direct contact with the source conductor or metallic surface by means of clamp-on broadband current probes. The BCP-5xx EMC Current Probes are designed to permit field intensity meters, spectrum analyzers, and other 50W impedance instruments to measure quantitative magnitudes of current.
-
product
Broadband Calibrated Noise Sources
Fairview Microwave’s calibrated noise sources cover frequency bands from 10 KHz to 18 GHz. Their performance specifications include output ENR levels ranging from 15 dB to 30 dB and typical VSWR levels as low as 1.25:1. Depending on the model, calibrated frequency points are at 10 MHz, 100 MHz, 1000 MHz, 2000 MHz and 1 GHz steps. The temperature coefficient of these noise sources is < 0.01 dB/°C and noise output variation is < 0.1 dB/%V.
-
product
Short-period Seismometer
S-13J
The S-13J is a 1.0 Hz short-period sensor that is ideal for portable applications which require exceptional performance in a small size.
-
product
Broadband Coaxial Noise Sources
Our integrated noise modules contain all the required biasing circuitry and only need a positive voltage to activate for an easy installation. Since they typically do not contain amplification, the raw noise output from the diode is seen at the output of the module resulting in a maximum ENR of approximately 35dB. Primary applications include system built-in test and laboratory use.
-
product
5-Watt Broadband Transmitter
Loc3 5W
The 5-Watt broadband transmitter has selectable induction and direct connection frequencies from 98Hz to 200kHz, SD mode (Signal Direction), fault find and true resistance measurement up to 1 Mohm. The two inch by one-inch dot matrix display with LED backlight shows output current, connection type, volts, resistance, frequency, volume, battery condition and high voltage warnings.
