Filter Results By:
Products
Applications
Manufacturers
Board Test Fixtures
jigs which hold, align and engage pcb with test interconnect.
See Also: Fixtures, Test Fixtures, Bare board Fixtures, PCB Test Fixtures, Genrad Fixtures
-
product
Board Test Fixture Probes
Offering a wide range of standard spring contact probes to meet your testing requirements and has long been recognized as the world’s largest probe manufacturer. With over 60 different probe series ranging from 0.02" (0.51 mm) to 0.187" (4.75 mm) pitch with multiple length, travel, ICT, lead free and rotator options, we provide a full portfolio designed for general purpose test on bare boards, loaded printed circuit boards and surface mount assemblies.
-
product
6 Sided Bed of Nails Testers
BoxProber Family
6 sided Bed of Nails circuit board test fixture. Probes top bottom and all 4 sides. Central camming mechanism pull plates inward. Mechanically or electrically actuated options. Designed primarily for testing products in plastics. Side access electrically probes outside panel connectors. The unit will also optically read LEDs and key segments off LCD displays. Solenoids will press buttons and servos will turn selector switches. DC motors are used to adjust multiple turn potentiometers. Microphone will detect audio output tones. Top and bottom of circuit boards can also be probed if removable access panels are available. This unit will also probe all 6 sides of a circuit board. This is typically utilized in applications where connector testing is required.
-
product
80 DIOs, 8AIs, 8AOs JTAG Boundary Scan Resources Unit Expansion
YAV9JTAH
80 DIOs8 Ais8 AOsCompatible with all JTAG vendors
-
product
Faraday Chamber for RF w/Exchangeable Cassettes 340x350mm RCV 9025 for 6TL36
AN133
The Faraday Chamber is an add-on for the 6TL36 test handler. This kit is installed into the 6TL36 in the same way a normal test fixture would be installed, being the only difference the fact that different products to be tested will, from that moment on, only need an additional exchangeable cassettes to be tested.
-
product
ATE Self Test Fixtures
AL663
AL663 fixtures include all the electronic parts required to perform an effective test platform diagnostic. The AQ818 device allows to perform a series of tests, obtaining a report of the faulty instruments or switch modules and also a report about the relay contacts estimated life.
-
product
Interactive Benchtop Test
Strict time-to-market deadlines make it vital to efficiently debug and validate product designs. Virtual instrumentation provides a unified interface that gives engineers an advantage over traditional box instruments.
-
product
Wireless Test Standards Software
Generate and analyze signals for cellular and connectivity standards with NI PXI RF instrumentationPerform advanced automated test with the easy-to-use NI-RFmx software APISave on all NI RF wireless test software under a single license
-
product
EFT Module for Teststand
The Electronics Functional Test (EFT) Module for TestStand provides out-of-the-box tools to speed up development of automated tests for electronic assemblies including PCBAs, subassemblies and final assemblies. Test engineers can develop, deploy and execute test sequences quickly and efficiently with minimal custom code development for a shorter time-to-solution.
-
product
Test Workflow Pro
Test Workflow equips engineers with application-specific tools so that they can choose the right one for the job—from graphical programing environments to no-code and interactive software applications. Engineers can use Test Workflow software to perform quick ad-hoc tests, build an automated test system, automate data analysis and reporting, develop test sequences, and more.
-
product
Functional Test Fixtures
Reliable connections to device under test (DUT) test points are essential for robust functional test. Bloomy provides rugged fixtures and cable sets (ITAs) built for thousands and thousands of cycles in manufacturing environments. With the industry’s best mass interconnects and internal electronic keying, our fixtures are easy to change out and are automatically recognized by the test system.
-
product
Fixture Self-Test Controller and Calibration Check
AQ818
The module AQ818 includes all the electronic blocks required to perform an effective test platform self-test. Thanks to this module, a chain of tests can be performed, which will end up not only with a report of the defective instruments or switch modules, but also with the relay contacts live expectancy report.
-
product
34945EXT Distribution Board, For Two 87222, L7222C Transfer Switches And Six N181x SPDT Switches
Y1154A
The Y1150A-Y1155A distribution boards enable simple connections to the external switches. The distribution boards plug onto the 34945EXT and are used to route the power and control signals from the driver module to the switches using standard cables.
-
product
Electronic Control Unit Functional Test
End-of-line tests are critical to ensure passenger safety in the era of smarter vehicles. A flexible test solution is needed to ensure extensive test coverage and high test throughput with a low total cost of ownership.
-
product
In-Circuit Test System Calibrations
Regular calibration is essential to ensure accuracy and reliability in testing. Forwessun offers precise calibration services tailored to your test systems, verifying that all components meet industry standards. Our calibration services maintain peak accuracy and compliance, so you can be confident in your system’s performance for any testing application. Choose from one-off calibrations or scheduled service contracts to meet your needs.- HP3070 - Agilent- Keysight - GenRad- Teradyne
-
product
Motion Control Terminal Board For Panasonic Minas A Servo
DIN-814PA
- Motion control terminal board with 100-pin SCSI -II cable- On-board connector type: 100-pin SCSI-II female- Suitable for Panasonic Minas A servo- Shipped with 1-meter ACL-10250 cable- Available for PCI-8134, PCI-8164 and PCI-8158- Dimensions: 123 mm x 107 mm x 44 mm (WxLxH)
-
product
Photodiode Burn-in Reliability Test System
58606
The Chroma 58606 PD/APD Burn-in system is a high density, multifunction and temperature controlled module based system for photo diode burn-in and lifetime test. Each module has up to 256 Source Measurement Unit channels which can source current and measure voltage in various scenarios such as one described below. The system can accommodate 7 modules for a total of 1,792 device channels.
-
-
product
Noise Figure Analysis Using NI PXI RF Test Instruments
NI-RFmx Noise Figure
Measure noise figure, gain, Y-factor, effective temperatures, hot and cold power, and moreOptimized calibration and measurement routines for multi-DUT test using Y-factor and cold sourceSupports the PXIe-5668R 26.5 GHz VSA, the PXIe-5698 26.5 GHz preamplifier, and VSTsDesigned for use with industry-standard noise sources such as the Noisecom NC346 Series
-
product
Wafer-Level Parametric Test
Wafer-level reliability engineers need to reduce test time without sacrificing measurement quality and accuracy.
-
product
SoC Test Systems
Specifically designed for high-throughput and high parallel test capabilities to provide the most cost-effective solution for fabless, IDM and testing houses. With the full functions of test capability, high accuracy, powerful software tools and excellent reliability, 3650-EX is ideal for testing consumer devices, high-performance microcontrollers, analog devices and SoC devices.
-
product
Terminal Board For General Purpose With 100-Pin SCSI-II Connector
DIN-814-GP
- Available for PCI-8134, PCI-8164, PCI-8154, PCI-8158 and PXI-8164- Supports Specific Servos by Cable Selecting- On-board Connector Type: 100-pin SCSI-II- Dimensions: 146 mm x 85 mm x 44 mm (W x L x H)
-
product
PCIe 5.0 Test Platform
PXP-500A
The Teledyne LeCroy PXP-500A Test Platform provides a convenient means for testing PCIe 5.0 cards with a self-contained portable and powered passive backplane. The PXP-500A provides power required for both cards under test.
-
product
TD-SCDMA Analysis Using NI PXI RF Test Instruments
NI-RFmx TD-SCDMA
The NI-RFmx TD-SCDMA personality is a highly optimized API for performing physical layer measurements on TD-SCDMA cellular standard signals. NI-RFmx TD-SCDMA is completely interoperable with all NI-RFmx APIs. It provides simple access to the most advanced optimization techniques such as multi-measurement parallelism and multi-DUT measurements. The result is extremely fast and high-quality measurements with minimal software development efforts.
-
product
NI HIL and Real-Time Test Software Suite
Suites combine LabVIEW Professional Development System with NI's most popular application softwareIncludes LabVIEW Professional, VeriStand, and the LabVIEW Real-Time and LabVIEW FPGA modulesEach new suite includes a one-year NI Training and Certification membershipSoftware is shipped on USB 3.0 media with NI device drivers included to speed up your installationConfigure real-time test applications quickly and easily; add custom functionality
-
product
NI Automated Test Software Suite
The NI Automated Test Software Suite features all three NI IDEs and NI's most popular application software and add-ons specifically for building your automated test system with confidence. This package offers the power of LabVIEW, LabWindows/CVI, and Measurement Studio combined with the TestStand ready-to-run, test executive and the Switch Executive intelligent switch management application
-
product
Test Platforms
Leverage 20+ Years of Test Industry Experience with Built-In IP for Maximum Reuse
-
product
6U CompactPCI Dual 64-bit PMC Slots Carrier Board
cPCI-8602
- Supports two single-size 32,64-bit/33,66 MHz PMC sites in 4HP width- PICMG® 2.0 32,64-bit/33,66 MHz cPCI bus- PICMG® 2.1 Hot Swap Specification Compliant- 3.3V or 5V V(I/O) for cPCI bus and PMC sites- PLX® PCI-to PCI bridge PCI6154 for PCI bus- Power and HotSwap LED incidators on front panel
-
product
Regenerative Battery Pack Test System
17020
Chroma's 17020 is a high precision system specifically designed for secondary battery modules and pack tests. Accurate sources and measurements ensure the test quality that is suitable to perform repetitive and reliable tests that are crucial for battery modules / packs, for both incoming or outgoing inspections as well as capacity, performance, production and qualification testing. Chroma's 17020 system architecture offers regenerative discharge designed to recycle the electric energy sourced by the battery module ei ther back to the channel s in the sys tem performing a charging function or to the utility mains in the most energy efficient manner. This feature saves electricity, reduces the facilities thermal foot print and provides a green solution by reducing the environmental impact on our planet. Chroma's 17020 system is equipped with multiple independent channels to support dedicated charge / discharge tests, on multiple battery modules / packs, each with discrete test characteristics. The channels can easily be paralleled to support higher current requirements. This feature provides the ultimate flexibility between high channel count and high current testing.
-
product
NI's Wireless Connectivity Functional Test Solution
The proliferation of wireless functionality in electronic devices is pressuring test developers to deliver more complex testers within shrinking project schedules. Evolving standards and the integration of multiple wireless technologies into new product designs mean developers must prioritize measurement speed and quality to maintain throughput and yield targets. For a solution to meet these sorts of demands, it must:
-
product
Electronics Functional Test
Functional test for productive manufacturing. Manufacturers of products enabled by electronics must assure proper operation prior to shipment. Bloomy’s line of universal test systems are ideal for functional test of your PCBAs and subassemblies, from the simplest to the most complex. The UTS family of products combines high-performance test instruments, switching, power control and mass-interconnect hardware with our robust UTS software suite into a low-risk, cost-effective and powerful test solution for your device under test (DUT).
