Filter Results By:
Products
Applications
Manufacturers
-
product
622 HP Eddy Current Chassis Dynamometer
CM-51-EC
Weight Capacity: 25,000 lb (11,340 kg) per axleRoll Brakes: pneumatically-actuated discShipping Weight: 8,340 lb (3,783 kg)Capacity: 622 hp at 45 mph (464 kW at 72 kph)Rolls: 20 by 36 in. (508 by 915 mm) long4 front fixed rolls, 2 rear rolls fixed toaccommodate axle spreads from48 to 60 in. (1,219 to 1,524 mm)tandem centersPit Required Depth: 25 in. (635 mm)
-
product
Axle Damping Test
MSD 3000 | VP 215033
Maschinenbau Haldenwang GmbH & Co. KG.
The axle damping test stand MSD 3000 is characterized by a quick and precise physical check of the axle damping. The frequency-controlled plate excitation by means of electric motors determines the maximum oscillation amplitude and then evaluates the axle damping according to the principle of Lehr's damping. The fully automatic test sequence including the determination of the axle and vehicle weight enables a time-saving and reliable assessment of the axle damping.
-
product
Axle Damping Test Bench
C_MSD C 13.0 W220 | VP 215050
Maschinenbau Haldenwang GmbH & Co. KG.
The axle damping test bench C_MSD is characterised by a fast and precise mechanical testing of the axle damping. Through the frequency-controlled plate activation via electric motors, the maximum vibration amplitude is calculated and then the axle damping is evaluated according to the Lehr damping principle. The fully automatic test sequence, including the calculation of axle and vehicle weight, saves time and allows a reliable assessment of the axle damping.
-
product
Four-Wheel Drive Dingle Roller Dynanometer for Cars with Axle Load of up to 2.4T, for Installation in an Existing LPS 3000 Dynanometer
MSR 500/2 CAR 4WD (LPS 3000) | VP 230038
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/2 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/2 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.The MSR 500/2 CAR 4WD is suitable for installation in an existing LPS 3000 base.
-
product
Wheel Play Detectors
A play detector consists of two plate units on which the wheels of an axle are placed. The plates are moved horizontally in an oscillating fashion by hydraulic cylinders. This movement can be done in different directions. In this way an inspector in the inspection pit can easily check for play on the different components underneath the vehicle. To make it even easier, the remote control unit to start and stop the plate movement has a built-in lamp.
-
product
Vehicle Weighing
Avoid ends for excessive load or poorly distributed in trailers or trucks, the portable axle weighing system is the right option for you.
-
product
Axle Damping Test Bench
C_MSD C 2.5 W250 | VP 215049
Maschinenbau Haldenwang GmbH & Co. KG.
The axle damping test bench C_MSD is characterised by a fast and precise mechanical testing of the axle damping. Through the frequency-controlled plate activation via electric motors, the maximum vibration amplitude is calculated and then the axle damping is evaluated according to the Lehr damping principle. The fully automatic test sequence, including the calculation of axle and vehicle weight, saves time and allows a reliable assessment of the axle damping.
-
product
General Purpose Reaction Dual Shaft Torque Sensor
STS SERIES
The STS Series is our general purpose reaction type shaft torque sensor. They are often installed between devices such as motors, switches, shafts or axles, and their mounting plate to provide bi-directional torque output. They are available in six capacity ranges from 600 in-lb through 12,000 in-lb, and are made from 17-4ph heat treated stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
product
Towing Dynamometer
RS-80K
RS-80K towing dynamometer is designed for testing Class B trucks and is the most full-featured, reliable and accurate towing dynamometer in the industry. The RS-80K is built with a heavy duty steel frame, heavy-duty industrial axles and rides on an air ride suspension. The RS-80K is designed to maintain 80,000 Newtons of constant drawbar pull and the ability to simulate an uphill slope of 25%. The towing dyno uses absorbers with special high temperature coils powered by an industrial generator so there are no lead-acidbatteries to charge and testing is unlimited at low speeds.
-
product
Digital Roller Brake Tester for Cars and Vans up to 4.0 T Axle Load with 2 x 4 kW Drive Motors and Max. Track Width of 2,200mm
C_MBT C 4.0 W220 STOCK | VP 210165
Maschinenbau Haldenwang GmbH & Co. KG.
Digital roller brake tester for cars and vans up to 4.0 t axle load with 2 x 4 kW drive motors and a max. track width of 2,200 mm.Basic version - available ex stockincl. specific option package.Particularly suitable as stand-alone tester or as part of car reception and diagnostic test lanes.
-
product
Acceleration Simulation Mode (ASM) Roller Set
ASM-P | VP 230046
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-P roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. The increased tractive force of its eddy current brake means that the ASM-P is also suitable for power measurements at constant speed and constant tractive force.
-
product
MBT 3000 Series
Maschinenbau Haldenwang GmbH & Co. KG.
Roller-Brake-Tester up to 8000 kg axle load
-
product
4WD Roller Set
ASM-BF/2 | VP 230044
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-BF/2 4WD roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. The ASM-BF/2 4WD is built into the base.
-
product
Instrumentation/Electronics
Junction Boxes for 4 or 8 load cells in ABS, Aluminium or Stainless Steel (optionally with ATEX approval)Intelligent Junction Box for individual monitoring of load cell performance and error checking of up to 4 load cellsSimple weighing transmitters (with analogue output for connection to a PLC) or high speed transmitters with built-in weight indication, external communications, set points and dedicated check weigher functionsPurpose designed weight indicators with external communications, ATEX approval for use in hazardous areas and IP69K protection for use in harsh, wash-down environmentsDedicated weighing controllers for batching, filling, check weighing, truck weighing and axle weighing, with communications and relay outputsInstrumentation/electronics with Weights and Measures approvals (legal-for-trade), i.e. OIML R76 and EN45501:2015 (NAWI)Remote displays for secondary weight indication at a different locationLoad cell tester with intelligent diagnosticsLoad cell simulator
-
product
Speed-O-Calibrator
16470
The Speed-O-Calibrator consists of two sections, control box and drive unit. The control box is stored inside the drive unit for easy portability. The control box weighs less than 6 lbs and is used in the cab of a locomotive to control the speed of the Axle Alternator Drive Unit. The Drive Unit drives the Axle Alternator at various speeds while the user verifies that the correct speed is displayed in the cab. The test system provides a complete test of the speedometer system, including all types and paddle lengths of Axle Alternators.
-
product
Dynanometer Roller Set
FPS 2700 | VP 230048
Maschinenbau Haldenwang GmbH & Co. KG.
The FPS 2700 roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. As a result of the increased tractive force of its eddy current brake, the FPS 2700 is additionally suitable for power measurements at constant speed and constant tractive force.
-
product
Shock Absorber Tester
Maschinenbau Haldenwang GmbH & Co. KG.
Display on LON analog displays with theEvaluation in "Lehr''s damping factor" or damping ratio "D"Fully automatic testAutomatic test start after bilateral plate load of more than 60kgFrequency controlled drive excitation by electric motors to determine the maximum vibration amplitude with subsequent evaluation of the axle dampingrunning underbody as self-supporting frame constructionParallelogram guided test plates, thus no fixed wheel contact requiredgalvanized version
-
product
Towing Dynamometer
RS-200K
RS-200K towing dynamometer is designed for testing Class A trucks and is the most full-featured, reliable and accurate towing dynamometer in the industry. The RS-200K is built with a heavy-duty steel frame, heavy-duty industrial axles and rides on an air ride suspension. The RS-200K is designed to maintain 200,000 Newtons of constant drawbar pull and the ability to simulate an uphill slope of 25%. The towing dyno uses absorbers with special high temperature coils powered by an industrial generator so there are nolead-acid batteries to charge and testing is unlimited at low speeds.
-
product
XCITE 1300T Torsional Series
The Xcite 1300T Torsional Series of modal exciters provides pure torque input into structures for modal parameter estimation without the bending mode coupling effects present when linear excitation is applied through moment arms. These systems are used in structure borne noise tests of structures such as automotive and truck transmissions, prop shafts, axles, differentials, and torsional engine dampers.
-
product
Towing Dynos for Medium-Duty Trucks and Buses
Designed to maintain 8,992 to 17,985 lb (40,000 to 80,000 N) of constant drawbar pull, our towing dynamometers for medium-duty trucks and buses feature rugged steel frame, heavy-duty axles and air ride suspension, dampened drawbar system and wireless touchscreen controller. Plus, with special absorbers powered by an industrial generator, there are no lead-acid batteries to charge.
-
product
Tachometer Tester
Maschinenbau Haldenwang GmbH & Co. KG.
for motorcycles, for cars and vans up to 4000 kg and for cars and trucks up to 13000 kg axle load.
-
product
Digital Roller Brake Tester for Cars and Vans up wot 3.5 T Axle Load with 2 x 3 kW Drive Motors and Max. Track Width of 2,200 mm
C_MBT C 3.5 W220 | VP 210152
Maschinenbau Haldenwang GmbH & Co. KG.
Digital roller brake tester for cars and vans up to 3.5 t axle load with 2 x 3 kW drive motors and a max. track width of 2,200 mm.Particularly suitable as stand-alone tester or as part of car reception and diagnostic test lanes.
-
product
Single-Axle Single Roller Dynanometer for Cars with Axle Load of up to 2.4T
MSR 500/1 CAR | VP 230035
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/1 single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/1 CAR guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.
-
product
Wheel Running Tester up to 15000 kg axle load
MINC II EURO | VP 420005
Maschinenbau Haldenwang GmbH & Co. KG.
The test lane-compatible MINC II EURO guarantees a verification of the axle geometry in seconds when the test vehicle drives over (up to 15.0 t axle load) as well as a fully automatic evaluation of the deviation in m / km. The measured values are displayed either in analog form on a dial or by transmission to a PC screen (including graphic representation).
-
product
Electric Axle Testing
Our E-Axle testing systems are developed for the performance, endurance, and production testing of electric axle drives.
-
product
Towing Dynamometer
RS-125K
RS-125K towing dynamometer is designed for testing Class A trucks and is the most full-featured, reliable and accurate towing dynamometer in the industry. The RS-125K is built with a heavy-duty steel frame, heavy-duty industrial axles and rides on an air ride suspension. The RS-125K is designed to maintain 125,000 Newtons of constant drawbar pull and the ability to simulate an uphill slope of 25%. The towing dyno uses absorbers with special high temperature coils powered by an industrial generator so there are no lead-acid batteries to charge and testing is unlimited at low speeds
-
product
Axle Load Simulators
In case vehicles need to perform a brake test in laden condition, one could consider to use a load simulator. In that case the vehicles can come to the brake test unladen; the load simulator will add the required load to the axles.
-
product
Axle Damping Test Bench
C_MSD C 2.5 W220 | VP 215047
Maschinenbau Haldenwang GmbH & Co. KG.
The axle damping test bench C_MSD is characterised by a fast and precise mechanical testing of the axle damping. Through the frequency-controlled plate activation via electric motors, the maximum vibration amplitude is calculated and then the axle damping is evaluated according to the Lehr damping principle. The fully automatic test sequence, including the calculation of axle and vehicle weight, saves time and allows a reliable assessment of the axle damping.
-
product
Vibration Testers
Application for vibration tester: used for measuring periodic motion, to check the imbalance and deflecting of moving machinery.Is pecifically designed for present measuring various mechanical vibration. So as to provide the data for the quality control, run time and equipment upkeep.use the high-performance acceleration meter, realize the repetitiveness and accurate measurement. it has the function of testing axle bearing situation
-
product
Roller Brake Testers for Max. 5000 kg Axle Weight
The VLT roller brake testers perform very accurate, reliable and fast measurements. All roller brake testers comply with the highest standards and are of high quality. There is a perfect roller brake tester for every garage or workshop. VLT roller brake testers achieve the lowest cost of ownership because of their longevity. They are available for a wide range of vehicles; from motorcycles to cars and lorries.
