Filter Results By:
Products
Applications
Manufacturers
-
product
Board
Arduino Leonardo with Headers
The Arduino Leonardo is a microcontroller board based on the ATmega32u4 (datasheet). It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs), a 16 MHz crystal oscillator, a micro USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.
-
product
ST VL6180X Time of Flight Sensor
SEN-36001
Highly integrated breakout board for the ST Micro VL6180X Time of Flight (ToF) range finder sensor. This sensor has many uses in the robotics, cell phone and gesture recognition space. It has two programmable GPIO pins, and most importantly, measures absolute distance up to 100mm. The SEN-36001 includes a VL6180X IC centered between two 4-40 sized mounting holes with onboard 2.8V LDO and voltage translation to handle interface voltages from 3V to 5V. The board is interfaced via an I2C interface and all IC pins have been broken out to a 0.1" pin header. Example code for the Arduino platform is available below and includes code for both the proximity measurement and ambient light sensing capabilities.
-
product
Shield
Arduino 4 Relays Shield
The Arduino 4 Relays Shield is a solution for driving high power loads that cannot be controlled by Arduino's digital IOs, due to the current and voltage limits of the controller. The Shield features four relays, each relay provides 2 pole changeover contacts (NO and NC); in order to increase the current limit of each output the 2 changeover contacts have been put in parallel. Four LEDs indicate the on/off state of each relay.
-
product
SparkFun Current Sensor Breakout
ACS723
The SparkFun Current Sensor Breakout is a high accuracy board that utilizes the ACS723 for moderate AC and DC current sensing applications. The ACS723 sensor uses a Hall effect sensor to output a voltage relative to the current flowing through the IP+ and IP- pins on the board. The advantage of using a Hall effect sensor, specifically, is that the circuit being sensed and the circuit reading the sensor are electrically isolated meaning that, although your Arduino is running on 5V, the sensed circuit can be operating at higher DC or AC voltages!
-
product
Bi-Directional Level Translator
IFB-10001
Easily connect Arduino or other 5V microcontrollers to ~3.3V sensors. Based on the TI TXB0108 auto-sensing, bi-directional level translator, this module provides access to all 8 channels of the TXB0108 and has a built-in 300mA LDO with 200mV max dropout voltage at full load. Regulated 3.3V output allows this single board to both interface withandpower 3.3V sensors. An important feature of this module is the ability to operate SPI and other digital lines (not including I2C) at high-speed, whereas the 'NXP level shifter' maxes out at 400kHz and resistor dividers fail much earlier. The TXB0108, integrated with the LP3981 LDO, provide a fast, reliable solution to mismatched interface voltages that exceeds the performance of other solutions.
-
product
Shield
Arduino MKR Mem Shield
Are you developing a complex IoT device with your MKR board and running out of memory? Add Flash memory and microSD storage to your MKR board, and allow over-the-air updates, with the Arduino MKR MEM Shield.
-
product
Board
Arduino MKR1000 WIFI
Arduino MKR1000 is a powerful board that combines the functionality of the Zero and the Wi-Fi Shield. It is the ideal solution for makers wanting to design IoT projects with minimal previous experience in networking.
-
product
Programmable 70W Electronic Load
MightyWatt R3
The All-New MightyWatt revision 3 turns your Arduino Uno R3 or Arduino Zero (M0/M0 Pro) into an electronic load capable of dissipating 70 Watts in a very small form factor. Ideal for testing power supplies, batteries, solar cells, fuel cells or power amplifiers. MightyWatt R3 has a research-grade electronics and is aimed not only at hobbyists but also at professionals.
-
product
Arduino Shield Header Kit
INT-19002
Complete header set for Arduino Uno shields. Contains: 1 1x6, 2 1x8, 1 1x10, and 1 2x3 header. These headers have square pins and fit into standard 0.1" breadboards. Gold plated and RoHS compliant.
-
product
Tiny AVR Programmer
The ATtiny45 and 85 are a couple of really cool little MCUs but did you know you can program them in Arduino? That's right, now you can shrink your Arduino projects down to "tiny size" by moving your code straight over to these small but capable ICs. The standard method for programming the ATtiny ICs involves a breadboard, lots of jumper wires and a hardware programmer, but David Mellis over at MIT Media Lab has simplified the process by laying out this handy USB programmer.
-
product
Shield
Arduino Motor Shield Rev3
The Arduino Motor Shield is based on the L298 (datasheet), which is a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors. It lets you drive two DC motors with your Arduino board, controlling the speed and direction of each one independently. You can also measure the motor current absorption of each motor, among other features. The shield is TinkerKit compatible, which means you can quickly create projects by plugging TinkerKit modules to the board.
-
product
NITlab Chassis Manager Card Arduino
The latest NITOS Chassis Manager Card is designed to add remote management capabilities of the NITOS nodes. CM Card consists of an Arduino Ethernet Microcontroller and a NITOS CM Card Shield. The CM Card's Firmware is a tiny web-server, that receives and processes http requests.
-
product
RISC-V Processor IP Core Evaluation Kit
The EMSA5 demo platform is an ideal tool for evaluating the RISC-V processor IP core EMSA5. It contains an Artix®-7 35T FPGA Arty evaluation board with implemented EMSA5-IP core. Thanks to the included peripherals and expansion interfaces, the kit is ideal for numerous applications. The kit is JTAG programmable and includes Quad SPI Flash, a JTAG port, 10/100 Mb/s Ethernet and a USB-UART bridge, four Pmod connectors and an Arduino Shield expansion connector.
-
product
Infrared Receiver For Parallax Small Robots
350-00039
Infrared receiver with 38 kHz carrier frequency, for use as a replacement part with the following small robot kits:*BASIC Stamp Boe-Bot*Robot Shield Kit for Arduino*Propeller ActivityBot*cyber:bot for micro:bit
-
product
Board
Arduino Mega 2560 Rev3
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Mega 2560 board is compatible with most shields designed for the Uno and the former boards Duemilanove or Diecimila.
-
product
SparkFun FTDI Basic Breakout
Beefy 3
This is SparkFun Beefy 3 FTDI Basic Breakout for the FTDI FT231X USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards. It can also be used for general serial applications. Built upon the same foundation as our 3.3V SparkFun FTDI Basic Breakout, the Beefy 3 is equipped with an AP2112K voltage regulator making this FTDI basic breakout board capable of handling a current load of up to 600 mA! With the addition of a more "Beefy" voltage regulator your will now be able to power a 3.3V project directly from the FTDI. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards.
-
product
TI HDC1080 Humidity and Temperature Sensor Breakout Board
SEN-37001
Breakout board for the Texas Instruments HDC1080. This sensor is an extremely accurate temperature and humidity sensing device, with +/-0.2C temperature and +/-2% humidity accuracy typical. These specs far exceed the accuracy of ICs that came before it, including the HTU2x and SHT2x series, and improves upon the success of the HDC1050. In addition, the HDC1080 has a wide input voltage range of 3V-5V and includes temperature and airflow cutouts as recommended for the best operation. Finally, in the case of environmental changes that could cause light condensation, the HDC1080 has a built-in heater to burn off any condensate. Example code (Arduino platform) is available below.
-
product
MAX31855 K-Type Thermocouple Arduino Shield
SEN-30004-K47
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino. The MAX31855K supports a measured temperature range of -270C-1372C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega
-
product
Arduino CAN Shield
IFB-10003-INP
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
product
MAX31855 T-Type Thermocouple Arduino Shield
SEN-30004-T03
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino.Each order comes with one board and a set of four female, long extension, headers that can be soldered to the board. If stacking two of these modules on top of each other, please order both a Ch 0-3 and a Ch 4-7 board, as well as an additional set of headers for stacking. We're working on sourcing even longer headers, but the ones currently available are not long enough to stack as-is (they need to be double-stacked).The MAX31855T supports a measured temperature range of -270C-400C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or MegaNote: we also offer a universal version of this board in a smaller for factor, the SEN-30003-T.FeaturesType-specific, miniature-sized vertical thermocouple connectors (vertical flat blades, see pics)Measures four (4) thermocouple channels, full extended range.Boards are stackable. Up to 8 thermocouple channels may be connected to an Arduino.14-bit SPI interfacePlugs directly into an Arduino Uno or Mega form factor with built-in voltage level translation on-board.Standard Arduino female headers required for easy configuration, one set included with order (1-6x1, 2-8x1, 1-10x1 0.1" female stackable headers), not soldered on.Detects shorts to GND or VccDetects open thermocoupleOther versions available (K, J, and T stocked). Contact Customer Service to place a custom order.Mounting holes for 4-40 sized screwsConnections are spaced for 0.1" pin headerDesigned, manufactured, tested and shipped from the USA The MAX31855T supports a measured temperature range of -270C-400C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega
-
product
SparkFun I2C DAC Breakout
MCP4725
You've always wanted to output analog voltages from a microcontroller, the MCP4725 is the DAC that will let you do it! The MCP4725 is an I2C controlled Digital-to-Analog converter (DAC). A DAC allows you to send analog signal, such as a sine wave, from a digital source, such as the I2C interface on the Arduino microcontroller. Digital to analog converters are great for sound generation, musical instruments, and many other creative projects!
-
product
Board
Arduino Zero
Arduino Zero is a simple and powerful 32-bit extension of the platform established by the UNO. This board aims to provide a platform for innovative projects in smart IoT devices, wearable technology, high-tech automation, crazy robotics, and much more.
-
product
MAX31856 Thermocouple Sensor Arduino Shield
SEN-30007-ST
Quad channel thermocouple Arduino shield based on the MAX31856 universal digital thermocouple interface IC. This is an exciting update of the MAX31855, with improvements in resolution (19 vs 14 bits), on-board temperature reference (6 vs 4 bits), and compensation (fully compensated vs nonlinear correction required). The MAX31856 is interfaced via 4-wire SPI with options for interrupt triggering. An LDO and a high-speed level shifter are included on ALL device pins to allow interfacing with to any Arduino - both 3.3V and 5.0V variants - without sacrificing device performance in any operating condition.
-
product
Industrial-Grade Intelligent Analog & Digital Interface Modular Control Box With Arduino Compatibility
I-Pi OT2IT
Discover the freedom of open-source innovation with ADLINK's industrial-grade I-Pi Arduino-Compatible PLC. Say goodbye to restrictive proprietary systems and embrace the vast, versatile world of the Arduino ecosystem. Accelerate your project's journey from concept to commercialization across diverse automation and control tasks. All this, while ensuring steadfast reliability, professional-grade functionality and industry-ready performance.I-Pi-OT2IT is equipped with numerous analog and digital sensors to manage different OT devices in smart factories. It features 8x Digital inputs, 11x Digital outputs, 9x Analog inputs, and 2x Analog outputs, and can be easily controlled by Computer-on-Modules via software over Ethernet/LAN. By consolidating OT with IT, it is the ideal solution to transform your factory into a smart one.
-
product
LTE US Version - 4G, Cat.1, GNSS Tracker
Wio LTE
Wio Tracker (Wireless Input Output) is an open source gateway which enable faster IoT GPS solutions. It is Arduino and Grove compatible development boards that helps you track nearly any moving thing on the planet and then upload that data wirelessly. The Wio LTE is the LTE version of Wio Tracker, so now we’ve got 2 versions of Wio Tracker and the LTE (4G) version will make some differences.
-
product
Classic Family
In the Classic Family, you will find boards such as the legendary Arduino UNO and other classics such as the Leonardo & Micro. These boards are considered the backbone of the Arduino project, and has been a success for many years (and more to come).
-
product
Board
Arduino Uno Rev3
The Arduino UNO is the best board to get started with electronics and coding. If this is your first experience tinkering with the platform, the UNO is the most robust board you can start playing with. The UNO is the most used and documented board of the whole Arduino family.
-
product
Arduino CAN Shield
IFB-10003-ANP
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
product
Shield
Arduino MKR RGB Shield
Write messages and add graphics with this shield. A ready to use library with examples and methods is available for use to easily write static and scrollable text. You can use this shield to show values from your board and is controllable from the Arduino IoT cloud. No need of solder, or special adapters, just plug the RGB matrix shield on top of your favourite MKR board and you are ready to go!
-
product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K0
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
