Filter Results By:
Products
Applications
Manufacturers
Analog Output Modules
-
product
Modbus Analog Output Modules
DAT3020 Series
The DAT3020 series from Datexel is a range of Modbus analog output cards. These cards or modules have both voltage and current outputs either 0-10V or 4-20mA and are isolated from the input, output and power supply. They are available with either 2, 4 or 8 channels. The DAT3011 is a Modbus slave with 2 analog inputs (Thermocouple, RTD's mA, Resistance, Potentiometers, mV and voltage) and 2 analog outputs(4-20mA). It also has 3 digital inputs and outputs. Combining these analog output cards with the analog input cards, and the digital IO cards with the DAT9000 controllers make Datexel the smart choice where Data Acquisition is needed.
-
product
Analog Output Modules
D3000/4000
The DGH D3000/4000 series are complete computer-to analog output modules. They communicate, in ASCII, with RS-232 and RS-485 serial ports. Simple ASCII commands are used to control a 12-bit DAC (Digital-to-Analog Converter) which is scaled to commonly used current and voltage ranges.
-
product
PXI-6713, 12-Bit, 8-Channel, 1 MS/s PXI Analog Output Module
777795-01
12-Bit, 8-Channel, 1 MS/s PXI Analog Output Module—The PXI‑6713 is a high-speed analog output device designed to deliver simultaneous, multichannel updates for control and waveform output applications, such as stimulus-response, power supply control, high-speed, deterministic control, and sensor/signal simulation. In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PXI‑6713 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
product
Analog I/O module with 8 differential analog output channels
IO108
This I/O module is a dedicated analog output module with a resolution of 16 bits. Each of the 8 output channel has its dedicated D/A converter with an update time of 2.2µs. The output coupling of the module can either be ordered as differential or single-ended. Furthermore, several of these modules can be interconnected by trigger lines to synchronously update analog output channels among the different modules.
-
product
PXI Analog Output/Current Loop Simulator Module - 16 Channel
41-765-001
The 41/43-765-001 is a PXI/PXIe 16-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
product
I/O Analog Module with 32 single-ended analog output channels
IO110 I/O
This I/O module is a dedicated analog output module with a resolution of 16 bits. Each of the 32 output channel has its dedicated D/A converter with an update time of 3µs. The output coupling of the module is single-ended for all channels. The output range of each channel can be selected individually.
-
product
NI-9269, 100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module
781098-02
100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module - The NI‑9269 is a channel‑to‑channel isolated analog output module. The NI‑9269 adds channel‑to‑channel isolation for increased safety and improved signal quality. Channel‑to‑channel isolation is commonly needed for applications that have multiple electrical systems, such as automotive tests, or industrial applications that are subjected to increased noise and often contain multiple ground planes.
-
product
PXI-6723, 13-Bit, 32-Channel, 800 kS/s PXI Analog Output Module
778998-01
13-Bit, 32-Channel, 800 kS/s PXI Analog Output Module—The PXI‑6723 delivers low-cost, high-density analog outputs to meet a wide range of applications, such as stimulus-response, signal simulation, waveform generation, and actuator stimulation. In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PXI‑6723 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
product
PXI-6722, 13-Bit, 8-Channel, 800 kS/s PXI Analog Output Module
778999-01
13-Bit, 8-Channel, 800 kS/s PXI Analog Output Module—The PXI‑6722 is a high-speed analog output device designed to deliver simultaneous, multichannel updates for control and waveform output applications, such as stimulus-response, power supply control, high-speed, deterministic control, and sensor/signal simulation. In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PXI‑6722 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
product
PXI/PXIe Analog Output/Current Loop Simulator Module - 4 Channel
43-765-004
The 41/43-765-004 is an 4-channel Analog Output Module designed to meet the requirements of industrial control applications utilising current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signalling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
product
Analog I/O module with 16 differential analog output channels
IO107
This I/O module is a dedicated analog output module with a resolution of 16 bits. Each of the 16 output channel has its dedicated D/A converter with an update time of 2.2µs. The output coupling of the module can either be ordered as differential or single-ended. Furthermore, several of these modules can be interconnected by trigger lines to synchronously update analog output channels among the different modules.
-
product
NI-9264, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module
780927-01
25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module - The NI‑9264 is a simultaneously updating analog output module that accommodates higher‑channel‑count systems. Higher density modules conserve chassis space, which leaves room for other measurement types. Each channel has its own digital‑to‑analog converter. The spring-terminal version of the NI‑9264 uses a 36‑position connector for the output channels, and each channel has a ground connection.
-
product
8/16-CH 16-Bit Analog Output Modules
cPCI-6208/6216 Series
- PICMG 2.0 Rev 2.1- 16-bit D/A resolution- 16-CH voltage on 6216V- 8-CH voltage outputs on 6208A and 6208V- 8-CH current outputs on 6208A- Bipolar analog output range- 4-CH TTL DI and 4-CH TTL DO- Rear I/O available
-
product
PXIe-4322, 16-Bit, 8-Channel, 250 kS/s Ch-Ch Isolated PXIe Analog Output Module
782878-01
16-Bit, 8-Channel, 250 kS/s Ch-Ch Isolated PXIe Analog Output Module—The PXIe‑4322 is a channel‑to‑channel isolated analog output module with integrated signal conditioning. The device provides accurate, simultaneous dynamic voltage and current outputs. By combining signal conditioning and D/A converters on the same device, the PXIe‑4322 isolated analog output module delivers a smaller footprint and higher measurement performance. In current mode, the module operates in all four quadrants, so you can both sink and source current. Isolation and higher voltage and current outputs make this module ideal for automotive applications.
-
product
Analog I/O Module with 16 single-ended analog output channels
IO111
This I/O module is a dedicated analog output module with a resolution of 16 bits. Each of the 16 output channel has its dedicated D/A converter with an update time of 3µs. The output coupling of the module is single-ended for all channels. The output range of each channel can be selected individually.
-
product
Analog Output Module, 16-bit
IP235A
IP235A modules have a 16-bit D/A converter (DAC) to provide highly-accurate analog voltage outputs. An internal RAM buffer enhances control over the transfer of data to the DAC.
-
product
PXI Analog Output/Current Loop Simulator Module - 12 Channel
41-765-002
The 41/43-765-002 is a 12-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
product
PXI Analog Output/Current Loop Simulator Module - 8 Channel
41-765-003
The 41/43-765-003 is an 8-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
product
Analog Output Module, 16-bit D/A
IP231
The IP231 outputs analog voltage signals to drive up to 16 devices. When used with a carrier that holds four IP modules, up to 64 voltage outputs can be obtained from a single card cage slot.
-
product
PXI-6733, 16-Bit, 8-Channel, 1 MS/s PXI Analog Output Module
778512-01
16-Bit, 8-Channel, 1 MS/s PXI Analog Output Module—The PXI‑6733 is a high-speed analog output device designed to deliver simultaneous, multichannel updates for control and waveform output applications, such as stimulus-response tests (including acoustic distortion testing) and simulation (such as three-phase power simulation). In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PXI‑6733 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
product
NI-9262, 1 MS/s/ch Simultaneous, ±10 V, 6-Channel C Series Voltage Output Module
785503-02
1 MS/s/ch Simultaneous, ±10 V, 6-Channel C Series Voltage Output Module - The NI-9262 is a simultaneously updating analog output module. It features overvoltage protection, short-circuit protection, low crosstalk, fast slew rate, high relative accuracy, and NIST-traceable calibration. The NI-9262 module includes a channel-to-earth ground isolation barrier for safety and noise immunity.
-
product
4-CH Analog Output Module
ND-6024
- Channels: 4- Voltage Output: -10 V to 10 V- Output Isolation: 5000 VRMS- Resolution: 12-bit resolution- Accuracy: ± 0.02% of FSR- 7 TTL digital input
-
product
PXI/PXIe Analog Output/Current Loop Simulator Module - 12 Channel
43-765-002
The 41/43-765-002 is a 12-channel Analog Output Module designed to meet the requirements of industrial control applications utilising current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signalling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
product
Isolated D/A Converter 8 Channel, 250kSa/s
OTP2 module no.187
The PXIe‑4322 is a channel-isolated analog output module with built-in signal conditioning. The module provides accurate, simultaneous dynamic voltage and current outputs. By combining signal conditioning and D/A converters in one device, the PXIe‑4322 isolated analog output module offers smaller dimensions and higher measurement performance. In current mode, the module operates in all four quadrants, allowing current to be drawn and sourced. Thanks to isolation and outputs for higher voltages and currents, the module is particularly suitable for applications in the automotive sector.
-
product
NI-9264, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module
785190-02
25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module - The NI‑9264 is a simultaneously updating analog output module that accommodates higher‑channel‑count systems. Higher density modules conserve chassis space, which leaves room for other measurement types. Each channel has its own digital‑to‑analog converter. The spring-terminal version of the NI‑9264 uses a 36‑position connector for the output channels, and each channel has a ground connection.
-
product
PXIe-6739 , 16-Bit, 64-Channel, 1 MS/s PXI Analog Output Module
783801-01
16-Bit, 64-Channel, 1 MS/s PXI Analog Output Module—The PXIe‑6739 is a high-density analog output module. The device is ideal for applications such as stimulus-response tests and open-loop simulations at high densities. You can achieve the maximum sample rate if using up to 16 channels, where each channel is on a separate bank. The PXIe‑6739 also includes 20 digital I/O lines, four counter/timers, digital triggering, and advanced timing to meet a wide range of application requirements. Its digital triggering and PXI Express synchronization capabilities allow it to be coupled with additional data acquisition, motion, and vision products to create highly custom measurement solutions to test innovative designs.
-
product
Modbus Digital Input Output Modules
DAT3100 Series
The Datexel DAT3100 series is a range of Modbus digital input output modules. These cards or modules have the ability to accept digital voltage inputs and provide an output by the way of relays, NPN or PNP transistors. The DAT3100 devices can communicate with RS485 or RS232 on a Modbus or ASCII protocol making the DAT3100 series a very economical solution to large and small scale Data Acquisition. Combining these digital input output devices with the DAT9000 controllers and the DAT3000 analog input output modules make Datexel the smart choice where Data Acquisition is needed.
-
product
NI-9262, 1 MS/s/ch Simultaneous, ±10 V, 6-Channel C Series Voltage Output Module
785503-01
1 MS/s/ch Simultaneous, ±10 V, 6-Channel C Series Voltage Output Module - The NI-9262 is a simultaneously updating analog output module. It features overvoltage protection, short-circuit protection, low crosstalk, fast slew rate, high relative accuracy, and NIST-traceable calibration. The NI-9262 module includes a channel-to-earth ground isolation barrier for safety and noise immunity.
-
product
PXI/PXIe Analog Output/Current Loop Simulator Module - 8 Channel
43-765-003
The 41/43-765-003 is an 8-channel Analog Output Module designed to meet the requirements of industrial control applications utilising current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signalling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
product
Analog Output Module, 16-bit D/A
IP230A
Jumper-selectable output ranges give you the choice of unipolar or bipolar voltage output. And for greater flexibility, the IP230A module accepts conversion start triggers from software commands, or from external sources for synchronization to specific events.
