Filter Results By:
Products
Applications
Manufacturers
ATE Fixtures
Holding and positioning assemblies to guide UUT I/O access by automated test equipment.
See Also: Test Fixtures, PCB Test Fixtures, Board Test Fixtures
-
product
ATE Support
For the last 30 years, Terotest has offered a range of support services, from standard maintenance and calibration to ATE updates and legacy ATE replacement solutions.We provide, repair and exchange ATE modules, fixtures, adaptors and other hardware, as well as offering full maintenance contracts to our customers.
-
product
Test Fixturing
There are no good measurements without good test fixtures. Ideally the test fixture needs to make the electrical connection between the test instrument and the device-under-test (DUT) and be electrically transparent. ATE has developed fixtures for SMT components, leadless packages, and miniature coaxial interfaces, in such a way that the fixture effects can be removed, and the measurement reference plane can be brought right down to the DUT.
-
product
Lifts
Alum-a-Lift is proud to provide world-class material handling solutions for Electronics manufacturing, including a complete line of ATE lifts, ICT fixture lifts, and accessories.
-
product
ATE Self Test Fixtures
AL663
AL663 fixtures include all the electronic parts required to perform an effective test platform diagnostic. The AQ818 device allows to perform a series of tests, obtaining a report of the faulty instruments or switch modules and also a report about the relay contacts estimated life.
-
product
In-Circuit Test (ICT) Fixtures
At Forwessun we support and manufacture In-Circuit Test Fixtures for a range of Test Systems. We regularly build fixtures that are supported on a range of systems including - - HP3070- Agilent- Keysight- GenRad- TeradyneWith over 50 years in the industry, we provide a weatlth of knowledge and support to our customers. We are a global company and can support businesses all over the world with the help of over 30 experienced test engineers.
-
product
Faraday Chamber for RF w/Exchangeable Cassettes 340x350mm RCV 9025 for 6TL36
AN133
The Faraday Chamber is an add-on for the 6TL36 test handler. This kit is installed into the 6TL36 in the same way a normal test fixture would be installed, being the only difference the fact that different products to be tested will, from that moment on, only need an additional exchangeable cassettes to be tested.
-
product
80 DIOs, 8AIs, 8AOs JTAG Boundary Scan Resources Unit Expansion
YAV9JTAH
80 DIOs8 Ais8 AOsCompatible with all JTAG vendors
-
product
Fixture Kit 600x455mm RCV 8-slot for 6TL34
AG588
Stopper kit includedYAVCANCON2 for fixture identification not included
-
product
Functional Test Fixtures
Reliable connections to device under test (DUT) test points are essential for robust functional test. Bloomy provides rugged fixtures and cable sets (ITAs) built for thousands and thousands of cycles in manufacturing environments. With the industry’s best mass interconnects and internal electronic keying, our fixtures are easy to change out and are automatically recognized by the test system.
-
product
Fixture Self-Test Controller and Calibration Check
AQ818
The module AQ818 includes all the electronic blocks required to perform an effective test platform self-test. Thanks to this module, a chain of tests can be performed, which will end up not only with a report of the defective instruments or switch modules, but also with the relay contacts live expectancy report.
-
product
Fixture Kit In-Line 6TL35 455x600mm
AH500
Fixture Kit for Platforms featuring receiver Virginia Panel 9025 and external pusher system. Its heavy duty design supports more than 3000N.nnThe fixture kit includes the Base fixture (probe plate) as well as the Puhsers plate.
-
product
ATE
Below is a list of high speed scopes and BERTs that form an integrated extension to Advantest’s V93000 ATE tester. In addition to these instruments, Multilane offers turnkey solutions for ATE testing.
-
product
Docking / ATE
The iDock Series is a series of connectors ideal for use with automatic machine handlers in production testing. Floating bushings allow up to .04" of re-alignment. Use with a combination of various I/O modules and a max of 5,952 signal contacts simultaneously. The iDock series is rated up to 100,000 cycles.
-
product
ATE Solutions
Our custom, application-specific ATE Test Solutions offer a full test suite with Test Systems hardware, software, and support services.
-
product
RWR ATE MKII
MS 1111
Automatic Test Equipment (ATE) MKII is a customized tester, built to carry out LRU and card level testing for TARANG systems of all platforms. The purpose of ATE is to provide a user-friendly environment to test the LRUs and sub-systems (individually) for their functionality, perform specific tests of each LRU / sub-system and Card Level Testing. The card level testing facilitates troubleshooting down to a faulty signal flow path. The UUT tests are carried out by injection of the stimuli generated by the computer or the programmable test equipments and the responses from UUT / test equipments are feedback to the computer for evaluation and generation of reports.
-
product
Semiconductor ATE Systems
Our testers allow for the high-volume production of electronics that touch people’s lives in communication, safety, entertainment, and much more.
-
product
Fixturing
Terotest specialises in providing test solutions specific to customers' test applications. We understand that the interfacing and fixturing of a particular test setup can determine whether the application is a success or a failure, and therefore we strive to deliver solutions that are cost effective and suitable to user requirements.
-
-
product
RFIC ATE System
RI 7100A
The RI 7100A, which RI has shipped for over 10 years, has proven itself as the most advanced, reliable (> 4500 hours MTBF) and cost effective RFIC ATE System available. "Our recipe for high performance microwave test has always been dependent on an extremely elegant RF signal path while maintaining the most advanced microwave calibration software," said RI President, Mark Roos.
-
product
Fixture Kit
MF300
Due to careful selection of materials, use of modern manufacturing techniques, and supplying the kit "flat packed" for end-user assembly, Merifix fixtures kits are inexpensive enough to be used in low-volume production and in engineering labs for programming and debug tasks, where traditional fixtures would be too expensive.
-
product
ATE & Test Systems
Data Patterns' core business for over 20 years has been the development of Automated Test Equipment for critical aerospace requirements. Data Patterns developed a Multi Programmer with associated test automation software in 1994. Christened the DP-800 this product was adopted for the implementation of test rigs for Navigation Platform Test Benches, Engine Test Bed Automation, Cable Harness Test Systems, etc. This product was effectively utilized in the development of test benches required by Indian Space Research Organisation (ISRO) for the Polar Satellite Launch Vechicle (PSLV) and Geo Stationary Launch Vehicle (GSLV). Based on this foundation, the next generation test benches were developed in the cPCI architecture. Presently, Data Patterns develops cPCI based test systems for Laboratory applications as well as VME based test systems for challenging environmental conditions. Examples of test solutions built by Data Patterns are indicated below.
-
product
Test Fixture
16047E
Perform impedance evaluation of lead type devices of up to 120 MHz; includes a guard and a shorting plate
-
product
Fixturing Kit
10744A
The Keysight 10744A fixturing kit includes mounting hardware for a variety of Keysight measurement optics devices. A large base, multiple posts, and other accessories let you build structures -- such as tall, rigid towers -- that place optics in the center of a machine's work zone or wherever needed. The fixturing kit helps meet the physical requirements of a range of measurement applications.
-
product
Avionics ATE Power Subsystem
AMETEK Programmable Power, Inc.
*Provides eight channels of programmable DC power with output isolation function*Output disconnect function*Total control via Ethernet within power supply.*Mounted in custom in transportable shock-mount case.
-
product
ATE Computer
MS 1201
This system used for multi-purpose applications such as data acquisition and Automatic Test Equipment. ATE Computer has ISA Bus based eleven slots with inbuilt power supply. Micro Processor board or USB Controller is used to drive the back plane.
-
product
Custom Test Fixtures
Intrinsic Quality is proud to offer a variety of Test Fixture Development Services that include fixture building, tester interface building, harness building, troubleshooting, maintenance, design, and engineering. IQ’s fixtures are built to exacting specifications and configured to deliver quality production testing. Our global customers have trusted us for over 35 years to provide custom solutions applying leading edge technology. IQ consistently delivers cost-effective solutions with our client’s recognition and gratitude.
-
-
product
Test Fixture
OCP NIC 3.0
These test fixtures are necessary for testing within the OCP NIC subgroup (found under the OCP Server Work Group). These fixtures will arrive meeting the OCP NIC 3.0 Specification with a characterization of the boards. These fixtures mate with the OCP form factor connector, and will allow an electrical break out of each signaling lane.
-
product
Exchangeable Test Fixture
MA 2112/D/H/S-7
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 11,30 kg
-
