Pull Force
strength necessary to extract.
See Also: Force, Compression, Crimp Force, Pull off Force, Push Pull Force, Peeling, Tension, Gravity, Electrical, Magnetic
-
Product
Digital Force Gauges
-
AMETEK Sensors, Test & Calibration
These digital force gauges and torque gauges offer the best price performance value of any digital force gauge available, along with a high precision and an easy to use force measurement solution.
-
Product
Motorized Force Test System
MT Series
-
In the past, film extruders, paper producers, converters, and woven/non-woven fabric producers have had the choice of test stands and universal test machines which are either value-priced peak-force-only machines, or expensive computer-operated integral-load cell machines. Now you can have the best of both worlds in a single instrument. The series MT-1500, a simple to use computer operated tester, with Quality Control software for automatic calculation and graphical display of break, elongation, yield, modulus, and other, tension and compression force information.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type A, Ø0.80mm, 305gf
K100-A080305-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style A, Tip Diameter Ø0.80mm, Spring force 305gf, Steel with Gold Plating.
-
Product
Mixed-Signal Active Load Pull System
MT1000 And MT2000 Series
-
The MT1000 and MT2000 mixed-signal active load pull systems are the best commercially proven solutions capable of performing load pull at high speeds of up to 1000 impedance/power states per minute with no limitation on Smith Chart coverage, under the following conditions:Single-tone CW and pulsed-CW RF signalDC and pulsed-DC biasTime-domain NVNA voltage and current waveforms and load linesFrequencies between 1 MHz and 40 GH
-
Product
PXI Module Adapter, Pull Thru Adapter, Receiver, 1 Position
510109462
Adapter Module
PXI Module Adapter, Pull Thru Adapter, Receiver, 1 Position.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type Q, Ø0.80mm, 230gf
K100-Q080230-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style Q, Tip Diameter Ø0.80mm, Spring force 230gf, Steel with Gold Plating.
-
Product
Wire Crimp Pull Tester (Motorized)
WT3-201M
-
The WT3-201M motorized wire crimp pull tester is designed to measure pull-off forces of up to 200 lbF [1 kN] for wire and tube terminations. The tester conforms to numerous UL, ISO, ASTM, SAE, MIL, and other requirements for destructive testing. Non-destructive testing is also possible, such as pulling to a load or maintaining a load for a specified period of time, as per the requirements of UL 486A/B. Programmable pass/fail limits with red and green indicators and audio alerts help identify non-conforming samples.
-
Product
Shear Beam Force Sensors For Pull/push Direction
-
INELTA Sensorsysteme GmbH & Co. KG
Inelta Force Sensors operate with foil strain gauges
-
Product
Force Data Acquisition Software
-
SW-1X data acquisition software is for force gauges with RS-232 output.SW-2X data acquisition software is for collecting force and displacement data from RS-232 output force gauges, with a -s test stand.Force Recorder data acquisition software is for ZTS & ZTA force gauges with USB output. Force Recorder Pro collects both force and displacement data with ZTA gauge and FA test stand.
-
Product
High Force Type Prbobe For PCB, K100 Series 100 Mil Pitch, Receptacle With Wire Wrap Pin
KR100-WP
Spring Probe
K100 Series, Pitch 100mil, Receptacle, with wire wrap pin. Brass with gold finish.
-
Product
Lo-PRO®file ZIF (Zero-Insertion-Force) Socket
Series 526
-
LO-PRO file Zero Insertion Force Socket. A choice of 24, 28, or 40 pin count devices can be inserted without bending or otherwise damaging the legs, since no force is required to either insert or remove the component from the socket. A metal cam provides strong, smooth action as it moves to a positive stop, compressing the double-sided contacts, ensuring a gas-tight seal.
-
Product
Digital Force Gauge
-
*Compact and light weight*3-way power supply*Display hold function is equipped*Easy zero adjustment function*Automatic recognition of the type of sensor*Judgment function (Hi&Low) is equipped
-
Product
Atomic Force Microscope
AFM
-
Atomic Force Microscopes are the most widely used SPM microscopes. They can be applied in fields that span from surface science, semiconductor technology, magnetic media, polymer science, optics to biology, chemistry and medicine.Absolute positioning with an accuracy of 2 nm.
-
Product
Forced Air Cryogenic Cooling
FixTreme TE
-
FixTremeTE is a cost-effective standalone alternative to mechanical or forced air cryogenic cooling. When paired with a Testforce dbGuard Series RF shielding test enclosure, performing at temperature RF & microwave functional testing is simple.
-
Product
Bond Force Measurement And Calibration Systems
BFS-20
-
Based on its design and easy handling it can be used also on other brands to measure the bond force.
-
Product
Pull Out Device
BCL-1
-
This Pull out device BCL-1 is designed and manufactured according to relevant standard requirements of IEC884-1/ GB2099.1-2008 and other electrical accessories standards, Mainly used to test the needed maximum force when the plug pull out from socket and the minimum force when single stage plug pull out from socket, and to inspect whether the socket can withstand the lateral stress imposed by electric plug into the socket. This device is applied to plugs and sockets which rated voltage no more than 250V and rated current no more than 16A.Specifications: • Weights: 36N*1, 5.4N*1, 5N*2, 4N*1, 2.6N*1; • Standard testing plug: each one for Dipolar 10A, tripolar 10A and 16A • Standard test bolt: Each one for 1.5N and 2N • 1 set of clamping device • 1 set of Weights tray • Lateral stress weights 5N*1 • 1 set of lateral stress bar
-
Product
Force Tensiometers
Sigma 702ET
-
The Sigma 702ET Transformer Oil Analyzer has been specifically designed to guide the user through the measurement of interfacial tension of transformer oil according to relevant standards.
-
Product
Quartz Impact Force Sensors
-
Impact-style sensors are specifically designed for impact force measurements. The sensor is typically mounted in a free-standing manner with the installed impact cap directed toward the oncoming object with which it will collide.
-
Product
Conductivity Type (P/N) Checker By Contact Thermo-electromotive Force Method (seebek Effect)
PN-12α
-
*Thermo electrode and cold electrode is mounted detecting part of measuring probes*Possible to check most figure of sample such as single crystalline silicon wafer, bulk, ingot and so on*Please select from 2 types;1) 2 probe ver.(Hot probe, Cold probe),2) 1 probe ver.(Hot & Cold probe)
-
Product
Ergonomic Force Gauges
DMG Series
-
AMETEK Sensors, Test & Calibration
The DMG ergonomic gauge lets you objectively measure manual muscle strength and functional task requirements for almost any application.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type K, Ø1.50mm, 155gf
K100-K150155-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style K, Tip Diameter Ø1.50mm, Spring force 155gf, Steel with Gold Plating.
-
Product
ZIF (Zero-Insertion-Force) Socket
Series 516
-
Zero Insertion Force Socket. A choice of 24, 28, or 40 pin count devices can be inserted without bending or otherwise damaging the legs, since no force is required to either insert or remove the component from the socket. Contacts are normally open and are closed by a unique cam action controlled by dual lever arms. The last 15° of movement of the cam provides a wiping action to the contacts on the legs of the device to remove any residue, ensuring a gas-tight seal.
-
Product
Atomic Force Microscope
Flex-Mount
-
Flex-Mount is a unique AFM that can be configured to acquire high-resolution information on large, non-planar and demanding samples. The Flex-Mount solution combines the superior resolution and performance of the Nanosurf FlexAFM scan head with the integrability of the Nanosurf NaniteAFM.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type L, Ø1.50mm, 230gf
K100-L150230-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style L, Tip Diameter Ø1.50mm, Spring force 230gf, Steel with Gold Plating.
-
Product
High Force DMA
DMA+ Series
-
*The new DMA+ series instruments are dynamic testing machines based on a innovative concept of one-piece high rigidity test frame.*They are dedicated to the accurate analysis of the viscoelastic properties of most advanced materials.
-
Product
Electromagnetic Force Micro Tester
Micro-Servo
-
This is a multi-functional fatigue testing machine suitable for specimens, structures and full-sized parts. It is an overhead actuator type with a broad test space, so it is ideal for various types of environmental tests, such as those in corrosion tanks or constant temperature tanks.
-
Product
48 Ω HMM Pulse Force Probe
PHD-HMM-48-1
-
High Power Pulse Instruments GmbH
*High current wafer-level and package-level 98 Ω HMM probing with grounded DUT*Built-in high surge 48 Ω pulse reflection suppression resistor up to 80 A peak*Fast rise time < 0.5 ns due to low inductance GND loop*Variable pitch from 50 µm to 5 mm*Tungsten replacement probe tips*SMA pulse force pigtail*Compatible to PHD-3001A interface*High reliability
-
Product
Ergonomic Force Gauges
MSE100 Series
-
AMETEK Sensors, Test & Calibration
The MSE100 ergonomic gauge is a simple-to-use, ergonomically designed mechanical instrument ideal for muscle strength evaluations and job task analysis.
-
Product
Full Bridge Thin Beam Force Sensors
TBS SERIES
-
The TBS Series thin beam force sensors many different parameters found in medical instrumentation, home appliances, process control, robotics, and automotive are exceptionally suited for small load measurements. They are designed to measure and many other high volume applications. A specially developed integrated strain gage includes all balancing, compensating and conductive elements and is laminated to the beam to provide excellent stability and reliability.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type H, Ø0.80mm, 305gf
K100-H080305-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style H, Tip Diameter Ø0.80mm, Spring force 305gf, Steel with Gold Plating.
