-
Product
Conventional friction and wear tester
EFM-III
-
The measurement unit of A&D's conventional friction and wear tester has been adjusted to enable the measurement of friction characteristics with higher precision.
-
Product
Wrist Strap and Foot Wear Testers
-
Connects to utility ground when plugged inQuick, easy installation and grounding of both wrist straps and table mats.Tests entire circuit - wrist strap, cord and skin contactReliable resistance testActs as common point ground for the worksurface
-
Product
Ferrous Wear Meter
Parker Kittiwake
-
Parker Ferrous Wear Meter (FWM) detects abrasive ware metal iron particles in an oil samples taken from lubricated engine, liner and cylinder machinery.
-
Product
Abrasion/Wear
-
Our Capabilities*Taber Abrasion*RCA Wear Tester*Resistance to Crocking*Washability*Pencil Hardness*Finish Adhesion
-
Product
Bearing friction and wear tester
-
This testing machine evaluates the frictional characteristics of radial bearings. The circuit system adopted for the lubricant enables heating up to 80C.
-
Product
Power Circulation Type Tire Wear Tester
-
This test machine is a tire wear test device that employs an electric servomotor power circulation system.
-
Product
Reciprocating friction and wear tester.
-
This testing machine is used to evaluate surface conditions such as friction faces of materials by measuring the frictional force.
-
Product
Friction & Wear Testing Machine
-
Jinan Scientific Test Technology Co. LTD.
Friction & Wear Testing Machine
-
Product
Mechanical Tester
-
NANOVEA Mechanical Tester is the most versatile nanoindenter and scratch tester capable of precisely measuring the micro- to nanomechanical properties of wide ranges of materials from thin films, coatings, ceramics and composites to polymers and bio materials via Indentation, Scratch and Friction testing. All NANOVEA Mechanical Tester models come with true feedback load control from independent load and depth sensors that provide unmatched accuracy and the highest repeatability available on the market. This technology allows a user to perform Nanoindentation and Microindentation for Hardness and Elastic Modulus Testing, Stress vs Strain Analysis, Creep and Relaxation, Loss and Storage Modulus, Yield Strength and Fatigue, Fracture Toughness and Nano-scratch & Micro-scratch for Scratch Hardness Testing, Multi-pass Wear Test, Cohesive and Adhesive Failure Testing as well as Coefficient of Friction testing, all available on one system.
-
Product
Affordable ICP-OES Spectrometer
Ultima Expert LT
-
HORIBA Scientific develops and manufactures high performance ICP-OES spectrometers for more than 35 years.• The new Ultima Expert LT provides high performance at affordable price for laboratories with challenging samples.• Ultima Expert LT integrates high efficiency Jobin Yvon optical design capable to achieve optimal performance for a large variety of sample types and matrices.• Ultima Expert LT is driven by the powerful Analyst software featuring a large variety of analytical functionalities for tailored control and analysis.• The robustness of the Ultima Expert LT makes it ideal for applications common to mining, chemicals manufacture, salt production, wear metals in oil analysis, petrochemical and metallurgical production• Gain in performance with the Ultima Expert LT for your most challenging applications!
-
Product
Standard Digital Multimeter - Auto Ranging
MM39
-
The MM39 is an auto-ranging multimeter with a large rotary switch for easy selection of the required test, even when wearing gloves. There are two test buttons, one to lock the range and the other to hold the results which are displayed on a 3½ digit LCD screen.
The main test functions are AC voltage and DC voltage and current and resistance. The MM39 measures both AC and DC voltage between 0.1mV to 600V and AC and DC current between 10mA to 10A. There is a diode test and an audible continuity test which sounds at less than 25Ω.
-
Product
Safety Proximity Sensors
-
Leuze electronic GmbH + Co. KG
With their encapsulated and contactless design, safety proximity sensors are insensitive to contamination and humidity. They operate free from wear and also have a long life expectancy, even with frequent operating cycles. They are also used wherever it is difficult to precisely guide the moveable protective device. All devices feature a high-strength plastic housing. Furthermore, the devices with RFID transponder provide maximum protection against tampering.
-
Product
Tribocorrosion Tester
ASTM G119
-
Tribocorrosion involves studying Wear Evaluation of Protective Coatings. It involves mechanical and electrochemical interactions between components in motion. Rtec Tribocorrosion modules measures inline current, voltage, friction, wear, temperature , down force, ear, acoustic emissions at all times. Currently used by several Fortune 500 firms globally.
-
Product
High Speed Test Bench
AT444
Test Platform
AC motor with mechanical multiplying gearbox test benches allow precise programming of all drive parameters required for accurate rotating devices test.The use of special high-speed bearings, mechanical components and parts wear resistant leads to a large life. The supply includes the electronic drive and control as well as the entire oil cooling unit.
-
Product
6, 8 GHz, 4 Channel Programmable Attentuator
QPA8, PA8
-
This device has low impedance mismatch, high bandwidth, wide dynamic range and is capable of rapid state change. The QPA8 can be an attractive alternative to either the manually operated microwave attenuator switches, which are expensive and are switched very slowly, or the relay attenuators which are expensive and wear out quickly. Attenuation is controlled in standard steps of 0.0625 dB. The 10 bit programmable range results in the full 210=1024 steps yielding a dynamic range of 0 to 63.9375dB. Non-standard custom step sizes are available.
-
Product
PXI Dual 4 to 1 RF Multiplexer 6GHz 50 Ohm SMA Terminated
40-882-002
Multiplexer Module
This PXI multiplexer exhibits low VSWR characteristically over the full operating frequency range and consistent insertion loss characteristics. The use of solid state switches ensures a long service life with no wear out mechanism, making the 40-882 MUX ideal for ATE systems requiring frequent and fast operating RF switching.
-
Product
RF Safety Monitoring
MVG EME Guard Plus
-
The EME Guard Plus is designed to record EMF exposure near antennas while continuously monitoring potential over-exposure. Lighter than the previous model, the EME Gaurd Plus makes it easier for workers to wear on the job. The longer battery life and extended memory capacity enable more measurements to be recorded.
-
Product
Three Phase Power Monitoring
-
PRÜFTECHNIK Condition Monitoring GmbH
A three-phase power monitor detects changes in electrical variables. With power monitoring on your assets, you can help reduce wear and damage, while also identifying what’s causing it. The Fluke 3540 FC three-phase power monitor can be used remotely or through a stationary connection.
-
Product
13 GHz, 4 Channel Programmable Attentuator
QPA13
-
This device has low impedance mismatch, high bandwidth, wide dynamic range and is capable of rapid state change. The QPA13 can be an attractive alternative to either the manually operated microwave attenuator switches, which are expensive and are switched very slowly, or the relay attenuators which are expensive and wear out quickly.
-
Product
PXI/PXIe RF Multiplexer, Triple 4-Channel, Terminated, 8GHz, 50Ω, SMA
42-882B-003
Multiplexer Module
This multiplexer exhibits low VSWR characteristically over the full operating frequency range and consistent insertion loss characteristics. The use of solid state switches ensures a long service life with no wear out mechanism, making the 40/42-882B MUX ideal for ATE systems requiring frequent and fast operating RF switching.
-
Product
SOLAS Compliant Container Weight Verification System
-
Cargo Hawk is a non-intrusive SOLAS compliant Container Weight Verification system. Using Datum Electronics highly accurate and patent protected innovative bolton strain gauge sensors, Cargo Hawk seamlessly integrates to new and existing container handling equipment, without the need of introducing expensive high wearing consumable load monitoring hardware.
-
Product
Washability & Abrasion
-
Improved mechanical resistance to wear is a key requirement of a wide range of products. From coatings to clothing, leather to upholstery, keypads to plastic toys, a product’s ability to resist wear is an important characteristic. There are testing methods relating to the ‘abrasion by friction’ concept. Others are based on the projection of abrasive particles on to the test specimen. These techniques provide valuable information about materials and processes.
-
Product
Resistivity Meters
-
Periodic compliance checks of ESD work surfaces are super important. Monitors only verify the ground plane, or path to ground. The surface itself can wear down, become dirty, or if you use low quality mat—just not hold up. A handheld Surface Meter is great for running monthly, or prescriptive compliance verification of your ESD surfaces.
-
Product
ADI Test Fixture
TA-6500
-
The TA-6500 test fixture combines the features of the OEM's Instrument Servo Tester(T307962), the Pointer/Flag Test Fixture(T307951) and the AD-650/600 Test Panel(T334043) all into one panel to facilitate testing of these Attitude Director Indicator's. The panel switches and adjustment pots are labeled to match the test procedure numbers and the duplicity in marking makes it easier for the technician to understand each function. The UUT interface is through a 96 pin zero insertion force(ZIF) type connector to minimize contact wear. The expanded localizer and nav input pins J2-34/35 are exposed on the panel to facilitate the insertion of a 200 ohm shunt when required. The fixtures rear panel has connectors for the required dual API/Synchro transmitter interface while the panel switches provide the correct routing of each.
-
Product
Multi Function Tribometer
MFT-5000
-
The state of the art Rtec Multi Function tribometer Mft-5000 is globally regarded as the most versatile and technologically advanced tribometer. Manufactured at silicon valley, California it is used by several top labs, universities and industries. The tribometer offers next generation patented force sensors with ultra low resolution, highest speeds and wide environmental control range than any other commercially existing tribometer. The patented integrated 3D profilometer allows to analyse surface change vs time. The universal tribometer MFT5000 allows to create a comprehensive report on friction, wear, tribology and surface analysis.
-
Product
Laser Pulley Allignment System & Belt Pulley Alignment Tools
-
PRÜFTECHNIK Condition Monitoring GmbH
Correcting belt pulley alignment significantly extends machinery service life and lowers power consumption by decreasing wear and improving efficiency. While you can identify misalignment visually or with a straight edge, using a pulley alignment laser tool makes finding angular, vertical, and horizontal misalignment much faster and easier. Our laser belt alignment tools and pulley alignment tools are easy to use and can pay for themselves within only a couple of months.
-
Product
Non-destructive Eddy Current Testing of Long Products such as Tubes, Rods, Wire, and Profiles
DEFECTOMAT® Product Familiy
-
Foerster Instruments, Incorporated
The DEFECTOMAT systems by FOERSTER were specially developed for quality testing and process monitoring of long products. From hot testing to all bright steel processing steps, the surfaces of semi-finished products made from austenitic, (non) ferromagnetic metals can be tested for defects. The DEFECTOMAT systems operate in a contactless and non-destructive manner in accordance with the eddy current method and are used for detecting short defects, such as holes or localized defects and transverse defects. The systems detect defective materials fully automatically and reliably. Defects can be marked, classified, and automatically discarded. the test speed of up to 150 m/s facilitates 100% testing, even at high production speeds. The systems benefit from low operating costs and frugal energy consumption as well as low maintenance costs, few wear parts, and low use of materials.
-
Product
Electromagnetic Flow Meters
-
Electromagnetic (mag) flow meters are volumetric flow meters that do not have any moving parts to wear down, reducing the need for maintenance or replacement.
-
Product
Automatic Calibration Module
ACM2509
-
ACM2509 is an automatic calibration module that can be used with all CMT Vector Network Analyzers operating in frequency range up to 9 GHz. It is a fully automatic USB-controlled and powered electronic calibration module. Minimizing the number of steps required by technicians reduces the risk of human error and expedites the calibration process. Automating the calibration routine also reduces wear and tear on the analyzer and RF cables. To perform full two-port calibration, each end of the ACM need only be connected to the analyzer once, as opposed to seven connections with a traditional calibration. The ACM also contains a factory characterized 20dB in-line attenuator which acts as a simulated device under test (DUT). The confidence check feature loads the factory stored DUT into memory so proper calibration can be verified.
-
Product
Industrial Vibration Sensor
IVS-500
-
The new IVS-500 Industrial Vibration Sensor is the key to fast acoustic quality inspection, structure-borne noise analysis and reliable pass-fail decisions. This Laser sensor measures reliably, in demanding industrial environments, without contact and therefore without wear and on virtually all surfaces. Costs and yields are therefore optimized by reducing false rejects in the production and assembly process. The simple setup and ruggedized sensor design of the IVS-500 enable a smooth integration into production test systems. Complemented with the software tool QuickCheck, Polytec offers a comprehensive solution for reliable pass/fail analysis.
