Integrated Design Environment
-
-
Product
Linerizers and Integrators
-
Linearizers with freely selectable parameters are designed for industrial applications in which non-linear analog signals or frequencies are to be linearized on the display and at the analog and data outputs. Depending on requirements, devices with 19 to 4000 linearization points are manufactured. The linearization can be entered directly via the device keyboard or via the serial interface from the PC. Several linearization methods are available, such as direct overwriting of the display with the desired value, table with setpoint and actual values or polynomial linearization.
-
Product
PCB Design and Assembly
-
Innovative Circuits Engineering, inc
Turnkey services for Printed Circuit Boards: Design, Fabrication, Assembly and Testing
-
Product
Computer-Aided Design
CAD
-
Create, modify, analyze, and optimize designs through enhanced CAD capabilities like drafting, modeling, rendering, generative design, simulation and analysis, additive manufacturing, and more.
-
-
Product
Flexible Test Environments and Integration Services for your Integrated System Tests
TESTERLYZER® Frame 4.0
-
The TESTERLYZER® Frame 4.0 provides a flexible test environment for vehicle control units in an integrated system and is easily accessible from all sides. Customized adaption is provided for panel designs, control unit holders and cable adapters. A TESTERLYZER® I-Box 4.0 is a standard component of the TESTERLYZER® Frame 4.0 and provides the basis for a wide range of structures for the testing of control units, software and services relating to vehicles in research and development. The backbone of the I-Box provides all signals required with distribution to standardized adapter sockets and interfaces. The modular assembly structure ensures swift and safe setting up of the required test environment.
-
Product
Integrating Spheres
-
Integrating spheres are used especially for measuring divergent light sources such as LEDs. The light is introduced through the input port, then reflected many times by the highly reflective interior of the sphere until it illuminates the inner surface uniformly. A detector samples a small fraction of this light to measure the total power input. Ophir integrating spheres have a highly reflective diffuse white coating for measurements independent of beam size, position and divergence. There are several sphere sizes, apertures and wavelength regions available. The large IS6 series has 2 configurations for measuring divergent or parallel beams.
-
Product
Customised Design
-
However, there is no doubt that a customised PSD will ensure the best performance from your product whether it be an instrument or a complex measurement system.
-
Product
Best In Class, Easy To Use Design Software
Lattice Radiant Software
-
Full Featured, Easy to Use Tool Suite - Lattice Radiant software offers all the best in class tools and features to help users develop their FPGA applications efficiently and effectively. Powerful yet intuitive tools provide fast design starts and precise implementation.
-
Product
LabVIEW Tools for Digital Filter Design and Implementation
LabVIEW Digital Filter Design Toolkit
-
The LabVIEW Digital Filter Design Toolkit extends LabVIEW with functions and interactive tools for the design, analysis, and implementation of digital filters. New digital filter users can explore classical designs with the built-in interactive design tools, while experienced users can find a breadth of algorithms, filter topologies, and analysis tools for both fixed- and floating-point digital filters. For fixed-point filters, you can model quantization effects, optimize numeric representation/topology, and deploy the design on a digital signal processor or FPGA using automatically generated ANSI C or LabVIEW FPGA code.
-
Product
LED Tester0.3m-2m Integrating Sphere
CX-8000
-
Shenzhen Chuangxin Instruments Co., Ltd.
Measure Luminous Flux, Luminous efficacy, radiant power, Spectral Power Distribution, Chromaticity Coordinate, Correlated Color Temperature, Peak Wavelength, Dominant Wavelength, Spectral Half Width, Color Rendering Index, Colorimetric Purity, red ratio, Standard deviation of color matching(SDCM), voltage, current, power, power factor, harmonics, and etc. It meets the requirements of CIE standards.
-
Product
Integrated Systems
-
Power, flexible and based on commercial open standards, Integrated Systems from Abaco are pre-integrated and pre-qualified, so they're ready for immediate deployment - minimizing cost, risks and program lead time.
-
Product
Custom Designed Test Fixtures
-
We specialize in automated test systems for both RF and digital devices, modulesand systems. Please call to discuss your test requirements.
-
Product
System Integration
-
The provision of a basket of services for Auditoriums such as audio-visual systems, stage lighting, stage rigging, building control systems, communication systems and information technology systems. A proper understanding of the various disciplines involved is the key to successfully integrating the diverse component parts. The final solution must perform as one unit with a high degree of simplicity to the end-user. The result will be a solution that, while extremely complex, appears simple, logical and easy to use. Sri Comm has successfully designed, installed and commissioned several projects of this nature.
-
Product
Integrated Balun Probes
-
This is an example of a 900 MHz Integrated Balun Probe. It incorporates a 50 ohm unbalanced to 200 ohm balanced differential transformer. The probe can be built with or without a center tapped ground needle and may also incorporate DC bias through the differential pair or via separate needle contacts.
-
Product
Constant Temperature Integrating Sphere
IS-*MT
-
According to requirement of IEC standards, the standard test temperature is 25℃, but high power lamps such as HID lamps and LED outdoor luminaires will produce a lot of heat during the test, thus the temperature inside the integrating sphere can not meet the requirements of IEC standards. Lisun Group designed the Constant Temperatured Integrating Sphere which allows the lamp was tested in a constant air temperature.
-
Product
Integrating Sphere Solutions
-
An integrating sphere is a light collector which takes advantage of physical geometry to homogenize any radiation being emitted inside by relying on a high-reflectance coating material. Depending on the wavelength range the end user using a sphere with, different coatings have different advantages based on the application.
-
Product
Multi-Role, Low-SWaP Laser Target Designator
StormCaster™-DX
-
The Teledyne FLIR StormCaster™-DX is a multi-role, low-SWaP laser target designator payload designed to affect the STANAG-compliant terminal guidance of laser guided munitions. StormCaster-DX is tightly integrated with the R80D SkyRaider™ UAS to leverage its class-leading payload capacity, multi-mode operations (tethered/untethered & mounted/dismounted), and AI-CV-based targeting capabilities.
-
Product
Multi-Functions Environment Tester
-
Precision Mastech Enterprises Co.
A portable, handheld, all-in-one device designed to measure multiple ambient parameters simultaneously.
-
Product
Thin Film Design Software
-
Scientific Computing International
SCI offers software tools for optical thin film design, material analysis, ellipsometry, and spectrophotometry. SCI’s current standalone optical thin film software includes:
-
Product
Product Design and Experience
Catia
-
CATIA delivers the unique ability not only to model any product, but to do so in the context of its real-life behavior: design in the age of experience. Systems architects, engineers, designers and all contributors can define, imagine and shape the connected world.
-
Product
ATE System Integration
-
Cyth Systems is a Systems Integration Company specializing in Automated Test (ATE), Embedded Controls, and Machine Vision. Our skilled and experienced team uses their natural talent for problem-solving to create solutions in a wide range of industries. We build our solutions starting with the National Instruments (NI) platforms including LabVIEW and PXI, and by adding best-in class sensors and components.
-
Product
OEM Optical System Design and Manufacturing
-
Prior Scientific has successfully developed many innovative and custom OEM products for our industry partners. Any opportunities to develop, design or manufacture OEM products are always considered.
-
Product
Sparklike Laser Integrated
-
Sparklike Laser Integrated™ is an automated insulating gas measurement station, which is integrated in the IG production line. In addition to measuring the gas concentration of IGUs, it helps with monitoring possible over fill and optimizes the use of butyl.
-
Product
Test Stand, Fixture Design and Manufacture
-
As your partner, Trialon’s commitment to providing our customers with custom test stands, test and vibration fixtures that optimizes the sample test. Our experienced staff can design and manufacture a test stand or fixture for almost any product.
-
Product
19" enclosure in excellent design
Stylebox-15-e-motion
-
A portable desktop enclosure according to 19" standards. It can also be used as a 19" plugin device. The scalable EMC protection, color and design variants make the box the first choice for high-end electronics.
-
Product
ATE Integration
-
Want to improve the overall test coverage of your assembled boards? It’s easy. Simply combine or integrate your JTAG Technologies boundary-scan tools with your existing automatic test equipment (ATE). We work with any vendor of in-circuit testers (ICT), flying probes (FPT) or functional testers (FT).We offer solutions for most of the available automatic test equipment systems, in addition we can support you with customized integrations for your existing automatic test equipment (ATE).
-
Product
13.3" X86-Based Integrated POS System
USC-513K
-
Supports DeviceOn/iService software for remote device management, 13.3" FHD LCD (LED backlight) with PCAP touch. Ultra-thin design with 14 mm narrow bezel, Multi-function base integrated thermal printer and barcode scanner.
-
Product
Integration Tools
-
Products with unique and distinct uses such as EDID emulators, power supplies, ground loop isolators, and IR accessories.
-
Product
Integrating Sphere Spectroradiometer System for LED
LPCE-2(LMS-8000)
-
LPCE-2(LMS-8000) is an Integrating Sphere Spectroradiometer LED Testing System for identifying the performance of single LEDs and LED lamps. LED’s quality should be tested by checking its photometric, colorimetric and electrical parameters. According to CIE 127-1997 and IES LM 79-08 standards, it recommends using an array spectroradiometer with integrating sphere and photometer head to test SSL products. LISUN GROUP developed LPCE-2 test system for LED products.
