Automated Test Equipment
equipment that automatically analyzes functional or static parameters to evaluate performance.
See Also: ATE
-
Product
Water Leak Detection Equipment
-
Find and pinpoint leaks on a water network under paved and unpaved surfacesPrevent unnecessary excavation worksLocate the leak at valves and hydrants, in water pipes of small diameters and in hard-to-reach places by using special extra toolsIsolate parasitic noise and focus on the potential leak sound
-
Product
Flight Control System Test Platform
Test Platform
The Flight Control System Test Platform provides a hardware in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of Flight Control Systems (FCS) of both commercial and military aircraft. The system simulates control surface activities from multiple combinations of rudder, flaps, elevator, aileron, and engine controls to the FCS. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation test systems.
-
Product
PrimaTest Automation Services
-
PrimaTest values the relationships they build with their clients and work hard to become a part of your team. Creating this close bond allows PrimaTest to integrate with your process and use their many scalable and maintainable solutions to help you start automated your test cases fast.
-
Product
Control and Automation
-
Extron Control and Automation solutions simplify meetings, streamline presentations, and operate your core infrastructure across the enterprise.
-
Product
Electronic Ballast Automatic Test Equipment
ATE-1
-
Test series connection, parallel connection and series/parallel connections of the electronic ballast (about 15 kinds of connections), available for various electronic ballast. • With a precise resistance box, tube is substituted for the resistance, can act as many as 6 tubes. Resistance value: 1-4095Ω adjustable. • Measure input parameters (vrms, irms, w, pf, harmonics, etc), output parameters (on-circuit voltage, lamp voltage, filament voltage, lamp current, lamp power, oscillatory frequency), can also test the ballast efficiency, abnormity protection, and power symmetry of partial rectifier effect and etc. • Program controlled AC power source to guarantee the smart choice of input voltage and the frequency. • Equipped with 17 inch LCD controlled machine, specially designed A/D combined with special CPU, has the two left and right testing interfaces to achieve stability of data and high- speed testing. • We can make the special-designed product for you and promise to upgrade the software for free.
-
Product
Primary Test Equipment
LET-2010-RD
-
It allows to perform with sufficient power, all the primary current injections to test the proper function and wiring of all the elements that compose the protection and measuring section in a substation.
-
Product
Stereoscopic Zoom Microscope Automation
SZ-2000
-
Applied Scientific Instrumentation
Based on ASI's proven DC servo motor technology, the SZ-2000 automates stereo zoom microscopes. The unit can be configured for motorized focus only, motorized focus with automated zoom control, or motorized focus with automated zoom control and an automated XY translation stage. The Z axis focus resolution varies slightly depending upon the model of the microscope, with 0.8 microns being the smallest step size available on a Nikon SMZ800.
-
-
Product
RF Automated Accelerated Reliability Test Station (AARTS)
RF-HTOL
-
The RF Automated Accelerated Reliability Test Station (AARTS) systems are designed to stress devices with RF, DC, and thermal stimulus. The systems were designed from their inception to include RF stimulus - it was not added as an after-thought. Hence, the software and hardware are fully integrated and provide full-featured support.
-
Product
Automated Testing Services
-
Thorough automated testing can include thousands of repeated test cases to check for overall product stability, interoperability in a crowded ecosystem, niche failures, accelerated life and performance limits. Our automation testing services are a key component to developing: Android and Apple phones, Car Kits, Audio Equipment, Medical Devices, IoT Products, Development kits, Phone apps, Infotainment, plus more.
-
Product
Automated I-V/AOI/EL and Sorting System
-
OAI’s High Performance In-line Automated-I-V Testing, AOI/EL Inspection and Sorting/Binning System for Various Si Solar Cells. The 10000A-I-V System is a unique and reliable I-V testing, AOI/EL Inspection and Sorting / Binning system for testing of Mono, Multi-Si, C-HJT and other full Size (156mm x 156mm) and/or Cut-cell (156mm x 39mm or 156mm x 31.2mm or other custom sizes) Si Solar Cells.
-
Product
Automation Products & Techniques
-
CETAC Automation first produced the ASX-500 autosampler in 1993 in response to customer demand. Now, with over 30,000 autosamplers in various markets, Teledyne OEM Solutions has a wide selection of autosampler platforms and technologies to chose from to meet your market needs.
-
Product
Power Quality Monitoring Equipment
-
Outram Research Ltd manufacture, sell and hire a wide range of Power Quality Monitoring Equipment. From a single phase, plug and play instrument for solving residential Power Quality complaints to comprehensive 3 phase, 8 channel, high speed troubleshooting technology used by Power Quality Consultants, Distribution Network Operators and Electrical Utility Companies around the world.
-
Product
Glass Vials Testing Equipment
-
Glass vials - as used in medicine - can be checked for vacuum before and after being put into storage.
-
Product
Automated Probe Calibration
AutoClock
-
Metrology Software Products Ltd
AutoClock is the first product in history which makes it possible to fully automate the probe calibration process. It provides fast, accurate and automated tool axis setting. It takes seconds to automatically set the tool axis offset to microns. This enables the probe to complete the automatic calibration process without human intervention.
-
Product
Semi-Rigid Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131G
Test Port Cable
The Keysight 85131G is a 53 cm (21 in) long1 semi-rigid cable with a 3.5 mm female2 to 3.5 mm male connector. Cable frequency range is dc to 26.5 GHz with a return loss of 16 dB or better. Insertion loss is 0.3 * sqrt (f) + 0.2 dB (where f is frequency is GHz) for the test port connector, and 1.8 dB at maximum frequency for the device connector. Phase stability of semi-rigid/flexible cables is characterized with a 90 degree bend using a 4 inch radius. Stability1 of the Keysight 85131G is 0.06 dB and phase is 0.16o * f + 0.5o (where f is frequency in GHz).
-
Product
Primary Test Equipment
LET-4000-RD
-
It allows to perform with sufficient power, all the primary current injections to test the proper function and wiring of all the elements that compose the protection and measuring section in a substation.
-
Product
Shield Level / Pathloss Equipment
SG1000B/PR1000A
-
The SG1000 Signal Generator and PR1000A Preamplifier have been designed to simplify the measurement of shielding integrity in a shielded enclosure. When coupled with a high stability spectrum analyzer and an appropriate selection of test antennas, the SG1000/PR1000A combination can measure shielding effectiveness at all of the NSA 94-106 (supersedes NSA 65-6) defined test frequencies from 1 kHz to 10 GHz.The PR1000A amplifies the received signal from the test antenna and overcomes the high noise figure of the companion test receiver or spectrum analyzer. The PR1000A will ensure that the system noise figure will be less than 4.5 dB at all test frequencies from 1 kHz to 10 GHz. When used with a spectrum analyzer measurement bandwidth of 100 Hz, the system exhibits a sensitivity of -150 dBm at the test antenna output.To overcome high cable loss between the test antenna and the PR1000A assembly at 10 GHz, a remote low noise pre-amplifier (Praxsym PN 310-010091-001) is mounted directly onto the 10 GHz antenna.
-
Product
Proving Units for High Voltage Testing Equipment
-
A high quality range of proving units provide the important role of verifying the safe operation of high voltage potential indicators used by power engineers, maintenance personnel and service engineers. The proving units are essential tools for testing HV equipment before and after use.
-
Product
Thermal Cycling Test Equipment
-
Wewon Environmental Chambers Co, Ltd.
IC welding to PCB, IC is integrated in the chip general purpose circuit, it is a whole. Once the inside is damaged, the chip will be damaged. The goal of printed circuit boards (pcbs) is to connect IC and discrete components to form a larger working circuit. Thermal cycling equipment can detect the defects and hidden dangers of welding components in the production process, decreasing failure rate. When it fails, components can be replaced in timehttps://www.wewontech.com/thermal-cycling-test-equipment/
-
Product
Pipework Components & Hydraulic Equipment
-
Walter Stauffenberg GmbH & Co. KG
For more than 50 years, the companies of STAUFF Group have been developing, manufacturing and distributing pipework equipment and hydraulic components for mechanical and plant engineering and for service and industrial maintenance.
-
Product
Caibration Equipment For Lab Use
-
In the field of high-power semiconductor testing, PONOVO has launched a smart test platform with high-speed high-frequency, high-voltage, high-current power sources, combined with high-speed, high-precision high-voltage, high-current analog acquisition technology and high-speed digital processing control system. The platform can complete the testing of dynamic parameter parameters, static parameters, thermal parameters and mechanical parameters, and power life parameter of various types of high-power semiconductor devices, modules, and chips, which could meet different testing requirements. It is the universal testing platform for automated testing for different application purpose, such as the research and development testing, engineering acceptance test, factory acceptance test, etc.
-
Product
Optical Materials & LiDAR Test Equipment
-
Is a remote sensing method which is used to estimate the range between two objects.
-
Product
PCI Express 5 Base Specification Receiver Test Automation
N5991PB5A
-
The N5991PB5A is the receiver test automation software for bit error ratio testers, allowing you to test and characterize PCI Express 5.0 ASICs
-
Product
Automation Control
-
Schweitzer Engineering Laboratories, Inc.
Monitoring and controlling substation power systems requires comprehensive solutions. SEL’s complete solutions and hardened devices help maintain system stability with deterministic control; streamline access to valuable IED data, communications processors, and field devices; and improve visualization and control with local HMIs and access to SCADA systems.
-
Product
Battery Test & Automation Solutions
-
Chroma specifically developed battery cell test solution which is an integrated solution for battery cell formation & grading processes. From battery cell formation procedure to grouping process, Chroma 17900 series are customized with professional planning service which includes manufacturing flow path planning, test station/ equipment planning, test data management and so on to create high performance manufacturing capability.
-
Product
Automated Optical Inspection System
AV880 Series
-
The AV880 Series of AOI solutions from ASC International provides the same high level inspection capabilities as found in our AV862/AV871 Series of AOI systems all wrapped into an inline platform for continuous flow requirements. A price to performance ratio sure to please those looking for a quick ROI.
-
-
Product
UAV Ground Test Equipment (LTS)
MS 1103
-
*Checks integrated functionality of UAV*During integration checks it performs the functions of the Ground Control Station*Interface with Target Group Set (TGS)*Information is decoded and displayed in the display panel
-
Product
Imaging Automation
XImage
-
Whether you are a Microsoft Authorized Refurbisher, Microsoft Registered Refurbisher or just getting started in refurbishing, Erasure, Test and Re-Imaging are a must to get the most out of your assets. The problem is that until now, this required a big work force. One group to perform the testing and visual inspection, one group to perform erasure, someone to create and manage all your images and substantial knowledge on how to automate and deploy those images. Even with all of these bases covered, it can still be a complicated, time consuming task. Not to mention the fact that it is typically done in a separate process from data erasure, testing and auditing.
