Automatic Test Equipment
equipment that automatically analyzes functional or static parameters to evaluate performance. Also known as: ATE
See Also: Automatic Test Systems, ATE
-
product
Ethernet/LXI hybridNETBOX 16 Bit Digitizer and AWG - 125 MS/s on 8 DAQ Channels and 8 AWG Channels
DN2.806-08
The hybridNETBOX DN2.80/81x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 16 bit resolution and is available with sampling rates of 40 MS/s and 125 MS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
product
PXI MUX 8 Banks of 8 Channel Screened 1 Pole
40-610-021-S-8/8/1
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
product
PCI Very High Density Multiplexer, 24-Channel, 8-Pole
50-670C-022-24/8
The 50-670C-022-24/8 is a 24-channel, 8-pole MUX and is part of a series of very high density multiplexer cards feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.The 50-670C shares exactly the same architecture as the established 40-670 range of PXI modules.
-
product
Test Program Sets (TPS)
Data Review, Corrections, & Generation (Reverse Engineering). Technical Requirement Documentation (TRD). Test Strategy Reports (TSR). Test Program Development – Software. TPS Sell-Off & Acceptance. Life-Cycle Support. Technical Interface Test Adaptors (ITA) – Hardware. Training - TPS Development, ATE/TPS Operator, Fault Diagnostic, ATE Maintenance.
-
product
PXI Very High Density Multiplexer, 5-Channel, 32-Pole
40-675A-002-5/32
The 40-675A-002-5/32 is a 5-channel, 32-pole MUX and is part of our range of PXI very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
product
PXI Very High Density Multiplexer, 24-Channel 4-pole
40-670C-021-24/4
The 40-670C-021-24/4 is a 24-channel, 4-pole MUX and is part of a series of very high density multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
product
ATE Design & Build
PXI has become the de-facto standard for housing the high performance modular instrumentation required to meet the demands of testing today's high performance products. Based on the PCI bus, PXI (PCI Extensions for Instrumentation), this platform is used in most of our new ATE designs.
-
product
PXI High Density Multiplexer, 1-Bank, 128-Channel, 1-Pole
40-610A-004
The 40-610A-004 is a 1-bank, 128-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. The range includes a wide choice of switching configurations which are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems.
-
product
PCI Very High Density Multiplexer, 5-Channel, 32-Pole
50-670C-022-5/32
The 50-670C-022-5/32 is a 5-channel, 32-pole MUX and is part of a series of very high density multiplexer cards feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.The 50-670C shares exactly the same architecture as the established 40-670 range of PXI modules.
-
product
High Speed Digital Analog
The Automatic Test Equipment is designed to provide R&D and the Production floor with a high quality, reliable and easy to use Test Station comprised of COTS equipment from industry leading instrument manufactures. The measurement switching has low thermal offset allowing for micro volt measurements. The switching also accommodates both stimulus and measurement up to 5 Amps. Also to provide High Speed and Static Digital Stimulus and Response that covers LVDS, 3.3V, TTL, CMOS and Industrial logic families. For Serial communications there are SPI, I2C, RS232/485, USB and Ethernet. The system has nine programmable DC power supplies that are capable of powering both the UUT and the UUT interface separately. The system can interface with a variety of UUT’s via an ITA. Each system comes with the Imperial Test Executive, National Instruments TestStand, CVI, LabView and .NET Runtime.
-
product
PXI 2 Amp Multiplexer, Quad 8-Channel, 2-Pole
40-635A-009
The 40-635A-009 is a quad 8-channel, 2-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
ATE System Power Supply, 600 V, 2.6 A, 1560 W
N5772A
The N5772A single output, 1560 W system power supply provides universal AC input, GPIB, LAN, USB, LXI compliance, and analog/resistance control of output voltage and current. It delivers reliable performance and enhanced capabilities in a compact 1U package.
-
product
PXI/PXIe Very High Density Multiplexer, 198-Channel, 1-Pole
40-675B-002-198/1
The 40-675B-002-198/1 (PXI) and the 42-675B-002-198/1 (PXIe) are 198-channel, 1-pole multiplexers and are part of our range of very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems.
-
product
PXI 2 Amp MUX, Single 16-Channel 4-Pole
40-635-003
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
Mass Interconnect Solution
SCOUT
SCOUT is an innovative pull-through Mass Interconnect solution specifically designed to deliver the full performance potential of the PXI platform at the ATE interface. SCOUT, featuring DAK (Direct Access Kit) connectivity, enables system designers to limit or eliminate traditional instrument cables by replacing them with DAK connection modules that utilise PCB, flex-circuit or short wire connections.
-
product
PXI Multiplexer Single 24 Ch 2 Pole
40-632-021-24/2
This series of general purpose multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 68-pin connector. Available reed relay formats are 1-pole, 2-pole, 4-pole and 1-pole screened.
-
product
PXI Single 33x16 Matrix, 1-Pole
40-542-021
The highest density single slot PXI reed relay matrix module on the market today. This range also includes a 132x4 and 66x8 reed relay matrices with 1-pole switching. They are constructed using high reliability sputtered ruthenium reed relays, offering >10e9 operations to give maximum switching confidence with long life and stable contact resistance. Typical applications include signal routing in Functional ATE and data acquisition systems.
-
product
PXI 4 Slot BRIC 66x8 2-pole (3 sub-cards)
40-562A-022-66X8
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
Advanced Power System: Dynamic DC Power Supply, 120 V, 16.7 A, 2000 W
N7976A
The N7976A is designed for automated test equipment (ATE) applications where high-speed dynamic sourcing and measurement is needed.
-
product
PXI 8 Slot BRIC 10x32 1-Pole (2 sub-cards)
40-562A-121-10X32
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PXI 2 Slot BRIC 88x4 2-pole (2 sub-cards)
40-562A-222-88X4
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
Off-Line Testing Platform
6TL22
The 6TL22 Platform is a perfect base for the conception of a real modular Automatic Test Equipment for low to mid manufacturing volumes.A system designed around the 6TL22 is simple, easy to maintain, and cost-effective. The rack is prepared for the direct integration of the three platform-based receivers from Virginia Panel, the S6, G12 and G12X.The core of the system can be either an Industrial PC or a NI-PXI. A UPS will protect the valuable instrumentation as well as control all the steps for an automatic power-up and down of the test system.
-
product
Standalone Test System
1000 Series ATE
The Circuit Check 1000 Series ATE provides a configurable standard platform that can utilize multiple mass interconnect interfaces while providing ease of maintenance and the ability to accept a wide variety of test fixture solutions. With the 1000 Series ATE, test procedures become automatic, with test steps and go/no-go limits easily programmable.
-
product
Programmable DC Power Supply
62000P
Chroma Systems Solutions, Inc.
Chroma’s Programmable DC Power Supplies 62000P Series offer many unique advantages for ATE integration and testing. Advantages include: constant power operating envelope, precision readback of output current and voltage, output trigger signals as well as the ability to create complex DC transients waveforms to test device behavior to spikes, drops, and other voltage deviations.
-
product
PXI 8 Slot BRIC 110x8 1-Pole (5 sub-cards)
40-562A-121-110X8
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PXI High Density Multiplexer, 4-Bank, 40-Channel, 1-Pole
40-615A-007
The 40-615A-007 is a 2-bank, 80-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
product
PXI 4 Slot BRIC 276x8 1-Pole (6 sub-cards)
40-560A-021-276X8
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PXI High Density Multiplexer, 94-Channel, 1-Pole
40-640A-022-94/1
The 40-640A-022-94/1 is a 94-channel, 1-pole MUX and is part of a series of high density multiplexer modules featuring a choice of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
product
PXI Very High Density Mux Dual 10 Ch 8 Pole
40-670A-022-10/8
The 40-670A series of very high density multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
product
Virtual Test Methodology
TVT
With TVT, you don''t have to wait for the physical device to start validating your ATE test patterns, or verifying the device interaction with the tester.
