-
product
Network Simulation and Load Testing
EXFO offers a complete range of high-performance test solutions, covering the entire converged network from RAN to IMS. By mimicking real-world customer behavior in lab environments, our solutions allow mobile operators and equipment manufacturers to verify their wireless networks before deployment.
-
product
Develop - Simulate - Validate JTAG / IJTAG based IP
NEBULA
You, your vendors and your customers being able to use one common interface to control and observe on-chip IP, resources and instruments. The figure below shows an example IC. The new IEEE 1149.1-2013 standard supports an init-data register for configuring the analog paramaters of I/O as well as controlling on-chip PLLs. The standard further extends this by defining in BSDL user test data registers or 'scan chains'. These registers enable the ability of generic software to control and observe mission mode IP and instruments simply by describing the register interface in BSDL.
-
product
Electromagnetic Environment Simulators
A2PATS® Products
Our A2PATS Family of Products are electromagnetic environment simulators built upon Textron Systems' open-architecture direct digital synthesizer technology, coupled with our proven user interface. Our easily programmable, plug-and-play modular architecture uses identical, phase-coherent, direct digital Synthetic Stimulus Instruments (SSIs) as the radio frequency (RF) source for all signals. These modular commercial RF Sources are easily configured in our commercial cabinets. Four standard configurations are available including single-cabinet, multi-cabinet, mini-A2PATS, and A2DSG™.The A2PATS Family consists of numerous commercial products including but not limited to A2PATS, A2DRI™, A2DSG and A2EOSTIM.
-
product
Radar Systems
A radar system utilizing electronic-computer techniques whereby raw data is used to track an assigned target, compute target velocity, and predict its future position without interfering with the scanning rate.
-
product
Radar Detectors
Explore our collection of premium radar detectors designed to fit your driving style and preferences.
-
product
Radar Threat and Target Simulation Unit
MS 1605
PTG is used to field/LAB evaluation / testing of RADAR. PC is used to control the profile of the target generation. PTG will work in both stand alone and remote mode. The PTG has keypad and LCD for stand-alone operation. The PC can interface the PTG through the USB link. The operator can communicate through the GUI to the PTG. MIL1553B Communication used for Interfacing with RADAR.
-
product
Radar solutions for transport & logistics
With OndoSense radar sensors you will enhance your productivity in the transport sector, increase the reliability of your means of transport or cranes and automate the work processes in logistics.
-
product
MULTI-STANDARD LOCAL LOOP SIMULATOR
458-LM-A8-30
Accurately simulates attenuation and impedanceFull bidirectional operation at all specified frequencies26 AWG PIC as specified in ANSI T1.417
-
product
Open-source CAD tool to simulate 2D and 3D-ICs.
IntSim v2.0
Simulate and optimize 2D and 3D-ICs. Pre-silicon estimates for die size, number of metal levels, size of each metal level and chip power.
-
product
X-Band Silicon Radar Quad Core IC
AWS-0105
The AWS-0105 is a highly integrated silicon quad core IC intended for radar and 5G phased array applications. The device supports four radiating elements, single beam transmit, and single beam receive and includes all requisite beam steering controls for 6 bit phase and gain control. The device provides 21 dB gain and +15 dBm output power during transmit mode and 7 dB gain and +7 dBm IIP3 during receive mode. Additional features include gain compensation over temperature, temperature reporting, and fast beam switching using eight on-chip beam weight storage registers. The device features ESD protection on all pins, operates from a +1.8 V supply, and is packaged in a 56 lead 7x7 mm QFN for easy installation in planar phased array antennas.
-
product
PCI Strain Gauge Simulator Card, 6-Channel, 350 Ohm
50-265-016
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
product
HBM Discharge Simulator
PSD-510
The PSD-510 is a low cost, light weight, battery powered Human Body Model (HBM) simulator designed to help customers determine the HBM ESD sensitivity of a device in accordance with ANSI/ESDA/JEDEC JS-001.
-
product
Troubleshooting Track Circuit Simulators
14900 Series
The 14900 seriesTrack Simulator features a front panel with standard set up resistors and terminals and electrically conductive model track to simulate a track circuit suitable for instructional and hands-on training purposes. A locked drawer provides additional switches, potentiometers, and controls that allow selective implementation of many faults commonly found in typical track circuits.
-
product
MIMIC SNMP Simulator
MIMIC SNMP Simulator creates a network of up to 100,000 SNMP manageable devices on one server. You can simulate any SNMP based device with any number of public or private MIBs to run a large variety of device configurations with your SNMP management application. It lets you generate thousands of traps to simulate disaster scenarios.
-
product
Capacitance Simulation Card
SET-1220
The SET-1220 device is a designed capacitive fuel sensor emulation for NI-SLSC. This card provides eight isolated channels that can emulate capacitance values between 10pF and 800pF. It was designed to emulate capacitive sensors that are typically connected between an excitation voltage on one end and a virtual ground on the other end.
-
product
2 PRI + 32 BRI-S/T ISDN Simulator
CH-32BRI-ST-MOD-2PRI
This unit has two PRI ports and 32 BRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network
-
product
Mid-Range Perimeter Surveillance Radar
Ranger® R2
The Ranger® R2 is a high-resolution radar that accurately detects personnel and vehicles at a range of up to 1,400 m. This ground-based radar works in virtually any climate, weather, or lighting condition, providing 24/7 security. Additional units — such as a short-range Ranger® R1 — can be networked in an overlapping array to protect larger areas, stitching together an impassable radar area outside and inside your perimeter.
-
product
Short-Range Perimeter Surveillance Radar
Ranger® R1
The Ranger® R1 is a ground-based perimeter surveillance and tracking radar that accurately detects personnel and vehicles at a range of up to 700 m. It scans a full 360° every second, covering up to 1.5 square km (0.6 square miles). Additional units — such as a mid-range Ranger® R2 — can be networked in an overlapping array to protect larger areas, stitching together an impassable radar area outside and inside your perimeter.
-
product
Solar Simulators
TriSOL CPV
Concentrating Photovoltaics (CPV) has the promise of producing solar cells with high cell efficiencies, which result in a reduction in the cost of operating a PV module. However, a CPV system requires the integration of CPV solar cells, modules and CPV optics into one efficient system. OAI’s focus is CPV cell testing methodology. The CPV cells can now be tested using OAI’s advanced standalone CPV Simulators for low dose and high dose configurations. The low dose CPV Solar Simulator provides exposure up to 50 Suns, whereas, the high dose CPV Solar Simulator provides exposure up to 1500 Suns. The low and high dose simulators provide exposure in varying Sun concentrations in various beam sizes from 1.5cm x 1.5cm to 7.5cm x 7.5cm, and may be configured with OAI’s I-V Test Systems.
-
product
Radar Detectors
histler''s FDSR (Field Disturbance Sensor Rejection), the most recent advancement to combat new vehicles equipped with Frequency-Modulated Continuous Wave (FMCW) K band blind spot and collision avoidance devices that clutter nearly all of K band causing a normal radar detector to alert continuously.
-
product
4 Port BRI-S/T ISDN Simulator
BRI-4ST
The unit has four S/T ports allowing ISDN basic rate terminal equipment to be connected together just as if they were connected through the ISDN network.
-
product
Infrared Simulation Services
INO offers a simulation service to assist with the hardware and software design of infrared and electro-optical devices. Precise performance predictions help integrators understand application requirements and bring application performance in line with client specificationsbefore the advance design and fabrication phases. For a minimal investment, infrared simulations help minimize risk in the early stages of development.
-
product
Pulse Radar Reference Test Solution
Compact Reference Solution with ADP7104, M8195A, WR15CCU, WR15CCD, N5183B combines commercial off-the-shelf COTS modular hardware and software from Guzik, Keysight Technologies, KJ Microwave and Virginia Diodes, which provides a flexible testbed for radar waveform generation and analysis. Generate and analyze pulse radar waveforms. Pre-correct waveforms for overall channel response. Supports many topologies for radar transmitter / receiver testing (IQ, IF, RF, microwave, millimeter-wave).
-
product
Fibre Channel Test & Simulation Interface for PCI
PCI-FC4
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
product
Manikins for realistic simulation of the acoustic properties of a human
Head & Torso Simulators
If you need to carry out realistic in-situ measurements of headphones, telephones or hearing aids, you need a Head and Torso Simulator such as the B&K ‘HATS’ – Type 4128D or GRAS’ Kemar to complete your test setup. These manikins have built-in ear and mouth simulators that provide a realistic reproduction of the acoustic properties of an average adult human head and torso. They are commonly used for tests on telephone handsets, headsets, audio conference devices, microphones, headphones, hearing aids and hearing protectors. Please contact your sales engineer or email sales@listeninc.com for more information.
-
product
Interference Modeling And Simulation
The CAST Navigation Jammers are designed to facilitate and support the testing, verification, and integration of single element Fixed Reception Pattern Antenna (FRPA) systems as well as multiple-element anti-jam antenna sub-systems such as Controlled Reception Pattern Antennas (CRPAs). These systems are an ideal solution for military and commercial laboratories where interference signal capability is required. CAST Jammer sub-systems provide precisely controlled signals for use in most types of GNSS testing applications, emulating interference conditions and threats that can occur in both urban and hostile environments.
-
product
2 Port BRI-S/T ISDN Simulator
BRI-2ST
The most inexpensive ISDN simulator on the market. The unit has two S/T ports allowing ISDN basic rate terminal equipment to be connected together just as if they were connected through the ISDN network.
-
product
Hot Dipping Simulator
HDPS
This is a hot-dip galvanizing simulator that simulates various hot-dip galvanizing processes such as heating, cooling, vacuuming, gas replacement, and spraying of steel sheets on a laboratory scale. It is possible to simulate the parameters close to the actual line, such as zinc bath temperature, immersion speed, immersion time, and gas flow rate adjustment for weight control. Also, 20 to 25 sheets can be tested
-
product
Central Office Line Simulator
AI-7280
The AI-7280 is a highly flexible central office line simulator. It is designed primarily for the testing and verification of common terminal equipment, including standard telephones, Caller ID devices, SMS (Short Message Service) capable equipment, and any device using an analog Tip/Ring interface circuit. Supplied with the TRsSim software for Windows, it can analyze a telephone''s DTMF characteristics, pulse dialing and flash timing, generate various network tones and ringing patterns. Both Type I (on-hook) and Type II (off-hook) Caller ID is supported using either FSK or DTMF data transmission. As an optional component, the TRsSim software can perform SMS testing to either the ETSI protocol 1 or protocol 2 standards.
-
product
PXI Analog Output/Current Loop Simulator Module - 4 Channel
41-765-004
The 41/43-765-004 is an 4-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
