Product

Coaxial Waveguide Adapter, 1.0 mm (f), 50 to 75 GHz

V281C

-

Keysight Technologies

V281C - Keysight Technologies

The Keysight V281C is a 1-mm female to V-band waveguide adapter with a frequency range of 50 GHz to 75 GHz. The V281C is used with the Keysight 8510XF systems.

Product

Manual Fixture Kit With Mass Interconnect Cassette Interface, Max number of probes (2N) 1000 units, Max UUT 580 x 400 mm (wxd)

CMCSK-04-01

-

Columbia Elektronik AB

CMCSK-04-01 - Columbia Elektronik AB

Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.

Product

RF Electronic Calibration Module (ECal), DC/300 KHz To 9 GHz, 3.5 Mm, 2 Port

85093D

-

Keysight Technologies

85093D - Keysight Technologies

The Keysight 85093D RF electronic calibration (ECal) module makes the calibration of vector network analyzers fast, easy, and accurate. ECal is a precision, single-connection calibration technique for your vector network analyzer. Performing a full two-port calibration takes less than half the time and a number of connections using ECal versus mechanical calibration kits. Furthermore, the accuracy of the calibration is comparable between electronic and mechanical methods. Traditional mechanical calibrations require intensive operator interaction, which is prone to errors. With ECal, the operator simply connects the ECal module to the network analyzer and the software controls the rest.

Product

Flexible Cable Set, 2.4 Mm To 7 Mm

85135F

-

Keysight Technologies

85135F - Keysight Technologies

Achieve phase stability with these 62.9-cm cables when a DUT is connected between cable ends

Product

4-in-1 OSLT Calibration Kit, DC to 70 GHz, Type-1.85 mm (f)

CK058F

-

Spanawave Corporation

CK058F - Spanawave Corporation

The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.

Product

ICT/FCT-Fixtures, Max UUT 370 × 300 mm (wxd)

CK-2-228X (Small IF) / 230540

-

Columbia Elektronik AB

CK-2-228X (Small IF) / 230540 - Columbia Elektronik AB

The series of In-Circuit testers that are Teradyne for the 228x and TestStation are dedicated tools that rely on the tester hardware for diagnostics and test pattern delivery. The integration of the stand-alone BTS with the Teradyne ICT can enhance the system’s capability. In other words, it can provide access to additional tools. It provides the user with a common platform and portability of test patterns from stand-alone to ICT and later on to functional test and depot test stations.

Product

In-Line Coaxial-to-Waveguide Adapter, 1.0 Mm (f) To WR-12, 60 To 90 GHz

E281CS

-

Keysight Technologies

E281CS - Keysight Technologies

E281CS E281CS In-line 1.0 mm (f) - to- WR-12 waveguide adapter offers a simple way of measuring waveguide devices in E-band, 60 GHz to 90 GHz.

Product

Input Adapter with 4 mm plug

PK007-023

-

Teledyne LeCroy

PK007-023 - Teledyne LeCroy

Input Adapter with 4 mm plug.

Product

Compact Case 20 L | Comfort | 300 mm

20C-401-300

-

ELMA Electronic, Inc.

20C-401-300 - ELMA Electronic, Inc.

The Compact Case 20 combines flexibility, practicability and intelligent design. Available in four different sizes and three different finishing options. Optionally also with EMC protection.

Product

Cable Continuity Tester, VGA/UL2919 Mini, Network, 21.01 mm, 35 mm, 45.01 mm

72-9205

-

Tenma

72-9205 - Tenma

Quickly test VGA / UL2919 cables No need to carry bulky, expensive cable testers to test only one or two cable types Mini cable tester fits easily in your pocket or tool box, and requires no external power Confirms conductor continuity with sequential LED's Save time and money by diagnosing connectivity issues All units are powered by a cross compatible 3xAA battery pack or USB cable (both included) Most units measure 2" x 2" x 1" or less!

Product

Coaxial Waveguide Adapter, 2.4 mm (m), 33 to 50 GHz

Q281B

-

Keysight Technologies

Q281B - Keysight Technologies

The Keysight Q281B is a 2.4 mm male to WR-22 waveguide adapter that operates in the 33 to 50 GHz frequency range. These adapters transform waveguide transmission lines into 50 ohm coaxial lines. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.

Product

Resistivity Cell For N1413 (50 Mm Electrodes)

N1424A

-

Keysight Technologies

N1424A - Keysight Technologies

The N1424A is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It is used to measure surface or volume resistance/resistivity of insulation materials. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1424A to the B2985B/87B.

Product

Test Port Adapter Set, 3.5 Mm (Test Port) To Type-N

85130C

-

Keysight Technologies

85130C - Keysight Technologies

The Keysight 85130C test port adapter is designed to protect the test set port when it would be directly connected to the device under test. These adapters have a special rugged female connector designed for connecting to the network analyzer test port. This special connector will not mate with a standard male connector, but converts the rugged test set port to a connection that can be mated with the device under test. The set contains a 3.5 mm to type-N male adapter and a 3.5 mm to type-N female adapter. The frequency range for these adapters is dc to 18 GHz with a return loss of 28 dB or better.

Product

Adapter, 1.0 Mm (m) To 1.0 Mm (m), DC To 120 GHz

Y1910A

-

Keysight Technologies

Y1910A - Keysight Technologies

Provides measurement accuracy, versatility, and ease of use for on-wafer and coaxial measurements.

Product

Adapter, 1.0 mm (m) to 1.85 mm (m), DC to 67 GHz

11921E

-

Keysight Technologies

11921E - Keysight Technologies

The Keysight 11921E precision 1.85 millimeter coax-to-coax adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms impedance and frequency range from dc to 67 GHz.

Product

Moisture Meter, 0% to 100%, 1 %, 189 mm, 47 mm

72-10202

-

Tenma

72-10202 - Tenma

This pinless moisture meter quickly measures the moisture content of a variety of materials.

Product

Clamp Meter, True RMS, 100 A AC, 600 V AC, 600 V DC, 17 mm Jaw Opening Max.

72-2985

-

Tenma

72-2985 - Tenma

The 72-2985 from Tenma is a mini clamp meter in orange and grey colour. It features high reliability, safety precision and compact design. Its resolution ratio is 1mA, maximum range has maximum range of 100A AC/DC, particular VFC start mode. Entering this mode can accurately measure voltage and current which has VFC frequency conversion. Voltage or current response display is true valid value. Whole range overload protection, reliable measurement accuracy and unique appearance design makes it an outstanding new generation functional electrician/electric power measurement instrument. This complies with EN 610101-1, 61010-2-032, 61010-2-033, pollution degree 2, measurement category: (CAT II 600V, CAT III 300V) and double insulation standards. Conforms to UL STD. 61010-1, 61010-2-032, 61010-2-33 certified to CSA STD. C22.2 NO. 61010-1, IEC STD 61010-2-032, 61010-2-033.

Product

High Accuracy Internal Measurement Ultima

-

Sylvac

Sylvac

• Ultima handles and kits with display unit D62S Advanced und absolute digital probe P12D• Measuring range from 2 to 310 mm• Resolution up to 0.0001 mm• Mechanical repeatability : 1μm from 2 to 60 mm, 1.5μm from 60 to 210 mm and 2μm from 210 to 310 mm• Robust construction designed for use by inspection and machine shop• UKAS certificate supplied with each head• UKAS certificate supplied with each setting ring.• Rings manufactured according to DIN 2250 part 2 (standard)• Blind bore measuring from 12 to 310 mm• Compatible with all Sylvac digital display• Special heads on request ( threads, grooves, splines, slot width, etc...)

Product

Manual Fixture Kit

230353 – CMK-04

-

Columbia Elektronik AB

230353 – CMK-04 - Columbia Elektronik AB

Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.

Product

Intel® SDM Large

-

Axiomtek Co., Ltd.

Axiomtek Co., Ltd.

Intel® SDM Large measures just 175 x 100 mm and a maximum z-height of 1.6 mm, which is well-suited for ultra slim displays. The Intel® SDM–L is optimized for digital signage, interactive flat panel displays, interactive touch computers, video walls, etc.