Product

Low Voltage DC / Battery Powered HV Amplifiers

WMA-01 And WMA-01LF

-

Falco Systems

WMA-01 And WMA-01LF - Falco Systems

The Falco Systems WMA-01 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-01LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.

Product

Voltage Probe

KHZ43201

-

Beijing KeHuan Century EMC Technology Co,.LTD

KHZ43201 - Beijing KeHuan Century EMC Technology Co,.LTD

The KHZ43201 voltage probe is a standard low resistance test probe, which meets the technical requirements for this product in the CISPR16-1 and CISPR14-1 test equipment. When measuring the interference voltage of the power grid, the artificial power supply network cannot be used at the load port, and sometimes it is necessary to use a voltage probe to measure the interference of the signal port, the load port, and the antenna port. The input impedance of the voltage probe to the ground wire is greater than 1.5KΩ, which can protect the input terminal of the receiver.

Product

Standard Voltage 37 Pin D-Type Connector Blocks for Pickering

-

Pickering Interfaces Inc.

Pickering Interfaces Inc.

The connector blocks below are suitable to use with Pickering cards and modules that utilize a standard voltage 37-pin D-type connector.

Product

High Voltage Isolator for Logic Analyzers

LX-08

-

Link Instruments

LX-08 - Link Instruments

The LX-08 series of high voltage logic analyzer adapters provides a safe isolated method of measuring high voltage control signals with a low voltage logic analyzer. All inbound signals are optically isolated and attenuated to a safe level for the delicate inputs typically found on logic analyzers. The inputs on the LX-08 are capable of withstanding voltages up to +/- 300V AC/DC, higher voltage configurations are available upon request. Rather than probing with multiple neon screwdrivers, the LX-08 can provide simultaneous viewing of up to 8 circuits in the STANDALONE mode via the indicator array. Need to catch a transient event or map out a timing sequence? Just add a logic analyzer to the outputs of the LX-08 and turn it into a high voltage logic analyzer. High voltage signals that were hazardous for a logic analyzer can now be measured safely. Typical outputs of a high speed PLC sequencer can be precisely timed and measured from both sides of the control relay. With the built in user selectable AC filter circuit, an AC signal can be measured as DC events or AC cycles.

Product

Calibration Wheel

-

Mountz Inc.

Mountz Inc.

A torque analyzer or a torque sensor are a finely tuned instrument designed for testing and monitoring torque applications. In order to maintain accuracy, it is crucial that torque measuring equipment be properly calibrated regularly. Calibration wheel is engineered for calibrating torque analyzers and sensors and ensuring instruments are traceable to National or International Standards, such as N.I.S.T and ISO.

Product

Voltage Testers

-

Kyoritsu Electrical Instruments Works, Ltd.

Kyoritsu Electrical Instruments Works, Ltd.

AC and DC voltage tests up to 690V with LED Comply with the latest standards IEC 61243 and IEC 61010 Novel designLarge and bright LEDs: Values are visible in the dark placeErgonomic design fits in the hand Two functions are available in one model"Measurement without battery" and "Self Test (all LED on)" Test leads withstand harsh environments at low temperature Penlight (white LED) Auto-power ON/OFF Audible indication Variable test tips, 2mm or 4mm Probe protection cover can store the attachment of caps IP65 (IEC 60529)

Product

Voltage, Continuity & Current Tester

T5-1000

-

Fluke Corporation

T5-1000 - Fluke Corporation

Measure current up to 100 A without breaking the circuit with OpenJaw™ design. The T5-1000 Electrical Tester is a versatile troubleshooting tool to carry to every job site. Use it to check voltage, continuity, and current–all with one compact tool.

Product

High Voltage Programmable DC Power Supplies

-

TDK-Lambda Corp.

TDK-Lambda Corp.

High Voltage Programmable DC Power Supplies

Product

Calibration Solutions

-

Sper Scientific

Sper Scientific

Calibration or buffer solution lets you calibrate any pH tester to ensure accuracy. Choose from pH 4, 7 or 10. Calibration solution helps you achieve the accuracy that's critical for measuring pH in wastewater, stormwater and process liquids. Sper Scientific offers both liquid and buffer pouches, which are ideal for field use.

Product

High Voltage 50 Pin D-Type Connectors for Pickering Products

-

Pickering Interfaces Inc.

Pickering Interfaces Inc.

The connectors below are suitable to use with Pickering cards and modules that utilize a high voltage 50-pin D-type connector.

Product

NIST Calibration for D610-A

D610-A-CCNIST

-

Teledyne LeCroy

D610-A-CCNIST - Teledyne LeCroy

- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead

Product

15k Voltage Probe Set With Hot Sticks

15KVPSet

-

Summit Technology, Inc.

15KVPSet - Summit Technology, Inc.

Our 15KVPSet is a set of three voltage probes that allow direct connections up to 15,000 Vrms (15KV) 3 phase power.

Product

Optical Power Meter W/6 Wavelength Calibrating Spots

-

Maxcom Inc.

Maxcom Inc.

With six wavelength calibrating spots (980nm, 1310nm, 1490nm, 1550nm, 1590nm and 1610nm), refined design, easy operation, linearity or non-linearity display, SC connector, the MXOPM26-50 hand-held optical power meter can be used for direct optical power measurement as well as relative measurement of optical link loss. It’s an essential test instrument in Optical Communication systems, CATV systems, construction and maintenance applications and more.

Product

4-in-1 OSLT Calibration Kit, DC to 50 GHz, 2.4 mm (m)

CK564A

-

Spanawave Corporation

CK564A - Spanawave Corporation

The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.

Product

Ultra High Voltage DC Power Supply

-

Twintex Electronics Co., Ltd

Twintex Electronics Co., Ltd

Output control can be switched between remote control and local control. The output display and output indicators are located directly on the front panel and can be directed to an external remote display. The high voltage output terminal has overcurrent, overvoltage, short circuit protection and arc protection.

Product

Quasi Square Wave Constant Voltage Transformers

-

Osborne Transformer Corp.

Osborne Transformer Corp.

Osborne Quasi Square Wave Constant Voltage Transformers are used to regulate output voltages for applications that have varying input voltages. When used with a rectifier conversion circuit, these units provide an elegant design approach to voltage regulation. Osborne achieves this innovative approach by partnering the constant voltage transformer with an auxiliary resonant capacitor winding. The result is a unique (though time honored) technology that offers reliability, performance, and cost advantages over other styles of voltage regulation.

Product

Spectral Radiant Flux / Luminous Flux Calibration Standards

-

Gigahertz-Optik GmbH

Gigahertz-Optik GmbH

Standard lamps calibrated in luminous flux and spectral radiant flux. Versions with 2-Pi and 4-Pi emission characteristics. Traceable calibrations in the wavelength range from 200 nm to 2500 nm.

Product

RH Calibrator / Dew Point Generator

-

Edgetech Instruments

Edgetech Instruments

Edgetech Instruments'' portable calibration system offers the highest accuracy available for both relative humidity and temperature. Using chill mirror technology and precision PRT's, Edgetech''s calibrators offer best repeatability, stability and reliability when measuring RH and temperature. The calibrators are used mainly by calibration labs as a reference standard.The Edgetech Instruments dew point generator, DewGen, another calibration lab favorite, can be used as a stand alone or with a NIST traceable chill mirror dew point system creating very accurate dew points or frost points. Depending on the dry gas source this generator can create dew points from +15C to -80C.

Product

CableEye Tester Calibration Verification Board | Cable & Harness Tester

CB50

-

CAMI Research Inc.

CB50 - CAMI Research Inc.

Populated with precision resistors, it allows users to determine empirically whether the tester requires calibration. The CB50 may be used on all CableEye models. The CB50 is intended for periodic verification of tester calibration. To ensure that resistance measurements remain accurate, CAMI recommends yearly calibration. However, depending on environmental conditions and usage, testers may need calibrating more or less frequently.

Product

High Voltage Fiber Optic Probe, 150 MHz Bandwidth

HVFO108

-

Teledyne LeCroy

HVFO108 - Teledyne LeCroy

- Ideal for GaN and SiC devices- Highest system accuracy- Fastest rise time- High CMRR - 160 dB

Product

Pressure Calibrators

-

Fluke Calibration

Fluke Calibration

Wherever you need to work and whatever pressure range you need to work with, our broad selection of tools will meet your needs. From pneumatic or hydraulic deadweight testers and test pumps to electronic deadweight testers, bench controllers, and precise analog pressure gauges, we have you covered at the bench. Going into the field? Fluke’s portable pressure calibrators – with or without pumps and intrinsically safe or not – work with gases or liquids, source and measure, power transmitters, and cover a wide range. With individually available pressure modules, our portable and bench solutions cover pressures from vacuum to 10,000 psi.

Product

Electronic Calibration Module (ECal), 40 GHz, 2.92 Mm, 2-port

N4692D

-

Keysight Technologies

N4692D - Keysight Technologies

The Keysight N4692D microwave electronic calibration (ECal) module makes calibration of Keysight vector network analyzers fast, easy and accurate. The N4692D is a precision 2-port ECal module that supports 2.92 mm connectors up to 40 GHz. Select either female-female, male-male, or female-male connectors. The plastic storage case for the N4692D is included for securing your ECal module and accessories.